Subscribe to Our Youtube Channel
Related Manuals for Sanotechnik BERGEN
Summary of Contents for Sanotechnik BERGEN
- Page 1 Infrared makes life more healthy Due to our continued product improvement, product illustrated on this instruction manual may vary slightly from the actual product.
- Page 2 Recommendations Read this manual carefully before using your sauna for the first time. We recommend you keep it in a safe place for future reference. • Wood is a living element, to maintain its original appearance, it is important to treat the outside of the wood against moisture. •...
- Page 3 Safety IMPORTANT : Please read the safety instructions carefully before installing and using your sauna cabin. They are essential for your safety, so please adhere strictly to them. Beware of hyperthermia, heat stroke or heat exhaustion which can be caused or aggravated by noncompliance with the safety instructions.
- Page 4 Description sauna...
- Page 5 Description sauna （1400x300x33mm）2x （426x398x30mm）2x （1800x93x30mm）2x （532x425x50mm）2x （1800x93x30mm）1x (990x585x40mm) 1x （1800x93x30mm）60x (535x585x40mm) 1x (1800x93x30mm）1x （520x330x65mm）2x （1758x575x30mm）1x （560x300x40mm）1x （1650x575x30mm）1x （378x300x40mm）2x (1758x952x30mm) 1x Barrel hoop （1404x80x20mm）1x （3000x1800mm）1x （1404x80x20mm）1x （1000x320mm ）60x (1574x488x30mm) 1x （250x50x45mm）1x (1758x783x30mm) 1x （350x50x45mm）1x (1574x488x30mm) 1x Sauna stove （1152x425x50mm）2x （177x80x30mm）1x...
- Page 6 Description sauna Hygrometer Water pan Explosion proof lampshade Hourglass Wooden spoon Cup plate Wooden barrel Ø5x50 Ø4x50 Ø4x30 Ø3x35 Ø4x12 Ø6x70 240x...
- Page 7 Read the assembly instructions carefully before starting. Choice of location Designed solely for exterior installation. Select a space: • In a dry area, on a flat stable surface that can support the weight of your sauna. • The height must be sufficient for you to reach the ceiling and carry out electrical connections and maintenance. •...
-
Page 8: Assemble Instructions
Assemble instructions Ø 5 x 50 20PCS Ø 3 x 35 2PCS Ø 5 x 50 18PCS The front and rear panels need to be assembled as a whole first. The front panel is divided into three parts on the left and right, and the rear panel is divided into three parts on the top and bottom. - Page 9 Assemble instructions Assemble steps Ø 5 x 50 2PCS Undersupport AD=BC AB=BD Front Each slat is numbered and labeled. The left side is L01 L02 L03..L38 from bottom to top; The right side is R01 R02 R03..R38 from bottom to top.
- Page 10 Assemble instructions Assemble steps Ø 5 x 50 4PCS Under slat The top Flat shall be temporarily installed as a fixed protective measure during installation.
- Page 11 Assemble instructions Assemble steps 1. The slats of the barrel body, please be placed tightly when installing, which is conducive to the top installation and tightness. Ø 3 x 35 32PCS Ø 3 x 35 32PCS 2. Screws (M3*35 64PCS ) are used to fix the slats L8-L23 and R8-R23, R8-R23 Slat the top slats are placed tightly, after forming a circle, the barrel...
- Page 12 Assemble instructions Assemble steps Stainless steel bands Ø 4 x 50 4PCS Ø 4 x 50 4PCS Footrest...
- Page 13 Assemble instructions Assemble steps The support of the inner and outer seat plates has been pre installed on the front and rear plates. The outer base plate needs another support frame, and the support frame locks the screws onto the Flat noodles. The inner base plate does not need another support frame.
- Page 14 The sauna stove is a universal cable connected to an external customer power supply. The wires of the lamp should be connected to the wiring base of the sauna stove and powered through the sauna stove. Sauna stove Sauna stove lamp line（3*0.75mm²）...
- Page 15 Waterproof cloth Asphalt shingle Ø 4 x 12 200PCS 1800mm...
- Page 16 Timer switch Thermostat switch 1. Heater Turn the timer switch to the ”on” section (section A in figure 2, 0–4 hours). The heater starts heating immediately. 2. Pre-setting Time (timed switch-on) Turn the timer switch to the ”pre-setting” section (section B in figure 2, 0–8 hours). The heater starts heating when the timer has turned the switch back to the ”on”...
-
Page 17: Maintenance
Maintenance Protection of wood Brush each exterior barrel slat and apply a wood stain when full assembly to protect the wood. This wood stain had to be renewed according to the recommendations of the product used Maintenance IMPORTANT : Disconnect the cabin’s power supply cable before undertaking any work. Problems identified Possible reasons Solutions...
Need help?
Do you have a question about the BERGEN and is the answer not in the manual?
Questions and answers