Subscribe to Our Youtube Channel
Related Manuals for SUMERAIN S3218CI
Summary of Contents for SUMERAIN S3218CI
- Page 1 Version: V1.2 SHOWER SYSTEM MODEL FINISH S3218CI CHROME S3218NI BRUSHED NICKEL S3218OI OIL RUBBER BRONZE S3218BGI Brushed Gold HOT LINE: +1-866-203 0866...
- Page 2 Dear Valued Customer, SUMERAIN would like to take this opportunity to thank you for purchasing SUMERAIN products. It is our sincere hope that you are completely satisfied with your new purchase. All SUMERAIN products are carefully engineered, and factory tested to provide long trouble-free use under normal conditions. This product is easy to install using basic tools and our easy to follow illustrated instructions.
- Page 3 This warranty covers only your SUMERAIN manufactured product. SUMERAIN warrants this product against defects in material or workmanship as follows: SUMERAIN will repair at no charge for parts only or, at its option, replace any product or part of the product that proves defective because of improper workmanship and/or material, under normal installation, use, service and maintenance.
- Page 4 Faucet type Shower System Feature Concealed shower faucet Theme Modern, Contemporary Mounting type Wall mount Number of Handles Handles Material Metal Handle style Lever Shower Arm Reach 154mm [6-1/6 Inch] Showerhead Width 195mm [7-11/16 Inch] Showerhead Length 195mm [7-11/16 Inch] Valve Type Φ...
- Page 5 FRONT VIEW OF SHOWER...
- Page 6 SIDE VIEW OF SHOWER...
-
Page 7: Before Proceeding
Set screw 2 PCS 3218019 Allen wrench 2.8mm 1 PCS 3218020 Screw cover 1 PCS 3218021 Mounting screw 4 PCS 3218022 Anchor 4 PCS If any of these items are missing, please contact SUMERAIN consumer service by email to: supports@sumerain.com... - Page 8 4. PLANNING AND INSTALLATION INSTRUCTIONS Attentions: The shower has to be installed, rinsed and checked in compliance with the applicable regulations in order to guarantee proper shower function! The dimensions of the shower set-up must be individually. Operating pressure at the control valve: Max.
-
Page 9: Hot Water Supply
Secure the concealed box assembly to the mounting rack with screws and anchor. 6. VALVE TRIM INSTALLATION 6.1 Turn on your shut-off valve for cleaning the hot and cold water supply pipe before connect to the valve body, allow the water flush 3~5 minutes to flush out dirt and debris. - Page 10 6.2 Apply Teflon tape on the thread of pipe inlet and then connect to valve inlet with elbow [hot left, cold right]. Mixer Valve Connecting thread for Hot&Cold water inlet (NPT 1/2”) Connect to valve outlet with elbow:...
- Page 11 6.3 Remove the valve sleeve by Phillips screwdriver. Turn on hold and cold water supply and check all connection for leaks Please shut off your hot and cold water supply again if no leaking. 6.4 Done the finish wall and drill proper window for maintain if needs in the future.
- Page 12 6.5 Drill the mounting holes exactly according to mixer valve and elbow position, done the finish wall. Cut the plaster shield around the finish wall surface and seal the wall around the plaster shield with waterproof sealant WARNING: Failure to seal the wall can lead to possible water damage.
- Page 13 6.5 Remove the valve sleeve by Phillips screwdriver and hold the screw for next step (fastening battery box). 6.6 Attach the escutcheon over the valve body.
- Page 14 6.7 Seal the wall around the plaster shield with waterproof sealant 6.8 Attach handle onto the valve stem and tighten set screws by the Allen wrench that is provided. Please don’t over tighten. Done the same procedure on diverter knob. Finally press-in the screw cover.
- Page 15 6.9 Valve trim install finish. 7. SHOWERHEAD INSTALLATION 7.1 Attach Shower arm escutcheon to the shower arm and apply Teflon tape on the thread of shower arm, Secure the shower arm into the pipe elbow inside the wall by rotating clockwise. Standard thread of Shower arm inlet: NPT1/2 (US, CA) G1/2”...
- Page 16 7.2 Seal the wall around the shower arm escutcheon with waterproof sealant...
- Page 17 7.3 Put the screen washer into the connector of showerhead and secure the showerhead on the shower head arm by hand rotating clockwise. Missing the screen washer might lead to shower invalid. 8. HAND SHOWER INSTALLATION 8.1 Apply Teflon tape on the thread of nipple and screw the thread into the pipe elbow inside the wall.
- Page 18 8.2 Dock the shower holder assembly to nipple. 8.3 Secure shower holder to nipple with set screw by Allen Key.
-
Page 19: Function Inspection
8.4. Connect the hand shower to the elbow with flexible hose. 9. INSPECTION 9.1 Turn on hold and cold water supply and check all connection for ensuring no leaking anywhere. 10. FUNCTION INSPECTION 10.1 Turn on the handle, the water outflow from the showerhead. 10.2 Switch the diverter Knob, the water will rush from the hand shower. - Page 20 Please note: if the surface is already damaged, the effect of cleaning materials will cause further damage. Components with damaged surfaces must be replaced or injury could result. Damage caused by improper treatment is not covered under the warranty. HONGKONG SUMERAIN SANITARY INDUSTRY CO., LIMITED Address: ROOM 1018, HOLLYWOOD PLAZA 610 NATHAN ROAD MONGKOK, KL,HONGKONG...
Need help?
Do you have a question about the S3218CI and is the answer not in the manual?
Questions and answers