Subscribe to Our Youtube Channel
Related Manuals for SUMERAIN S3230XI
Summary of Contents for SUMERAIN S3230XI
- Page 1 MODEL: S3230XI Version: V1.4 INSTALLATION GUIDE TUB AND SHOWER FAUCET MODEL FINISH S3230CI CHROME S3230NI BRUSHED NICKEL S3230OI OIL RUBBED BRONZE S3230GI BRUSHED GOLD S3230DI MATTE BLACK HOT LINE: +1-866-203-0866...
-
Page 2: Before Proceeding
Dear Valued Customer, SUMERAIN would like to take this opportunity to thank you for purchasing SUMERAIN products. It is our sincere hope that you are completely satisfied with your new purchase. All SUMERAIN products are carefully engineered, and factory tested to provide long trouble-free use under normal conditions. -
Page 3: Limited Lifetime Consumer Warranty
This warranty covers only your SUMERAIN manufactured product. SUMERAIN warrants this product against defects in material or workmanship as follows: SUMERAIN will repair at no charge for parts only or, at its option, replace any product or part of the product that proves defective because of improper workmanship and/or material, under normal installation, use, service and maintenance. - Page 4 FUNCTIONS AND SPECIFICATION Faucet type Tub and Shower Faucet Feature Concealed tub and shower faucet Theme Modern, Contemporary Mounting type Wall mount Number of Handles Metal Handles Material Handle style Lever Shower Arm Reach 11-5/16 Inch [288mm] Showerhead Width 195mm [7-11/16 Inch] Showerhead Length 195mm...
- Page 5 DEMENSION FRONT VIEW OF SHOWER...
- Page 6 SIDE VIEW OF SHOWER...
-
Page 7: Installation Steps
Aerator lock nut HPB59-1 FAE32300PB Screw cover PSA00002CH Tub spout HPB59-1 PSP32300CH Diverter cartridge ASSEMBLE PCT00001XX Anchor PSA00010XX Diverter sleeve HPB59-1 PSL32181CH Mounting screw SUS304 PSC00002XX If any of these items are missing, please contact SUMERAIN consumer service by email to: supports@sumerain.com. - Page 8 4. PLANNING AND INSTALLATION INSTRUCTIONS Attentions: The shower has to be installed, rinsed and checked in compliance with the applicable regulations in order to guarantee proper shower function! The dimensions of the shower set-up must be individually. Operating pressure at the control valve: Max.
- Page 9 Secure the concealed box assembly to the mounting rack with screws and anchor. 6. VALVE TRIM INSTALLATION 6.1 Turn on your shut-off valve for cleaning the hot and cold water supply pipe before connect to the valve body, allow the water flush 3~5 minutes to flush out dirt and debris.
- Page 10 6.2 Apply Teflon tape on the thread of pipe inlet and then connect to valve inlet with elbow [hot left, cold right]. Mixer Valve Connecting thread for Hot&Cold water Mixer Valve inlet thread: NPT1/2 (US, CA) G1/2” [1/2 BSPP] (UK, Europe etc.) Connect to valve outlet with elbow:...
- Page 11 6.3 Remove the valve sleeve by Phillips screwdriver. Turn on hot and cold water supply and check all connection for leaks Please shut off your hot and cold water supply again if no leaking. 6.4 Drill the mounting holes exactly according to mixer valve and elbow position, done the finish wall. Cut the plaster shield around the finish wall surface and seal the wall around the plaster shield with waterproof sealant WARNING: Failure to seal the wall can lead to possible water damage.
- Page 12 6.5 Remove the valve sleeve by Phillips screwdriver and hold the screw for next step.
- Page 13 6.6 Attach the escutcheon over the valve body. 6.7 Seal the wall around the plaster shield with waterproof sealant...
- Page 14 6.8 Attach handle onto the valve stem and tighten set screws by the Allen wrench that is provided. Please don’t over tighten. Done the same procedure on diverter knob. Finally press-in the screw cover. 6.9 Valve trim install finish.
- Page 15 7. SHOWERHEAD INSTALLATION 7.1 Attach Shower arm escutcheon to the shower arm and apply Teflon tape on the thread of shower arm, Secure the shower arm into the pipe elbow inside the wall by rotating clockwise. Standard thread of Shower arm inlet: NPT1/2 (US, CA)
- Page 16 7.2 Seal the wall around the shower arm escutcheon with waterproof sealant 7.3 Put the screen washer into the connector of showerhead and secure the showerhead on the shower head arm by hand rotating clockwise. Missing the screen washer might lead to shower invalid or damage.
- Page 17 8. TUB SPOUT INSTALLATION 8.1 Loose the set screws by Allen key and remove the spout nipple assembly from tub spout assembly. 8.2 Remove the aerator lock nut by adjustable wrench and disassemble all inside parts from the spout nipple supply.
- Page 18 8.3 Apply Teflon tape on the thread of spout nipple supply and screw the thread into the pipe elbow inside the wall. (S12mm) 8.4. Reinstall the aerator lock nut and all inside parts to the spout nipple supply by adjustable wrench.
- Page 19 8.5. Push the flange to tub spout from behind. 8.6. Docking the tub spout to the spout nipple supply and secure with set screw by Allen Key.
- Page 20 8.7. Attach the flange to finish wall. 8.8. Seal the wall around the flange with waterproof sealant.
- Page 21 8.9 Install finish. 9. INSPECTION 9.1 Turn on hot and cold water supply and check all connection for ensuring no leaking anywhere. 10. FUNCTION INSPECTION 10.1 Turn on the hot or cold knob respectively, the water outflow from the showerhead in turn. 10.2 Switch the diverter Knob, the water will rush from the tub spout.
- Page 22 Please note: if the surface is already damaged, the effect of cleaning materials will cause further damage. Components with damaged surfaces must be replaced or injury could result. Damage caused by improper treatment is not covered under the warranty. HONGKONG SUMERAIN SANITARY INDUSTRY CO., LIMITED Address: ROOM 1018, HOLLYWOOD PLAZA 610 NATHAN ROAD MONGKOK, KL,HONGKONG Factory Address: Floor 3th,No.2 ZhongXing Road,ShuiNuan City Industrial Zone,Shuikou town, Kaiping City,...
Need help?
Do you have a question about the S3230XI and is the answer not in the manual?
Questions and answers