Table of Contents
Advertisement
en Meat probe
a When the time has elapsed, a signal sounds. A
message appears on the display confirming that the
operation has finished.
Once the cooking time has elapsed:
5.
If required, you can select other settings and re-
‒
start the operation.
When the food is ready, use
‒
pliance off.
Setting the end time
To achieve good cooking results, only change the set
time before the operation starts and before the cooking
time starts counting down.
Press "End time".
1.
Use
or
to change the time.
2.
Press "Apply".
3.
Cancelling the end time
You can delete the set time at any time.
Press "Stop"
1.
Press "End time"
2.
Use
to reset the time.
3.
Note: For operating modes that always require a
cooking time, the appliance resets the time at which
the cooking time ends to the next possible time.
Press "Start"
4.
10.3 Setting the timer
The timer runs independently during the operation. You
can set the timer when the appliance is switched on or
off, up to 24 hours. The timer has its own signal tone
so that you can tell whether it is the timer or a cooking
time that has elapsed.
Press the
button.
1.
11 Meat probe
Cook with precision by inserting the meat probe
the food and setting a core temperature on the appli-
ance. The meat probe measures the core temperature
inside the food. Once the set core temperature has
been reached in the food, the appliance automatically
stops heating.
11.1 Suitable types of heating with the meat
probe
Only certain types of heating are suitable for use with
the meat probe.
You can use the meat probe with the following types of
heating:
¡ 3D hot air
¡ Top/bottom heating
¡ Bottom heat
¡ Top/bottom heat gentle
¡ Hot air gentle
¡ Circulated air grilling
¡ Pizza setting
¡ Keeping warm
¡ Slow cooking
14
to switch the ap-
into
To set the timer, press the relevant time value on
2.
the display, e.g. hour display "h" or minute display
"min".
a The selected value is marked in blue.
Set the timer using
3.
ment bar.
If required, use
to reset the adjustment value.
To start the timer, press "Start".
4.
a The timer counts down.
a The timer remains visible on the display if the appli-
ance is switched off.
a When the appliance is switched on, the display
shows the settings for the current operation. The
timer is displayed in the status bar.
a Once the timer has elapsed, a signal tone sounds.
A note appears on the display confirming that the
timer has finished.
Changing the timer
You can change the timer at any time.
Press the
button.
1.
Press "Pause".
2.
Change the timer.
3.
Press "Start".
4.
Cancelling the timer
You can cancel the timer at any time.
Press the
button.
1.
Reset the timer using
2.
3.
Press "Start".
11.2 Inserting the meat probe
Use the meat probe supplied or order a suitable meat
probe from our customer service.
WARNING ‒ Risk of electric shock!
Using the wrong meat probe could damage the insula-
tion.
Only use the meat probe for this specific appliance.
▶
ATTENTION!
Otherwise the meat probe may be damaged.
Do not trap the cable of the meat probe.
▶
To prevent the meat probe from being damaged by
▶
excessive heat, there must be a gap of a few centi-
metres between the grill element and the meat
probe. The meat may expand during the cooking
process.
Note: If the pull-out rails are attached at level 3, you
cannot insert the roasting sensor in the cooking com-
partment. Unhook the pull-out rails or hook them in at a
different level.
→ "Rails", Page 27
Insert the meat probe into the food.
1.
or
or directly via the adjust-
.
Advertisement
Table of Contents
