Subscribe to Our Youtube Channel
Related Manuals for Daewoo DBP1800
Summary of Contents for Daewoo DBP1800
- Page 1 DBP1800/DBP2500 SUBMERSIBLE WATER PUMP/ USER‘S MANUAL Manufactured under license of Daewoo International Corporation, Korea Daewoo International Corporation, Korea...
-
Page 2: Table Of Contents
INDEX 1. IMPORTANT SAFETY INTRUCTION ....................... 3 2. SYMBOLS ............................. 4 3. PRODUCT INTRODUCTION ........................ 5 4. OPERATING CONDITIONS ........................5 5. INSTALLATION AND NOTICE POINTS ..................... 5 6. MACHINE DESCRIPTION........................6 7. TECHNICAL SPECIFICATION........................7 8. DESCRIPTION OF PARTS........................7 9. TROUBLESHOOTING ..........................8 10. -
Page 3: Important Safety Intruction
1. IMPORTANT SAFETY INSTRUCTION Read the instruction manual attentively before use. Keep the product in a dry place. Read all warnings and instructions attentively. Failure to follow all warnings and instructions listed below may result in electric shock, fire and/or serious personal injury. Read operator`s manual carefulle. -
Page 4: Symbols
Avoid unintentional power tool switching or startup. Avoid unintentional switching or startup. Packaging Packaging The product is placed in a package preventing damage during transport. This package is a raw The product is placed in a package preventing damage during transport. This package is a raw material therefire it can be handed over for recycling. -
Page 5: Operating Conditions
3. PRODUCT INTRODUCTION a. Submersible water pumps comply with standard DBP2500 the motor pump mainly consists of three parts: pump, mechanical seal and motor, pump is as the upper part of motor pump, which consists by stator and rotator. Motor is at the lower part of the motor pump and it is a single-phase or three-phase asynchronous motor. -
Page 6: Machine Description
6. MACHINE DESCRIPTION Start-up We recommend installing a check valve on the transport side to avoid water shock. Be careful not to damage the power cord when the pump is discharged into the well. Fasten the power cord to the water pipe every 3 meters. Place the pump in a tank or reservoir The tank or reservoir must be large enough, not to turn off the pump too often (see operating limits). - Page 7 Connecting For a single-phase version: see the diagram. Use the control panel with the condenser and the switch. Protection Each deep well pump has built-in, manually resettable overload protection and automatically rever- sible overheating protection. Check direction of rotation Check the correct direction of rotation. The right direction is the one that gives the maximum height with the same amount of water absorbed.
-
Page 8: Technical Specification
7. TECHNICAL SPECIFiCATIONS DBP1800 Power: 900W Max. ow: 1900 L/h Max. height: 110m Max. pressure: 11 bar Depth of immersion: 5-30m Pump case diameter: 76mm Connection connector diameter: 1" Cable section: 3x0.75mm Length of cable: 20m Acceptable liquid temperature: 40C Installation method: Submersible vertical N.W./G.W.: 9.8/10.3 kg... -
Page 9: Troubleshooting
9. TROUBLESHOOTING Problem Main reasons Solving ways 1. The voltage is too low. 1. Adjust voltage between 342~418. in starting 2. Powe supply was cut o or phase lost. 2. Find out the reasons and settle it. 3. Impeller was clogged. 3. -
Page 10: Recommended Pump Installation Diagram
RECOMMENDED PUMP INSTALLATION DIAGRAM 1. Pump 2. Clamps for fastening the supply cable 3. Level control sensors 4. Fastening the cable 5. Manometer 6. Check valve 8. Power cable 11. Pressure switch 9. RECOMMENDED PUMP INSTALLATION DIAGRAM Static level Dynamic level 1 meter 1 meter 1. - Page 11 ....12...
- Page 13 place for future reference. We recommend keeping the original package including the inner packa- ging materials, cash voucher and guarantee card for a period of warranty at minimum. Fir a case if transportation, pack the machine into the original box from the manufacturer, thus ensuring a maximum protection of the product during a possible transport (e.g.
- Page 14 2 m.
- Page 16 DBP1800 DBP2500 7. TECHNICAL SPECIFiCATIONS Power: 1200 W Speed: 2850 rpm Max. height: 135 m Max. pressure: 13.5 bar Depth of immersion: 5-30 m Pump case diameter: 100 mm Connection connector diameter: 1” ° ° Cable section: 3x0.75 mm Length of cable: 20 m Acceptable liquid temperature: 40 °C...
- Page 18 9. RECOMMENDED PUMP INSTALLATION DIAGRAM Static level Dynamic level 1 meter 1 meter 1. Pump 2. Clamps for fastening the supply cable 3. Level control sensors (protection against dry running)
-
Page 19: Exploded View And Spare Part List
9. EXPLODED VIEW AND SPARE PART LIST... - Page 20 DESCRIPTION...
-
Page 21: Declaration Of Conformity
CE DECLARATION OF CONFORMITY / ЕС ДЕКЛАРАЦИЯ ЗА СЪОТВЕТСТВИЕ (EN) SUBMERSIBLE WATER PUMP 1900 l/h, 900 W/ 2600 l/h, 1200 W MODELS: DBP1800/3QG(D)1.2-50-0.55, DBP2500/4QGD2-60-0.75 We GBR Corp. LTD, Room 1002, 10/F., David House, 8-20 Nanking Street, Jordan, Kowloon, Hong Kong, China, declare under our sole responsibility that this product is in conformity and accordance with the following stan- (BG) ПОМПА... - Page 22 14. ГАРАНЦИОННА КАРТА Купувач ( ):......................име и фамилия/наименование на фирма и ЕИК ....................................Адрес: ....................Тел: ..............Тип на машината: ..............................Модел: ..................................Сериен № на машината*: ............Арт. №: ............... Сериен № на батерията*: ............Арт. №: ............... Сериен № на зарядната станция*: ..........
- Page 23 Гаранционни условия Моторните, пневматичните и електроинструментите, предлагани от Дженерал Дистрибюшън АД /Дружеството/, са инструменти и машини, предназначени за домашна и хоби употреба, конструирани и произведени съгласно действащите нормативни директиви и стандарти за съответствие на Европейския съюз, като са изпълнени изискванията за безопасност. Търговската гаранция за машините и пневматичните...
- Page 24 повредата е причинена от претоварване или липса на вентилация и недостатъчно смазване на движещите се компоненти; блокирало бутало в цилиндъра /залепени сегменти/, износени лагери и семеринги на коляновия вал, следствие на недостатъчно смазване или работа с блокирана спирачка; запушена горивна система; натрупан...
Need help?
Do you have a question about the DBP1800 and is the answer not in the manual?
Questions and answers