Shark ION F30/F60 Cord-Free MultiFlex IF200, IF250 Series - Vacuum Cleaner Manual

IMPORTANT SAFETY INSTRUCTIONS

FOR HOUSEHOLD USE ONLY • PLEASE READ CAREFULLY BEFORE USE

If the plug does not fit fully into the outlet, reverse the plug. If it still does not fit, contact a qualified electrician. DO NOT force into outlet or try to modify to fit.

To reduce the risk of fire, electric shock, injury, or property damage:

THE DUOCLEAN^® FLOOR NOZZLE, WAND, AND HANDVAC CONTAIN ELECTRICAL CONNECTIONS

1. This vacuum consists of a motorized nozzle, wand, and handvac. These components contain electrical connections, electrical wiring, and moving parts that potentially present risk to the user.
2. Before each use, carefully inspect all parts for any damage. If a part is damaged, discontinue use.
3. Use only identical replacement parts.
4. This vacuum contains no serviceable parts.
5. Use only as described in this manual. DO NOT use the vacuum for any purpose other than those described in this manual.
6. With the exception of filters, DO NOT expose any parts of the vacuum to water or other liquids.

GENERAL USE

7. This vacuum is not intended for use by anyone with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. Children should be supervised to ensure that they do not play with the vacuum.
8. Always turn off the vacuum before connecting or disconnecting any current carrying hoses, motorized nozzles, chargers, batteries, or other electrical or mechanical parts.
9. DO NOT handle plug or vacuum with wet hands.
10. DO NOT use without dust cup, filters, and brushrolls in place.
11. Only use Shark^® branded filters and accessories. Failure to do so will void the warranty.
12. DO NOT put any objects into nozzle or accessory openings. DO NOT use with any opening blocked; keep free of dust, lint, hair, and anything that may reduce airflow.
13. DO NOT use if nozzle or accessory airflow is restricted. If the air paths or the motorized floor nozzle become blocked, turn the vacuum off and remove the battery. Remove all obstructions before you reinsert the battery and turn on the unit again.
14. Keep nozzle and all vacuum openings away from hair, face, fingers, uncovered feet, or loose clothing.
15. DO NOT use if vacuum is not working as it should, or has been dropped, damaged, left outdoors, or dropped into water.
16. Use extra care when cleaning on stairs.
17. DO NOT leave the vacuum unattended while powered on.
18. When powered on, keep the vacuum moving over the carpet surface at all times to avoid damaging the carpet fibers.
19. DO NOT place vacuum on unstable surfaces such as chairs or tables.
20. DO NOT use to pick up:
    1. Liquids
    2. Large objects
    3. Hard or sharp objects (glass, nails, screws, or coins)
    4. Large quantities of dust (including drywall, fireplace ash, or embers). DO NOT use as an attachment to power tools for dust collection.
    5. Smoking or burning objects (hot coals, cigarette butts, or matches)
    6. Flammable or combustible materials (lighter fluid, gasoline, or kerosene)
    7. Toxic materials (chlorine bleach, ammonia, or drain cleaner)
21. DO NOT use in the following areas:
    1. Poorly lit areas
    2. Wet or damp surfaces
    3. Outdoor areas
    4. Spaces that are enclosed and may contain explosive or toxic fumes or vapors (lighter fluid, gasoline, kerosene, paint, paint thinners, mothproofing substances, or flammable dust)
22. Turn off the vacuum before inserting or removing the battery, as well as before plugging in or unplugging the charger.
23. Turn off the vacuum and remove the battery before any adjustment, cleaning, maintenance or troubleshooting.
24. During cleaning or routine maintenance, DO NOT cut anything other than hair, fibers, or string wrapped around the brushroll.
25. Allow all filters to air-dry completely before replacing in the vacuum to prevent liquid from being drawn into electric parts.
26. DO NOT modify or attempt to repair the vacuum or the battery yourself, except as indicated in this manual. DO NOT use the battery or vacuum if it has been modified or damaged.

BATTERY PACK

27. The battery is the power source for the vacuum. Carefully read and follow all charging instructions.
28. To prevent unintentional starting, ensure the vacuum is powered off before picking up or carrying the vacuum. DO NOT carry the appliance with your finger on the power switch.
29. Use only Shark^® chargers YLS0243A-T288080 or YLS0483A-T2880802. Use of incorrect charger may create a risk of fire when used with ION Power Pack Battery XBAT200.
30. Keep the battery away from all metal objects such as paper clips, coins, keys, nails, or screws. Shorting the battery terminals increases the risk of fire or burns.
31. Under abusive conditions, liquid may be ejected from the battery. Avoid contact with this liquid, as it may cause irritation or burns. If contact occurs, flush with water. If liquid contacts eyes, seek medical help.
32. Battery should not be stored at temperatures below 37.4°F (3°C) or above 104°F (40°C) to maintain long-term battery life.
33. DO NOT charge battery at temperatures below 50°F (10°C) or above 104°F (40°C).
34. Store the appliance indoors. DO NOT use or store it below 37.4°F (3°C). Ensure the appliance is at room temperature before operating.
35. DO NOT expose the battery to fire or temperatures above 265°F (130°C) as it may cause explosion.

SAVE THESE INSTRUCTIONS

ASSEMBLY

1. Insert wand into floor nozzle.
2. Insert handheld vacuum into wand.
3. Insert battery into handheld vacuum.

For proper operation, ensure all components are firmly connected.

YOUR ION POWER PACK BATTERY

Your ION Power Pack Battery does not come fully charged. Prior to first use, charge completely. During first use, discharge fully to condition your ION Power Pack Battery. Failure to do so may cause LED indications to work incorrectly.

RECYCLING THE ION POWER PACK BATTERY

When your ION Power Pack Battery needs to be replaced, dispose of it or recycle it in accordance with local ordinances or regulations. In some areas, it is illegal to place spent lithium-ion batteries in the trash or in a municipal solid waste stream. Return spent power packs to an authorized recycling center or to retailer for recycling. Contact your local recycling center for information on where to drop off the spent power pack.

RUNTIMES PER FULLY-CHARGED BATTERY

LED BATTERY POWER METER

Charging

Low Charge

Mid Charge

Nearly Full

Full Charge

NOTE: Full charge takes approximately 3.5 hours.

In Use

Full Charge

Mid Charge

Low Charge

Nearly Empty

No Charge

NOTE: A complete charge takes approximately 3.5 hours. The ION Power Pack, like all lithium-ion products, will naturally decrease in capacity over time from the 100% capacity of a new battery.

CHARGING THE ION POWER PACK BATTERY

USING THE ION POWER PACK CHARGER

USING THE ION POWER PACK CHARGING DOCK

Connect ION Power Pack Battery Charger to the Charging Dock by inserting into hole and turning clockwise to lock.

Place battery onto dock, then connect charger to wall outlet.

NOTE: Not all units come with the charging dock. See enclosed Quick Start Guide for your configuration.

SMART RESPONSE™ TECHNOLOGY

Suction Settings
ION POWER
For everyday cleaning.

ION BOOST
Press for a timed 1-minute boost of increased suction for high-traffic areas and heavy messes.

To use ION BOOST mode for longer than 1-minute, you can re-press the ION BOOST button when the 1-minute period ends.

You can end ION BOOST mode prior to the 1-minute by pressing the ION BOOST button.

Press and hold ION BOOST for manual control of the mode for as long as you need it.

PLEASE NOTE: Use of ION BOOST Mode will drain your ION Power Pack faster.

NOTE: Select Carpet setting for stuck-on dirt and debris.

NOTE: For deep cleaning per ASTM F 608 (embedded dirt in carpets) please select CARPET and ION BOOST settings.

VERSATILE CLEANING

FLOOR

Press the Power button, then choose your Surface setting and your Suction setting. Place your foot gently on the floor nozzle and tilt the handle back.

For low furniture, take advantage of the MultiFlex™ wand.

NOTE: Brushroll will only engage when the handle is tilted back.

ABOVE FLOOR

Press the Wand Release button to disconnect the handheld vacuum. Attach accessory, then press the power button.

Stand the vacuum upright. Step on the Floor Nozzle Release pedal and pull the wand up to disconnect it from the floor nozzle. Attach accessory, then press the power button.

NOTE: All accessories are compatible with both the handheld vacuum or the wand.

USING THE MULTIFLEX^® WAND

MULTIFLEX REACH

Press the MultiFLEX Wand button to position the wand to a lower angle for ease of use under low furniture.

MULTIFLEX STORAGE

Press the MultiFLEX Wand button and hold it down while folding the handheld vacuum forward. Use the handle to carry the vacuum.

To take the vacuum out of storage mode, press the MultiFlex Wand button while lifting up the handheld vacuum.

MAINTAINING YOUR VACUUM

EMPTYING THE DUSTCUP

Disconnect the hand vacuum from the wand.

Press the dust cup Empty button.

CLEANING THE FILTERS

To clean filters, rinse with water only to prevent damage from cleaning chemicals. Allow all filters to air-dry for at least 24 hours before replacing them in the vacuum to prevent liquid from being drawn into electric parts.

DO NOT use soap when cleaning the filters.

Remove cover and frame. Slide filter off frame. Rinse with water. Air-dry completely for at least 24 hours before reinserting. Tap off loose dirt between washes as needed.

Remove cover and filter. Rinse filter with water. Air-dry completely for at least 24 hours before reinserting. Tap off loose dirt between washes as needed.

NOTE: To order filters and other parts, visit sharkaccessories.com.

ACCESSING BRUSHROLLS

Open the brushroll garage by sliding back the release buttons. To close, insert the tabs on the lid into the slots on the nozzle, then press down both sides.

Securely close the garage door by clicking it in to place on both sides.

NOTE: Failure to secure on both sides will result in the headlights flashing and the brushrolls will not spin.

CLEANING BRUSHROLLS

Run scissors along the guide on the brushroll to remove any string, hair, or debris.

Pull out roller by the tab. Remove any string, carpet fibers, or hair, and remove debris from the roller housing. Wash the roller as needed, using only water. Air-dry completely for at least 24 hours before reinserting.

Reinsert roller by sliding it into the front of the floor nozzle until it clicks into place.

CHECKING FOR BLOCKAGES

Turn off vacuum and remove battery.
Remove the handheld vacuum from the wand and check all intake openings to the dust cup.

Turn off vacuum and remove battery.
Remove the hand vacuum and floor nozzle from the wand and check the wand for blockages.

Turn off vacuum and remove battery.
Remove the floor nozzle from the wand. Tilt neck of floor nozzle back to straighten the airway to remove blockages.

TROUBLE SHOOTING

To reduce the risk of shock and unintended operation, turn off power and remove the ION Power Pack before servicing.

Vacuum is not picking up debris, no suction or light suction.
(Refer to Maintenance section for more information.)

• Check filters to see if they need cleaning. Follow instructions for rinsing and completely air-drying the filters before reinserting in the vacuum.
• Dust cup may be full; empty dust cup.
• Check floor nozzle for blockages; clear blockages if required.
• Remove any string, carpet fibers, or hair that may be wrapped around the brushroll.
• Check connection between handvac and wand for blockages; clear blockages if required. If the issue persists, please contact Customer Service.

Vacuum lifts area rugs.

• Check that vacuum is in ION POWER mode. Take care when vacuuming area rugs or rugs with delicately sewn edges.
• Turn off the unit to disengage the brushroll and restart with the Power button.

Brushroll/Soft Roller does not spin.

• If Brushroll Indicator Light on the floor nozzle turns red, the brushroll has stopped spinning. Immediately turn off and remove ION Power Pack from handheld vacuum and remove any blockages before reconnecting and turning vacuum back on. If light turns green, the blockage has been successfully cleared. If the light remains red, please contact Customer Service.
• If headlights are not illuminated, there is a connection issue between the handheld vacuum, wand, and nozzle. Try disconnecting and reattaching the pieces. If the headlights still do not illuminate, please contact Customer Service.

Vacuum turns off on its own.

There are several possible reasons for the vacuum turning off on its own, including blockages, ION Power Pack issues, and overheating. If vacuum turns off on its own, perform the following steps:

1. Check LED lights on ION Power Pack to see if it needs to be recharged. If power pack does not need charging, turn off vacuum and remove power pack.
2. Empty dust cup and clean filters (see Maintenance section).
3. Check wand, accessories, and inlet openings and remove any blockages.
4. Allow unit and ION Power Pack to cool for at least 45 minutes, until it returns to room temperature.
5. Return power pack to vacuum and press Power button.

Note: If vacuum still does not operate properly, contact Customer Service.

LED lights on ION Power Pack are flashing.

• Bottom LED light is flashing (Fig. A): ION Power Pack needs to be charged.
• Top and bottom LED lights are flashing (Fig. B): ION Power Pack temperature is not optimal, so charging is temporarily paused. Leave power pack plugged in and charging will resume soon.
• If top 2 or bottom 2 LED lights are flashing (Fig. C, Fig. D), call Customer Service.

	LIGHT INDICATOR	WHAT IT MEANS
	FLOOR and CARPET icons alternate illuminating	Unit temperature is high. Turn off vacuum. While unit is cooling, look for blockages and remove any that are found. Filters may also need to be cleaned.
	ION POWER and ION BOOST icons are flashing together	Blockage detected. Turn off unit and remove blockage.
	Headlights are flashing	Debris caught in the brushroll. Turn off the vacuum, then remove debris. Garage door lid may not be properly closed Turn off the vacuum, and ensure the lid is properly clicked in on both sides.

For all other issues, please call Customer Service at 1-800-798-7398.