Related Manuals for SUMERAIN S3220CI-10
Summary of Contents for SUMERAIN S3220CI-10
- Page 1 Version: 1.2 INSTALLATION GUIDE CEILING SHOWER SYSTEM MODEL FINISH Showerhead S3220CI-10 CHROME 10 Inch S3220NI-10 BRUSHED NICKEL 10 Inch S3220OI-10 OIL RUBBER BRONZE 10 Inch S3220GI-10 GOLD 10 Inch SUMERAIN SANITARY GROUP WWW.SUMERAIN.COM...
-
Page 2: Before Proceeding
THANK YOU Dear Valued Customer, SUMERAIN would like to take this opportunity to thank you for purchasing SUMERAIN products. It is our sincere hope that you are completely satisfied with your new purchase. All SUMERAIN products are carefully engineered, and factory tested to provide long trouble-free use under normal conditions. This product is easy to install using basic tools and our easy to follow illustrated instructions. -
Page 3: Limited Lifetime Consumer Warranty
This warranty covers only your SUMERAIN manufactured product. SUMERAIN warrants this product against defects in material or workmanship as follows: SUMERAIN will repair at no charge for parts only or, at its option, replace any product or part of the product that proves defective because of improper workmanship and/or material, under normal installation, use, service and maintenance. - Page 4 Elbow Material Brass Hand shower holder Material Brass Hand shower Material 7-7/8(200mm) Hand shower Height 1-3/8”(35mm) Hand shower width Net Weight 9,47lbs [4.3KG] Gross Weight 10,6 lbs [4.8KG] Packing box [L x W x H] 11-7/32”(285mm)x10-13/16”(275mm)x7-7/8”(200mm) SUMERAIN SANITARY GROUP WWW.SUMERAIN.COM...
- Page 5 DIMENSION FRONT VIEW OF SHOWER SUMERAIN SANITARY GROUP WWW.SUMERAIN.COM...
- Page 6 SIDE VIEW OF SHOWER SUMERAIN SANITARY GROUP WWW.SUMERAIN.COM...
-
Page 7: Installation Steps
3220019 Allen wrench 2.8mm 1 PCS 3220020 Screw cover 1 PCS 3220021 Mounting screw 4 PCS 3220022 Anchor 4 PCS If any of these items are missing, please contact SUMERAIN consumer service by email to: supports@sumerain.com SUMERAIN SANITARY GROUP WWW.SUMERAIN.COM... - Page 8 5. CONCEALED BOX ASSEMBLY INSTALLATION 5.1 Make a mounting rack (normally use woods as materials) for preparing install the concealed box assembly .the mounting board’s face should be Min 55mm [2-5/32"] and Max 70mm [2-3/4"] behind the finish wall surface. SUMERAIN SANITARY GROUP WWW.SUMERAIN.COM...
- Page 9 6.1 Turn on your shut-off valve for cleaning the hot and cold water supply pipe before connect to the valve body, allow the water flush 3~5 minutes to flush out dirt and debris. Shut off the water supply again after finish. HOT WATER SUPPLY COLD WATER SUPPLY SUMERAIN SANITARY GROUP WWW.SUMERAIN.COM...
- Page 10 6.2 Apply Teflon tape on the thread of pipe inlet and then connect to valve inlet with elbow [hot left, cold right]. Mixer Valve Connecting thread for Hot&Cold water inlet (NPT 1/2”) Connect to valve outlet with elbow: SUMERAIN SANITARY GROUP WWW.SUMERAIN.COM...
- Page 11 6.4 Drill the mounting holes exactly according to mixer valve and elbow position, done the finish wall. Cut the plaster shield around the finish wall surface and seal the wall around the plaster shield with waterproof sealant WARNING: Failure to seal the wall can lead to possible water damage. SUMERAIN SANITARY GROUP WWW.SUMERAIN.COM...
- Page 12 6.5 Remove the valve sleeve by Phillips screwdriver and hold the screw for next step (fastening battery box). SUMERAIN SANITARY GROUP WWW.SUMERAIN.COM...
- Page 13 6.6 Attach the escutcheon over the valve body. 6.7 Seal the wall around the plaster shield with waterproof sealant SUMERAIN SANITARY GROUP WWW.SUMERAIN.COM...
- Page 14 6.8 Attach handle onto the valve stem and tighten set screws by the Allen wrench that is provided. Please don’t over tighten. Done the same procedure on diverter knob. Finally press-in the screw cover. 6.9 Valve trim install finish. SUMERAIN SANITARY GROUP WWW.SUMERAIN.COM...
- Page 15 7. SHOWERHEAD INSTALLATION 7.1 Attach Shower arm escutcheon to the shower arm and apply Teflon tape on the thread of shower arm SUMERAIN SANITARY GROUP WWW.SUMERAIN.COM...
- Page 16 7.2 Secure the shower arm into the pipe fitting inside the ceiling by rotating clockwise. Standard thread of Shower arm inlet: NPT1/2 (US, CA) G1/2” [1/2 BSPP] (UK, Europe etc.) 7.3 Attach the escutcheon to the ceiling and seal with waterproof sealant SUMERAIN SANITARY GROUP WWW.SUMERAIN.COM...
- Page 17 Missing the screen washer might lead to LED lighting shower invalid when installation LED showerhead. 8. HAND SHOWER INSTALLATION 8.1 Apply Teflon tape on the thread of nipple and screw the thread into the pipe elbow inside the wall. SUMERAIN SANITARY GROUP WWW.SUMERAIN.COM...
- Page 18 8.2 Dock the shower holder assembly to nipple. 8.3 Secure shower holder to nipple with set screw by Allen Key. SUMERAIN SANITARY GROUP WWW.SUMERAIN.COM...
- Page 19 8.4. Connect the hand shower to the elbow with flexible hose. SUMERAIN SANITARY GROUP WWW.SUMERAIN.COM...
-
Page 20: Troubleshooting
10.2 Switch the diverter Knob, the water will rush from the hand shower. INSTALL FINISH CLEARNING RECOMMENDATION FOR SUMERAIN PRODUCTS Modern lavatory faucets, kitchen faucets, and showers consist of very different materials to comply with the needs of the market with regard to design and functionality. - Page 21 HONGKONG SUMERAIN SANITARY INDUSTRY CO..LIMITED Address: ROOM 1018, HOLLYWOOD PLAZA 610 NATHAN ROAD MONGKOK, KL,HONGKONG Factory Address:25 building Tangkou Industrial Park,Shuikou town, Kaiping City, Guangdong Province, China Factory Tel: +86-750-2731579 Web: http://www.sumerain.com supports@sumerain.com E-mail: SUMERAIN AMERICA SUPPORT Address: Pershing Rd Chicago IL 60632...
Need help?
Do you have a question about the S3220CI-10 and is the answer not in the manual?
Questions and answers