Operation - Bosch BPC3200 Operating Instructions Manual

Operation

Start-up
Connecting the charger to the mains (see figure A)
Pay attention to the mains voltage. The voltage of the
u
power source must match the voltage specified on the
rating plate of the charger. Chargers marked 230 V can
also be operated at 220 V.
Plug the device connector (3) of the power cable into the
device socket (2) on the charger.
Connect the power cable (country-specific) to the mains.
Charging the Removed eBike Battery (see figures B–F)
Switch the eBike battery off and remove it from its holder on
the eBike. When doing so, read and observe the operating
instructions of the eBike battery.
Ensure the eBike battery is placed on clean surfaces
u
only. Avoid getting dirt, e.g. sand or soil, in the charging
socket and contacts in particular.
Plug the charging connector (5) of the charger into the char-
ging socket (6) on the eBike battery.
Charging the eBike Battery on the eBike
(see figures G−I)
Switch the eBike battery off. Clean the cover of the charging
socket (14). Avoid getting dirt, e.g. sand or soil, in the char-
ging socket and contacts in particular. Lift the cover of the
charging socket (14) and plug the charging connector (5)
into the charging socket (6).
There is a risk of fire due to the charger heating up
u
during charging. Ensure the eBike battery on the
eBike is completely dry and placed on a fireproof sur-
face before charging. If this is not possible, remove the
eBike battery from the holder and charge it in a more suit-
able location. When doing so, read and observe the oper-
ating instructions of the eBike battery.
Errors – causes and corrective measures
Cause
eBike battery defective
eBike battery too warm or too cold
Bosch eBike Systems
Charging process
The charging process begins as soon as the charger is con-
nected to the eBike battery or charging socket on the eBike
and to the mains.
Note: The charging process is only possible when the tem-
perature of the eBike battery is within the permitted char-
ging temperature range.
Note: The drive unit is deactivated during the charging pro-
cess.
The eBike battery can be charged with or without the on-
board computer. When charging without the on-board com-
puter, the charging procedure can be observed on the bat-
tery charge indicator (7) and, where applicable, on the oper-
ating unit.
When the on-board computer is connected, a charging noti-
fication appears on the display.
The state of charge is displayed by the battery charge indic-
ator (7) on the eBike battery, the operating unit and, where
applicable, the on-board computer.
The LEDs on the eBike battery charge indicator (7) flash dur-
ing the charging process. Each continuously lit LED repres-
ents approximately 20 % of the charging capacity. The flash-
ing LED indicates the next 20 % currently charging.
Once the eBike battery is fully charged, the LEDs go out im-
mediately and the on-board computer is switched off. The
charging process is terminated. The state of charge can be
displayed for 5 seconds by pressing the on/off button (8) on
the eBike battery.
Disconnect the charger from the mains and the eBike battery
from the charger.
When the battery is disconnected from the charger, the
eBike battery is automatically switched off.
Note: If you have charged the battery on the eBike, carefully
close the charging socket (6) with the cover (14) after char-
ging, so that no dirt or water can get in.
If the charger is not disconnected from the eBike battery
after charging, after a few hours the charger will switch itself
back on, check the state of charge of the eBike battery and
begin the charging procedure again if necessary.
Corrective measures
Two LEDs flash on the eBike battery.
Contact an authorised bike dealership.
Three LEDs flash on the eBike battery.
Disconnect the eBike battery from the charger until the char-
ging temperature range has been reached.
Do not reconnect the eBike battery to the charger until it has
reached the correct charging temperature.
English – 3
0 275 007 3CX | (27.02.2023)