Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for HP 850 Unified Wired-WLAN Appliance
Summary of Contents for HP 850 Unified Wired-WLAN Appliance
- Page 1 HP 850 Unified Wired-WLAN Appliance Installation Guide...
- Page 2 The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services. Nothing herein should be construed as constituting an additional warranty.
-
Page 3: Table Of Contents
Contents Preparing for installation ················································································································································· 1 Safety recommendations ·················································································································································· 1 Safety symbols ·························································································································································· 1 General safety recommendations ··························································································································· 1 Electrical safety ························································································································································· 2 Laser safety ································································································································································ 2 Examining the installation site·········································································································································· 2 Temperature and humidity ······································································································································· 2 Cleanness ·································································································································································· 3 Cooling ······································································································································································... - Page 4 Displaying detailed information about the device ································································································ 2 Displaying the electronic label data for the device ······························································································ 2 Displaying the CPU usage of the device················································································································ 3 Displaying the memory usage of the device ········································································································· 3 Displaying the operational status of the built-in fans ···························································································· 4 Displaying the operating state of a power supply ································································································...
-
Page 5: Preparing For Installation
Preparing for installation IMPORTANT: For regulatory identification purposes, the HP 850 Unified Wired-WLAN Appliance and the HP 850 Unified Wired-WLAN TAA-Compliant Appliance are assigned a regulatory model number (RMN) BJNGA-FA0004. This regulatory number should not be confused with the marketing name HP 850, or product code JG722A and JG724A. -
Page 6: Electrical Safety
To prevent condensation, unpack the device at least half an hour after you move the device from a • location below 0°C (32°F) to the equipment room, and power on the device at least 2 hours after you move the device from a location below 0°C (32°F) to the equipment room. Electrical safety •... -
Page 7: Cleanness
Table 1 Temperature/humidity requirements in the equipment room Temperature Relative humidity 0°C to 45°C (32°F to 113°F) 5% to 95%, noncondensing Cleanness Dust buildup on the chassis can result in electrostatic adsorption, which causes poor contact of metal components and contact points, especially when indoor relative humidity is low. In the worst case, electrostatic adsorption can cause communication failure. -
Page 8: Esd Prevention
ESD prevention To prevent electrostatic discharge (ESD), follow these guidelines: Ground the device correctly. • Take dust-proof measures for the equipment room. For more information, see "Cleanness." • Maintain the humidity and temperature at acceptable levels. For more information, see •... -
Page 9: Lightning Protection
Capacitive coupling • Inductive coupling • Radiative coupling • • Common impedance coupling Conductive coupling • To prevent EMI, take the following actions: Use a socket with three pins and PE wire to prevent interference from the power grid. • Use a grounding system and a lightning protection system for the device separate from those for •... -
Page 10: Pre-Installation Checklist
Pre-installation checklist Table 4 Pre-installation checklist Item Requirements Result • There is a minimum clearance of 10 cm (3.9 in) around the inlet and exhaust vents for heat dissipation of the Ventilation device chassis. • A ventilation system is available at the installation site. Temperature 0°C to 45°C (32°F to 113°F) Relative humidity... - Page 11 Item Requirements Result • The device is far away from any moist area and heat source. Safety precautions • You have located the emergency power switch in the equipment room. Accessories Accessories provided with the device. • Documents shipped with the device. Reference •...
-
Page 12: Installing The Device
WARNING! Keep the tamper-proof seal on a mounting screw on the chassis cover intact, and if you want to open the chassis, contact HP Support for permission. Otherwise, HP will not be liable for any consequence caused thereby. Confirming installation preparations Before you install the device, verify that you have read "Preparing for installation"... -
Page 13: Mounting The Device On A Workbench
Mounting the device on a workbench If a standard 19-inch rack is not available, you can mount the device on a clean, flat workbench, as follows: Clean the recessed areas on the chassis bottom. Attach the four rubber feet to the recessed areas on the chassis bottom. Place the device on the workbench. - Page 14 Use a mounting bracket to mark cage nut installation positions on the two front rack posts. Make sure the cage nuts on the rack posts are at the same level. Install cage nuts to the marked positions on the rack posts. Figure 5 Installing cage nuts Use the screws packed with the mounting brackets to secure the mounting brackets to both sides of the device.
-
Page 15: Installing The Device By Using Mounting Brackets And A Rack Shelf
Figure 7 Installing the device in the rack Installing the device by using mounting brackets and a rack shelf The rack shelf is an optional component that needs to be separately ordered if needed. The rack shelf in this example is for illustration only. To install the device by using mounting brackets and a rack shelf: Wear the ESD wrist strap and make sure the rack is correctly grounded and sturdy enough. -
Page 16: Installing The Device By Using Mounting Brackets And Slide Rails
Push the device to the rack along the rack shelf, and attach the mounting brackets on the device to the front rack posts by using screws and cage nuts. Figure 9 Installing the device to the rack Installing the device by using mounting brackets and slide rails The slide rails are optional components that need to be separately ordered if needed. -
Page 17: Grounding The Device
Figure 10 Installing slide rails Holding both sides of the device, push the device to the rack along the slide rails. Make sure the chassis bottom makes close contact with the slide rails. Figure 11 Installing the device to the rack Attach the mounting brackets on the device to the front rack posts with M6 screws and cage nuts. - Page 18 To ground the device: Use a Phillips screwdriver to remove the grounding screw from the chassis. Use the grounding screw to attach the ring terminal of the grounding cable to the chassis. Connect the other end of the grounding cable according to the grounding method you use: Grounding the device with a grounding strip—If a grounding strip is available at the ...
- Page 19 Figure 13 Grounding the device with the rack (1)
- Page 20 Figure 14 Grounding the device with the rack (2) Grounding the device with a grounding conductor buried in the earth—If earth is available at the installation site, hammer a 0.5 m (1.64 ft) or longer angle iron or steel tube into the earth to serve as a grounding conductor.
-
Page 21: Connecting The Console Cable And Setting Terminal Parameters
Connecting the console cable and setting terminal parameters Connecting the console cable Prepare a configuration terminal. The configuration terminal can be an ASCII terminal with an RS232 serial port or a PC. The description in this section assumes that you use a PC as the configuration terminal. Connect the console cable: Plug the DB-9 female connector of the console cable to the serial port of the PC. - Page 22 Figure 17 Connection description Select the serial port to be used from the Connect using list, and click OK. Figure 18 Setting the serial port used by the HyperTerminal connection Set Bits per second to 9600, Data bits to 8, Parity to None, Stop bits to 1, and Flow control to None, and click OK.
- Page 23 Figure 19 Setting the serial port parameters Select File > Properties in the HyperTerminal window. Figure 20 HyperTerminal window On the Settings tab, set the emulation to VT100 and click OK.
-
Page 24: Connecting The Ethernet Cables
Figure 21 Setting the terminal emulation in Test Properties dialog box Connecting the Ethernet cables Connecting a copper Ethernet port Connect one end of the Ethernet cable to the copper Ethernet port of the device, and the other end to the Ethernet port of the peer device. After powering on the device, examine the LEDs of the fixed copper Ethernet port. -
Page 25: Installing A Power Supply
Make sure the Tx and Rx ports on a transceiver module are correctly connected. • To connect the device to the network through an optical fiber: Remove the dust plug on the fiber port. Remove the dust cover from the transceiver module, and insert the transceiver module into the fiber port. -
Page 26: Connecting The Ac Power Cord
Holding the handle of the power supply with one hand and supporting the bottom of the power supply with another hand, push the power supply into the slot along the guide rails until the power supply is completely inserted. Use a Phillips screwdriver to fasten the screws on the power supply. Figure 23 Installing an AC power supply Figure 24 Installing a DC power supply Connecting the AC power cord... -
Page 27: Connecting The Dc Power Cord
Figure 25 Connecting an AC power cord Connecting the DC power cord Use a flat-blade screwdriver to remove the protection cover from the DC power supply. Correctly insert the DC plug into the DC power receptacle. Use a flat-blade screwdriver to fasten the screws on the DC plug. Use a cable tie to secure the DC power cord to the handle of the DC power supply. -
Page 28: Verifying The Installation
Press Ctrl+D to access BASIC-BOOTWARE MENU Press Ctrl+T to start heavy memory test Booting Normal Extend BootWare..The Extend BootWare is self-decompressing..Done! **************************************************************************** HP 850 Unified Wired-WLAN JG722A BootWare, Version 1.05 **************************************************************************** Compiled Date : Aug 14 2013 CPU Type... - Page 29 Retrieving configuration file failed! User interface con0 is available. Press ENTER to get started. Press Enter at the prompt, and you can configure the device when the prompt <HP> appears. During the startup process, the CPLD is automatically upgraded to the latest version.
-
Page 30: Troubleshooting
• The power cord is in good condition. • If the problem persists, contact HP Support. Configuration terminal problems If the configuration environment setup is correct, the configuration terminal displays booting information when the device is powered on. If the setup is incorrect, the configuration terminal either displays nothing or displays garbled text. -
Page 31: Login Password Loss
Login password loss CAUTION: Dealing with console login password loss and user privilege level password loss from BootWare menus is disruptive. How to deal with console login password loss and user privilege level password loss depends on the state of password recovery capability (see Figure 27). -
Page 32: Dealing With User Privilege Level Password Loss
Restart the AC, and set a new password. <HP>system-view [HP]user-interface console 0 [HP-ui-console0]authentication-mode password [HP-ui-console0]set authentication password cipher 123456 Save the new configuration by using the save command. <HP> save Dealing with user privilege level password loss Select 8 from the BootWare menu to clear the user privilege level password. - Page 33 When you use FTP to load software, you entered an incorrect IP address, software name, username, • or password. If software loading has failed even if the physical connections are in good condition and the software loading process does not have any input errors, contact HP Support.
-
Page 34: Hardware Management And Maintenance
HP Comware Platform Software Comware Software, Version 5.20.109, ESS 2607P14 Copyright (c) 2010-2013 Hewlett-Packard Development Company, L.P. HP 850 uptime is 0 week, 0 day, 0 hour, 36 minutes HP 850 with 1 RMI XLP 432 1400MHz Processor 4096M bytes DDR3... -
Page 35: Displaying Detailed Information About The Device
88cd88 STMR 89a6f2 … Displaying detailed information about the device Use the display device verbose command to display detailed information about the device. <HP>display device verbose Slot No. Subslot No. Board Type Status Max Ports Normal Table 5 Command output... -
Page 36: Displaying The Cpu Usage Of The Device
CPU usage at the interval of 5 minutes). Displaying the memory usage of the device Use the display memory command to display the memory usage statistics for the device. <HP> display memory System Total Memory(bytes): 2345512880 Total Used Memory(bytes): 325207652... -
Page 37: Displaying The Operational Status Of The Built-In Fans
Used Rate Memory usage of the device. Displaying the operational status of the built-in fans Use the display fan command to display the operating states of fans. <HP>display fan 1 State: Normal 2 State: Normal 3 State: Normal Table 9 Command output... -
Page 38: Displaying The Exception Handling Method
Schedule a reboot at the CLI to occur at a specific time and date or after a delay. • • Power off and then power on the device again. Because this method can cause data loss, HP recommends that you use one of the CLI methods. To reboot the device immediately:... - Page 39 Task Command Remarks • Schedule a reboot to occur at a specific Use either command. time and date: The scheduled reboot function is schedule reboot at hh:mm [ date ] Schedule a reboot. disabled by default. • Schedule a reboot to occur after a delay: Available in user view.
-
Page 40: Appendix A Chassis Views And Technical Specifications
Appendix A Chassis views and technical specifications The figures in this document are for illustration only. Chassis views Figure 28 Front view (1) 100/1000Base-T autosensing Ethernet ports 1 to 8 (2) 100Base-FX/1000Base-X SFP ports 1 to 8 (combo interface) (combo interface) (3) 10GBase-R SFP+ ports (9 to 10) (4) 100/1000 Base-T management Ethernet ports (5) Console port... -
Page 41: Power Supply Views
Power supply views AC power supply Figure 30 AC power supply (1) Captive screw (2) Power receptacle DC power supply Figure 31 DC power supply (1) Captive screw (2) Power receptacle Transceiver module, fiber connector, and optical fiber views Use an SFP or SFP+ transceiver module together with an optical fiber with LC-type fiber connector. -
Page 42: Technical Specifications
Figure 32 SFP transceiver module Figure 33 SFP+ transceiver module Figure 34 Optical fiber with LC-type connectors (1) LC-type connector (2) Optical fiber Technical specifications Table 11 Technical specifications Item Specification Console port One, 9600 bps (default) to 115200 bps Eight 100/1000 Base-T autosensing Ethernet ports (copper Gigabit Ethernet port ports of a combo interface) -
Page 43: Transceiver Module Specifications
Item Specification SFP+ port Two 10GBase-R SFP+ ports Memory 2 × 2 GB DDR3 Storage media 4 GB CF card Dimensions (H × W × D) (without rubber feet and 43.6 × 440 × 420 mm (1.72 × 17.32 × 16.54 in) mounting brackets) Rate AC voltage range 100 VAC to 240 VAC @ 50 Hz or 60 Hz... - Page 44 Item Specification Fiber diameter 50 µm Transmit power –19 to –14 dBm Receive sensitivity ≤ –30 dBm Saturation ≤ –14 dBm Table 15 SFP-FE-LX-SM1310-A specifications Item Specification Central wavelength 1310 nm Transmission distance 15 km (9.32 miles) Transmission rate 125 Mbps Connector type Duplex LC Fiber mode...
- Page 45 Item Specification Fiber diameter 50 µm Transmit power –9.5 to 0 dBm Receive sensitivity ≤ –17 dBm Saturation ≤ –3 dBm Table 18 SFP-GE-LX-SM1310-A specifications Item Specification Central wavelength 1310 nm Transmission distance 10 km (6.21 miles) Transmission rate 1250 Mbps Connector type Duplex LC Fiber mode...
- Page 46 Item Specification Fiber diameter 9 µm Transmit power –4 to +1 dBm Receive sensitivity ≤ –21 dBm Saturation ≤ –3 dBm Table 21 SFP-GE-LH70-SM1550 specifications Item Specification Central wavelength 1550 nm Transmission distance 70 km (43.50 miles) Transmission rate 1250 Mbps Connector type Duplex LC Fiber mode...
-
Page 47: Interface Arrangement
Item Specification Fiber diameter 62.5 µm Transmit power –6.5 to +0.5 dBm Receive sensitivity ≤ –6.5 dBm Saturation ≤ 1.5 dBm Table 24 SFP-XG-LX-SM1310 specifications Item Specification Central wavelength 1310 nm Transmission distance 10 km (6.21 miles) Transmission rate 10.3125 Gbps Connector type Duplex LC Fiber mode... - Page 48 Ten-GigabitEthernet 1/0/9 and Ten-GigabitEthernet 1/0/10—10GBase-R SFP+ ports. You can • identify an interface by its mark. NOTE: A combo interface is a logical interface that contains a fiber port and a copper port. Only one of the two ports can be activated at a time. By default, the copper port is activated.
-
Page 49: Appendix B Leds
Appendix B LEDs LEDs Figure 35 LEDs (1) 100/1000Base-T autosensing Ethernet port status LEDs (2) 100Base-FX/1000Base-X SFP port status LEDs (3) 10GBase-R SFP+ port status LEDs (4) 100/1000 Base-T out-of-band management Ethernet port status LEDs (LINK/ACT) (5) Power supply 1 status LED (PWR1) (6) Power supply 2 status LED (PWR2) (7) System status LED (SYS) (8) Expansion slot status LED (MOD) - Page 50 Mark Status Description Flashing green The hard disk is reading or writing data. Steady yellow A failure has occurred. No interface card is present. No link is present. 100/1000 Base-T out-of-band LINK/ Steady green A link is present. management Ethernet port status LED (green) Flashing green The port is receiving or transmitting data.