Sony EVI-HD1 Technical Manual page 28

EVI-HD1 Command List (3/3)
Command Set Command
CAM_IDWrite
IR_Receive On
Off
On/Off
IR_ReceiveReturn On
Off
D-SUB 15Pin SYNC 3-STATE
VD
Information Display On
Off
3)
Pan-tiltDrive Up
Down
Left
Right
UpLeft
UpRight
DownLeft
DownRight
Stop
AbsolutePosition
RelativePosition
Home
Reset
Pan-tiltLimitSet LimitSet
LimitClear
1) After an ACK to a One Push White Balance Trigger is sent until the operation is completed, "Not Executable" is sent as a reply when any
other commands are received.
When a slow shutter speed (1/20, 1/25 or lower) is selected, the time needed for the One Push White Balance adjustment will be longer.
2) Bright can be set only in Full Auto mode or Shutter Priority mode.
3) When the menu is displayed, this operation is ignored.
4) When other commands are received after a Completion notification for the Recall command is sent, "Command not executable" may be
returned for a maximum of 240 msec due to internal processing. In this case, please transmit the command again.
Command Packet
8x 01 04 22 0p 0q 0r 0s FF
8x 01 06 08 02 FF
8x 01 06 08 03 FF
8x 01 06 08 10 FF
8x 01 7D 01 03 00 00 FF
8x 01 7D 01 13 00 00 FF
8x 01 7E 01 1A 00 00 FF
8x 01 7E 01 1A 00 01 FF
8x 01 7E 01 18 02 FF
8x 01 7E 01 18 03 FF
8x 01 06 01 VV WW 03 01 FF
3)
8x 01 06 01 VV WW 03 02 FF
3)
8x 01 06 01 VV WW 01 03 FF
3) 8x 01 06 01 VV WW 02 03 FF
3)
8x 01 06 01 VV WW 01 01 FF
3)
8x 01 06 01 VV WW 02 01 FF
3)
8x 01 06 01 VV WW 01 02 FF
3) 8x 01 06 01 VV WW 02 02 FF
3) 8x 01 06 01 VV WW 03 03 FF
8x 01 06 02 VV WW
0Y 0Y 0Y 0Y 0Z 0Z 0Z 0Z FF
8x 01 06 03 VV WW
0Y 0Y 0Y 0Y 0Z 0Z 0Z 0Z FF
8x 01 06 04 FF
8x 01 06 05 FF
8x 01 06 07 00 0W
0Y 0Y 0Y 0Y 0Z 0Z 0Z 0Z FF
8x 01 06 07 01 0W
07 0F 0F 0F 07 0F 0F 0F FF
Comments
pqrs: Camera ID (=0000 to FFFF)
IR(remote commander) receive ON/OFF
IR (remote commander) receive message via the VISCA
communication ON/OFF
For contents of messages, see page 30.
Setting the sync of the HD analog component output
ON/OFF of the Operation status display of One Push
Trigger of CAM_Memory and CAM_WB
VV: Pan speed 0 x01 (low speed) to 0 x18 (high speed)
WW: Tilt Speed 0 x 01 (low speed) to 0 x14 (high speed)
YYYY: Pan Position FA60 to 05A0 (center 0000)
ZZZZ: Tilt Position FE98 to 0168 (center 0000)
See page 37.
W: 1 UpRight 0: DownLeft
YYYY: Pan Limit Position FA60 to 05A0 (center 0000)
ZZZZ: Tilt Position FE98~0168 (center 0000)
Command List
28