Soundcore 3 - Portable Bluetooth Speaker Manual

At a Glance

1. Power LED
2. Power button
3. Volume down button
4. Multi-function button
5. Volume up button
6. Bluetooth/PartyCast button
7. Bluetooth/PartyCast LED
8. USB-C charging port

Charging

• Fully dry off the USB port before charging.
• Use the provided USB-C cable to prevent any damage.
• Fully charge this speaker before the first use to prolong the lifespan of the built-in battery.
• Disconnect this speaker from the charger when fully charged. Do not charge for extended periods.

	Flashing red	Low battery
	Steady red	Being charged
	Steady white	Fully charged

Powering On/Off

Power on		Press
Power off		Press and hold for 2 seconds

• This speaker will power off automatically 30 minutes after no audio input or button inactivity.

Using your Device

Bluetooth Mode

With this speaker, you can enjoy music through your Bluetooth-enabled devices.

	Press	Enter Bluetooth pairing mode
	Flashing blue	Bluetooth pairing
	Steady blue	Bluetooth connected

• Dual Bluetooth Connection: This speaker can pair up to 2 mobile devices via Bluetooth. To pair with another device, press the Bluetooth button to re-enter Bluetooth pairing mode.
• This speaker can only play music on one mobile device at a time. To play from another connected device, pause the currently active device first.
• Each time you power on your Soundcore speaker, it will automatically connect to your last connected device if available within the Bluetooth range. If not, press the Bluetooth button to enter Bluetooth pairing mode.

PartyCast Mode

	Press and hold for 2 seconds	Enter PartyCast pairing mode
	Flashing white	PartyCast pairing
	Flashing white (Primary speaker)	PartyCast connected
	Steady white (Secondary speakers)

You can wirelessly connect up to 100 identical Soundcore 3 speakers together.

1. Press and hold the Bluetooth button for 2 seconds on the Soundcore 3 that's currently connected to your device as the primary speaker.
2. Repeat Step 1 on the other Soundcore 3 you want to connect and then press the Bluetooth button twice to make them secondary speakers in PartyCast pairing.
3. The secondary speakers will automatically connect with the primary speaker.

*Soundcore speakers with PartyCast function can be connected with Soundcore 3.

When PartyCast mode is successfully entered:

• Any secondary speaker can be switched to become the primary speaker by pressing the Blutooth button twice and connecting to your smartphone. Any primary speaker can be switched to become the secondary speaker by pressing the Bluetooth button twice and searching for an available primary speaker.
• To exit the PartyCast mode, press and hold the Bluetooth button on any speaker for 2 seconds.

Button Controls

	Press	Play/Pause
	Press twice	Next track
	Press three times	Previous track
	Press or press and hold	Adjust volume
	Press	Answer/End a call
	Press	Answer a second incoming call and put the current call on hold
	Press and hold for 2 seconds	Reject an incoming call
	Press and hold for 2 seconds	Switch between a call on hold and an active call
	Press and hold for 2 seconds	Activate Siri or other voice assistant software

Soundcore App

Download the Soundcore App for enhanced product experience.

• Check product information
• Update firmware
• Indicate battery status
• Remotely control the volume and play/pause
• Customize EQ settings
• Set Auto-power off time

Specifications

Specifications are subject to change without notice

DC power input	5V 2A
Battery capacity	6700 mAh
Audio output power	8Wx2
Charging time	Appr. 4 hours
Playtime (varies by volume level and music content)	Up to 24 hours
Waterproof level	IPX7
Bluetooth version	5.0
Bluetooth range	20 m/ 66 ft

Documents / Resources

Download manual

Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.

Download Soundcore 3 - Portable Bluetooth Speaker Manual