Related Manuals for Bort BHR-2000-SC
Summary of Contents for Bort BHR-2000-SC
- Page 1 BHR-2000-SC 98296075 User’s Manual ........2 Инструкция по эксплуатации ...8...
- Page 2 English Remove plug from the mains immediately if cable is damaged or cut SAFETY AND OPERATING INSTRUCTIONS Read instruction manual HIGH PRESSURE CLEANER Denotes risk of electric shock For your own safety and for the safety of others, please read these instructions carefully before using this ap- pliance.
-
Page 3: Safety Valve
● The cross-section of any extension cables used - ACCIDENT HAZARD. must be proportional to their length, i.e. the longer DO NOT leave the cleaner unattended. the extension cable, the greater the cross-section; - SHORT CIRCUIT HAZARD. cables with a protection level of “IPX5” must be DO NOT move the cleaner by pulling on the electrical used. -
Page 4: Pre-Operation
3. ASSEMBLY 1. pressure cleaner 2. water supply hose You will need a standard screw driver. 3. water connection 4. water inlet 5. high pressure tube 6. water outlet(backside) 7. spray gun 8. power supply * No. 2, 3, 8 are not included PRE-OPERATION ADJUSTING FAN PATTERN The angle of spray coming out of the lance may be ad-... -
Page 5: Operation
• Separate lance from gun. The surest way to avoid damaging surfaces is to follow • Rotate nozzle to the narrow stream setting. This these steps: opens up the fan blades. 1. Before triggering the gun, adjust the nozzle to a wide •... -
Page 6: Troubleshooting
ter to clear off any dirt or grime that may have collected 4. Final Rinse on the surface. This will allow your detergent to attack Start fi nal rinse at bottom an work upward. Make sure the deep down dirt that has worked its way into the you thoroughly rinse the surface and that all detergent cleaning surface. -
Page 7: Service And Maintenance
● Thermal safety has tripped. CLEANING - Leave the lance open with water comingthrough. Keep the ventilation slots of the machine clean to prevent overheating of the engine. Clean the housing 2. Fluctuating pressure regularly with a soft cloth, preferably every time it is ●... -
Page 8: Технические Характеристики
Немедленно выключите мойку в случае: 1. Неисправности или повреждения вилки или шну- ра питания. 2. Поломки выключателя. МОЙКА ВЫСОКОГО ДАВЛЕНИЯ 3. Появления дыма или запаха горелой изоляции. ЭЛЕКТРИЧЕСКАЯ 4. Повреждения шланга высокого давления. Перед началом работы: НАЗНАЧЕНИЕ ● Убедитесь в том, что вода поступает в мойку Данное... - Page 9 ствии со стандартом DIN 1988, моечные аппараты, 1. Мойка работающие по принципу водяной струи высокого 2. Шланг для подачи воды давления, разрешено подключать к сети питьевого 3. Подсоединение к источнику воды водопровода, если на подводящем шланге имеет- 4. Патрубок входной ся...
-
Page 10: Техническое Обслуживание И Уход
РАБОТА Примечание: После каждого применения моющего средства промойте емкость водой. При распылении воды на поверхность, максималь- ный эффект возникает, когда вода попадает на по- ВЫКЛЮЧЕНИЕ верхность под углом 90 градусов. Тем не менее, не 1. Отключите мойку при помощи выключателя . всегда... - Page 11 Exploded view BHR-2000-SC...
- Page 12 Spare parts list BHR-2000-SC No. Part Name Switch Gun high-pressure assy Electric motor Pump assy Set of gaskets Knob switch mode assy...
-
Page 13: Environmental Protection
ENVIRONMENTAL PROTECTION DECLARATION OF CONFORMITY Discarded electric appliances are recyclable and should not be We declare under our sole responsibility that this prod- discarded in the domestic waste! Please actively support us in uct is in conformity with the following standards or conserving resources and protecting the environment by standardized documents: EN 55014-1:2000+A1+A2;...
Need help?
Do you have a question about the BHR-2000-SC and is the answer not in the manual?
Questions and answers