Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Ribao BC-35
Summary of Contents for Ribao BC-35
- Page 1 Currency Counter BC-35 User Manual...
-
Page 2: Table Of Contents
BC-35 User Manual V1.0 Contents Contents ..............................1 1. Machine Overview ..........................2 1.1 Safety Instruction .......................... 2 1.2 Installation Instruction ........................3 1.3 Machine & Accessories ......................... 4 1.4 Appearance ........................... 5 1.4.1 Front Appearance ....................... 5 1.4.2 Back Appearance ........................ 5 1.5 Technical Parameters ........................ -
Page 3: Machine Overview
BC-35 User Manual V1.0 1. Machine Overview 1.1 Safety Instruction This product is used for counting banknotes. Our company does not assume any responsibility for any loss arising from the application of this product for any purpose other than the above without our company's permission, and for any loss caused by any modification of this product not by our company or by any agents not authorized by our company.If you need to install or transport this product, please... -
Page 4: Installation Instruction
BC-35 User Manual V1.0 Do not bend the power cord excessively, or place heavy or sharp objects on top of the machine. Do not use this product in an excessively humid environment. Please avoid strong light and strong magnetic field interference. -
Page 5: Machine & Accessories
BC-35 User Manual V1.0 1.3 Machine & Accessories Machine Note guider(left) Right guider(right) User manual Power cable Clean brush... -
Page 6: Appearance
BC-35 User Manual V1.0 1.4 Appearance 1.4.1 Front Appearance Note Guider Hopper Display Stacker 1.4.2 Back Appearance Feed gap knob Handle Rear lid open RJ12:Connect button external display Serial port RS-232 Power jack Power switch... -
Page 7: Technical Parameters
BC-35 User Manual V1.0 1.5 Technical Parameters Dimension(W×L×H) 300mm×247mm×287mm Net Weight About 7KG Currency Support Single Power requirement AC 100V-240V 50/60Hz ±10% Counting Mode Piece counting with preset value Counting Speed L(900pcs/min)/M(1200pcs/min/H(1500 pcs/min) Counterfeit Detection UV,MG Other Detection Width Detection, Double Detection, Half Notes Detection... -
Page 8: Start-Up
BC-35 User Manual V1.0 1.6 Start-up Reminder: To ensure smooth counting please install the left and right Note Guider in the box. Please check below Figure 2. Figure 2 1) Take out the left Note Guider, install the click into the rail of the Note Guider, and press the Note Guider until you hear a clicking sound, it means the Note Guider is installed in position, as shown in the Figure 3. -
Page 9: Notes Placement
BC-35 User Manual V1.0 3) Connect the machine with power supply and turn on the machine, the machine will enter loading interface, showing the firmware version as below Figure 5, 202510 is the firmware version as an example. Then the machine will enter below main operation interface, as shown in Figure 6. -
Page 10: Counting Error Code
BC-35 User Manual V1.0 1.8 Counting error code Error code Cause Detect the back cover is opened and gives warning Hopper sensor is covered for 3S but no notes pass Notes jam in the passage Double notes detected Stacker is full... -
Page 11: Function Introduction
BC-35 User Manual V1.0 2. Function Introduction 2.1 Function Introduction 2.1.1 Display Interface and Touch Screen Description 1. Accumulation 2. Batch number 3. UV detection 4. MG detection 5. Medium speed 6. Automatic start 7. Amount 8. Quantity 9. Number of symbols Figure 8 2.1.2 Operating Instructions for Function Keys... -
Page 12: Manual/Automatic Counting Set
BC-35 User Manual V1.0 2.1.3 Manual/Automatic Counting Set Press “ ” key to switch between Auto and Manual mode. Auto Mode: There will be a sign of A. on the upper right corner after successful set, as shown in Figure 9. Put the banknotes on the hopper, the mahcine will count the banknotes automatically. -
Page 13: Cnt Mode
BC-35 User Manual V1.0 Figure 11 PS： 1) For the currency with denomination “1” a. Customer can turn on the detection according to actual need and start counting. b. Customer can turn off DD .etc function, then you can count the quantity for mixed denomination. -
Page 14: Counterfeit Detection Set
BC-35 User Manual V1.0 Figure 14 4) Press “CLEAR/ESC” key to exit main interface, press “BATCH” key to turn off the batch function, you can press “+1/CF” key to turn off UV detection and MG detection, as shown in Figure 15. After above setting you can count mixed demomination of banknotes, “26”... -
Page 15: Speed Set
BC-35 User Manual V1.0 Figure 18 Press “+1/CF” key three times, it will only activate UV detection, as shown in Figure 19. Figure 19 Press “+1/CF” key four times, i it will turn off both UV & MG detection, as shown in Figure 20. -
Page 16: Batch Set
BC-35 User Manual V1.0 Figure 21 2.1.8 Batch Set Press “BATCH” key to activate batch counting function, as shown in Figure 22. Figure 22 After successful setting, there will be a sign of B on the upper left corner, as shown in Figure 23. The default setting of batch number is 0, 10, 20, 50, 100. -
Page 17: Firmware Version Check
BC-35 User Manual V1.0 Figure 24 A) Put a batch of banknotes on the hopper, after counting or the stacker is full, the machine will show the total amount and quantity of this counting; remove the notes and put on the hopper again, continue counting, the amount and quantity on display will be accumilated. - Page 18 BC-35 User Manual V1.0 2.1.11.1 Batch setting If the default Batch number does not satisfy you, you can also set manually, the setting range is 0-200. 1) Press “SET” key to enter into setting interface, until the left corner shows “bAT” , as shown in Figure Figure 26 2) Press “START/ENTER”...
- Page 19 BC-35 User Manual V1.0 Figure 28 2.1.11.2 UV detection level setting The “UV” displayed at the left corner means UV detection level, the range is 0-3, 3 is the highest level and the default setting is level 2. If you want to adjust the detection level, please press “START/ENTER” key，at this moment the “UV”...
- Page 20 BC-35 User Manual V1.0 Figure 30 2.1.11.4 DD(size detection)detection level setting The “dd” displayed at the left corner means width detection level, the range is 0-3, 3 is the highest level and the default setting is level 2. If you want to adjust the detection level, please press “START/ENTER” key，at this moment the“dd”will blink.
- Page 21 BC-35 User Manual V1.0 Figure 32 2.1.11.6 Historical record check Press “SET” key to enter into setting interface until the left corner shows “CC”, and “824” means this machine has totally counted 824 pcs notes, as shown in Figure 33.
-
Page 22: Restore Factory Setting
BC-35 User Manual V1.0 If you want to turn off the buzzer, please press “START/ENTER” key, at this moment “bUZ” will blink. Press “ ” or ” ” to adjust it to be 0 or 1. After finish adjustment, press “START/ENTER” key to save, “bUZ”... -
Page 23: Maintenance Instruction
BC-35 User Manual V1.0 Figure 38 3. Maintenance Instruction 3.1 Firmware Upgrade The firmware upgrading is realized by serial port, before upgrading, please copy the mainboard firmware(.hex, for example, yancj.hex）into a special loader, (please do not change the file name or format). -
Page 24: Daily Clean Instruction
BC-35 User Manual V1.0 3.2 Daily Clean instruction Any dust, dirt or other substances sticking to the sensor will interfere with the normal operation of the sensor and cause erroneous counting results. Therefore, the sensor and roller shaft shall be cleaned with the attached cleaning tools as necessary every day. -
Page 25: Clean The Banknote Stacker Sensor
BC-35 User Manual V1.0 3.2.3 Clean the banknote stacker sensor As shown in the following Figure 41, clean the sensor with nylon brush or cleaning cloth. (ST) Stacker Sensor Figure 41 3.2.4 Clean the channel internal sensors 1) Pull the back cover in the direction shown in the Figure to open the back cover. - Page 26 BC-35 User Manual V1.0 Figure 43 3) Please use nylon brush to clean the Upper UV sensor and 3 IR tube on IR emission board. Figure 44...
-
Page 27: Common Faults And Corresponding Descriptions
BC-35 User Manual V1.0 Common Faults and Corresponding Descriptions In the process of using the machine, the machine may show abnormal state, resulting in abnormal operation, and the machine will display corresponding fault information. The following provides the phenomenon when the machine malfunctions. Please refer to the maintenance manual for specific handling methods.
Need help?
Do you have a question about the BC-35 and is the answer not in the manual?
Questions and answers