Table of Contents
Advertisement
en Before using for the first time
7 Before using for the first time
Implement the settings for the initial configuration. Calibrate the appliance. Clean the appliance and accessories.
7.1 Before using for the first time
Before using the appliance for the first time, ask your
water supplier about the hardness of your tap water. To
ensure that the appliance can reliably remind you to
descale it when required, you must set your water hard-
ness range correctly.
ATTENTION!
If the wrong water hardness has been set, the appli-
ance cannot remind you to descale it at the right time.
▶
Set the water hardness correctly.
Using unsuitable liquids may damage the appliance.
▶
Do not use distilled water, highly chlorinated tap wa-
ter (>40 mg/l) or other liquids.
▶
Only use cold, fresh tap water, softened water or
non-carbonated mineral water.
Setting
1
0 (softened)
1 (soft)
2 (moderately hard)
3 (hard)
2
4 (very hard)
1
Only set this if you will be using solely softened water.
2
Also set for mineral water. Only use non-carbonated mineral water.
7.2 Carrying out the initial configuration
When the appliance is connected to the electricity sup-
ply for the first time or following a lengthy power cut,
you must configure the settings before you can use it. It
may take a few seconds for the settings to appear on
the display.
Note: You can also enter the settings using the Home
Connect assistant. In this case, press
last point in the initial configuration. If your appliance is
connected, follow the instructions in the app.
Setting the language
1.
Use the rotary selector to select the required lan-
guage.
2.
Press
.
a The next setting appears.
Setting the time
1.
Turn the rotary selector to set the current time.
2.
Press
.
a The next setting appears.
Setting the date
1.
Use the rotary selector to set the current day.
2.
Press
.
3.
Use the rotary selector to set the current month.
4.
Press
.
5.
Use the rotary selector to set the current year.
12
Malfunctions may occur when using filtered or deminer-
alised water. The appliance may request that you top
up the water tank even though it may be full, or opera-
tion with steam is cancelled after approx. two minutes.
▶
Tip: If you use mineral water, set the water hardness
range to "very hard". If you use mineral water, you must
only use non-carbonated mineral water.
Tip: If your tap water is very hard, we recommend that
you use softened water. If you use only softened water,
you can set your appliance to the "softened" water
hardness range.
Water hardness in
mmol/l
-
Up to 1.5
1.5-2.5
2.5-3.8
Above 3.8
6.
a The next setting appears.
Setting the water hardness
1.
2.
a A notification appears on the display confirming that
to go to the
7.3 Calibrating and cleaning the appliance
before using it for the first time
Calibrate the appliance and clean the cooking compart-
ment and accessories before using it to prepare food
for the first time.
Note: The boiling point of water depends on the air
pressure. During calibration, the appliance self-adjusts
during the first steam operation to the pressure ratio at
the installation location.
Do not open the appliance door while calibration is in
progress, as this will cancel the calibration process.
Requirement: The cooking compartment is cold or at
room temperature.
1.
2.
If required, mix filtered or demineralised water with
the bottled non-carbonated mineral water with a ra-
tio of one to one.
German hardness in
°dH
-
Up to 8.4
8.4-14
14-21.3
Above 21.3
Press
.
Use the rotary selector to set the hardness.
Press
.
the initial configuration is complete.
Remove the product information and the accessor-
ies from the cooking compartment. Remove any
leftover packaging, such as polystyrene pellets, and
any adhesive tape either in or on the appliance.
Wipe the smooth surfaces in the cooking compart-
ment with a soft, damp cloth.
French hardness °fH
-
Up to 15
15-25
25-38
Above 38
Advertisement
Table of Contents
