THANK YOU Dear Valued Customer, SUMERAIN would like to take this opportunity to thank you for purchasing SUMERAIN products. It is our sincere hope that you are completely satisfied with your new purchase. All SUMERAIN products are carefully engineered, and factory tested to provide long trouble-free use under normal conditions. This product is easy to install using basic tools and our easy to follow illustrated instructions.
This warranty covers only your SUMERAIN manufactured product. SUMERAIN warrants this product against defects in material or workmanship as follows: SUMERAIN will repair at no charge for parts only or, at its option, replace any product or part of the product that proves defective because of improper workmanship and/or material, under normal installation, use, service and maintenance.
Page 4
Hand shower holder Material Brass Hand shower Material 200mm [7-7/8 Inch] Hand shower Height 35mm [1-3/8 Inch ] Hand shower width Net Weight 6,61lbs [3.0KG] Gross Weight 7,711lbs [3.5KG] Packing box [L x W x H] 11-7/32”(285mm)x10-13/16”(275mm)x7-7/8”(200mm) SUMERAIN SANITARY GROUP WWW.SUMERAIN.COM...
Page 5
DIMENSION FRONT VIEW OF SHOWER SUMERAIN SANITARY GROUP WWW.SUMERAIN.COM...
Page 6
SIDE VIEW OF SHOWER SUMERAIN SANITARY GROUP WWW.SUMERAIN.COM...
4 PCS 3223024 Set screw 1 PCS 3223025 Allen wrench 2.8mm 1 PCS 3223026 Screw cover 1 PCS If any of these items are missing, please contact SUMERAIN consumer service at +86-750-2731579 or email to: supports@sumerain.com SUMERAIN SANITARY GROUP WWW.SUMERAIN.COM...
Page 8
5. CONCEALED BOX ASSEMBLY INSTALLATION 5.1 Make a mounting rack (normally use woods as materials) for preparing install the concealed box assembly .the mounting board’s face should be Min 65mm [2-17/32"] and Max 90mm [3-17/32"] behind the finish wall surface. SUMERAIN SANITARY GROUP WWW.SUMERAIN.COM...
Page 9
6.1 Turn on your shut-off valve for cleaning the hot and cold water supply pipe before connect to the valve body, allow the water flush 3~5 minutes to flush out dirt and debris. Shut off the water supply again after finish. HOT WATER SUPPLY COLD WATER SUPPLY SUMERAIN SANITARY GROUP WWW.SUMERAIN.COM...
Page 10
6.2 Apply Teflon tape on the thread of pipe inlet and then connect to valve inlet with elbow [hot left, cold right]. Mixer Valve Connecting thread for Hot&Cold water Mixer Valve inlet thread: NPT1/2 (US, CA) G1/2” [1/2 BSPP] (UK, Europe etc.) Connect to valve outlet with elbow: SUMERAIN SANITARY GROUP WWW.SUMERAIN.COM...
Page 11
6.4 Drill the mounting holes exactly according to mixer valve and elbow position, done the finish wall. Cut the plaster shield around the finish wall surface and seal the wall around the plaster shield with waterproof sealant WARNING: Failure to seal the wall can lead to possible water damage. SUMERAIN SANITARY GROUP WWW.SUMERAIN.COM...
Page 12
6.5 Remove the valve sleeve by Phillips screwdriver and hold the screw for next step (fastening battery box). SUMERAIN SANITARY GROUP WWW.SUMERAIN.COM...
Page 13
6.6 Attach the escutcheon over the valve body. 6.7 Seal the wall around the plaster shield with waterproof sealant SUMERAIN SANITARY GROUP WWW.SUMERAIN.COM...
Page 14
6.8 Attach handle onto the valve stem and tighten set screws by the Allen wrench that is provided. Please don’t over tighten. Done the same procedure on diverter knob. Finally press-in the screw cover. 6.9 Valve trim install finish. SUMERAIN SANITARY GROUP WWW.SUMERAIN.COM...
Page 15
7.1 Attach Shower arm escutcheon to the shower arm and apply Teflon tape on the thread of shower arm, Secure the shower arm into the pipe elbow inside the wall by rotating clockwise. Standard thread of Shower arm inlet: NPT1/2 (US, CA) G1/2” [1/2 BSPP] (UK, Europe etc.) SUMERAIN SANITARY GROUP WWW.SUMERAIN.COM...
Page 16
7.2 Seal the wall around the shower arm escutcheon with waterproof sealant 7.3 Put the screen washer into the connector of showerhead and secure the showerhead on the shower head arm by hand rotating clockwise. Missing the screen washer might lead to shower invalid. SUMERAIN SANITARY GROUP WWW.SUMERAIN.COM...
Page 17
8.1 Apply Teflon tape on the thread of wall supply elbow and screw the thread into the pipe elbow inside the wall. 8.2 Attach the docking of hand shower holder to the wall and fasten by mounting screws. SUMERAIN SANITARY GROUP WWW.SUMERAIN.COM...
Page 18
8.3 Docking the hand shower holder to the dock and secure with set screw by Allen Key. 8.4. Connect the hand shower to the wall supply elbow with flexible hose. SUMERAIN SANITARY GROUP WWW.SUMERAIN.COM...
Page 19
9.1 Turn on hold and cold water supply and check all connection for ensuring no leaking anywhere. 10. FUNCTION INSPECTION 10.1 Turn on the handle, the water outflow from the showerhead. 10.2 Switch the diverter Knob, the water will rush from the hand shower. INSTALL FINISH SUMERAIN SANITARY GROUP WWW.SUMERAIN.COM...
Page 20
CLEARNING RECOMMENDATION FOR SUMERAIN PRODUCTS Modern lavatory faucets, kitchen faucets, and showers consist of very different materials to comply with the needs of the market with regard to design and functionality. To avoid damage and returns, it is necessary to consider certain criteria when cleaning.
SUMERAIN INTERNATIONAL GROUP – AMERICA Branch Address: 13455 Harper Dr. Saratoga, CA 95070 Tel: +1-408-867-8884 FAX: +1-408-867-4272 E-mail: us@sumerain.com SUMERAIN INTERNATIONAL GROUP – Verkaufsniederlassung in Deutschland [EUROPE] Adresse: Der Ecke,Moellendorffstr. 108, 10367 Berlin Deutschland Tel: +49 (0)30/23975898 E-mail: de@sumerain.com SUMERAIN SANITARY GROUP...
Need help?
Do you have a question about the S3223CI and is the answer not in the manual?
Questions and answers