Subscribe to Our Youtube Channel
Related Manuals for Daewoo GP25-2
Summary of Contents for Daewoo GP25-2
- Page 1 GP25-2 Gasoline water pump USER'S MANUAL www.daewoopowerproducts.com Manufactured under license of Daewoo International Corporation, Korea...
-
Page 2: Table Of Contents
INDEX 1. PARTS LOCATION ........................... 2 2. SPECIFICATIONS ............................ 3 3. WARNING LABELS ON THE MACHINE ....................3 4. FOR SAFE OPERATION .......................... 4 5. SET UP ..............................5 6. OPERATION ............................. 8 7. MAINTENANCE ............................10 8. STORAGE ............................... 13 9. -
Page 3: Parts Location
1. PARTS LOCATION 01. Carry Handle 02. Switch 03. Throttle Lever 04. Choke lever 05. Fuel Tank 06. Recoil starter 07. Drain cap 08. Discharge port 09. Suction port 10. Pump drain plug... -
Page 4: Specifications
2. SPECIFICATIONS Engine Engine type 1E40F-5 Rated power (kg) Starting System Normal start Fuel Tank Capacity (L) 1. 2 Oil type/oil capacity 2 stroke, mixing oil Speed （rpm） 7600 Pump Pump type 1 inch Suction diameter/Exit diameter （mm） ... -
Page 5: For Safe Operation
Wear hearing protection! Wear protective gloves. Wear safety footwear With this symbol the manufacturer confirms that this power tool is in accordance with applicable European directives. If warning label peel off or become soiled and impossible to read, you should contact the dealer from which you purchased the product to order new labels and affix them in the required location(s). - Page 6 16. Take it to your dealer who will dispose of it properly. Always call your dealer for any clarification or priority action. INTEND USE Only pump the water that is not intended for human consumption. Pumping flammable liquids, such as gasoline or fuel oils, can result in a fire or explosion, causing serious injury.
-
Page 7: Set Up
• Check the fuel level. Starting with a full tank will help to eliminate or reduce operating interruptions for refueling. 5. SET UP PUMP PLACEMENT For best pump performance, place the pump near the water level, and use hoses that are no longer than necessary. - Page 8 near the water level, and the hoses are short. Never use a suction hose with an inside diameter less than 25 mm (1 inch). Use a hose clamp to securely fasten the hose connector to the suction hose in order to prevent air leakage and loss of suction.
-
Page 9: Operation
FUEL WARNING • Gasoline is very flammable. Avoid smoking or bringing any flame or sparks near fuel. • Wipe up all spills before starting the engine. • Make sure to stop the engine and allow it cool before refueling the unit. •... - Page 10 NOTE Operating the pump dry will destroy the pump seal. If the pump has been operated dry, stop the engine immediately, and allow the pump to cool before priming. STARTING ENGINE 1. Rest the unit on a flat, firm place. Keep the cutting head off the ground and clear of surrounding objects as it will start rotating upon starting of the engine.
-
Page 11: Maintenance
SETTING ENGINE SPEED After starting the engine, move the throttle lever to the HIGH position for self-priming, and check pump output. Pump output is controlled by adjusting engine speed. Moving the throttle lever in the HIGH direction will increase pump output, and moving the throttle lever in the LOW direction will decrease pump output. - Page 12 Every 25 Every 50 Every hours hours after System/components Procedure Before use Note after hoursaft fuel leaks, fuel spillage wipe out fuel tank, air filter, fuel filter inspect/clean replace, if necessary see adjusting idling speed replace carburetor if idle speed adjuster necessary clean and readjust plug GAP: .025 in (0.6 ~ 0.7...
- Page 13 SPARK PLUG •Starting failure and mis-firing are often caused by a fouled spark plug. Periodically clean the spark plug and check that the spark gap is in the correct range. (MA3) When you take off the spark plug, twist (1) and pull off the cap (2). (MA4) Note that using any spark plugs other than those designated may result in the engine failing to operate properly or in the engine becoming overheated and damaged.
-
Page 14: Storage
PROCEDURES TO BE PERFORMED AFTER EVERY 10 HOURS OF USE 1. Remove the muffler, insert a screwdriver into the vent, and wipe away any carbon buildup. Wipe away any carbon buildup on the muffler exhaust vent at the same time. (MA7) 2. -
Page 15: Troubleshooting Guide
9. TROUBLESHOOTING GUIDE ----------------------------------------------------------------------------------------------------------------------------- Case 1. Starting failure ----------------------------------------------------------------------------------------------------------------------------- CHECK PROBABLE CAUSES ACTION ----------------------------------------------------------------------------------------------------------------------------- fuel tank incorrect fuel drain it and with correct fuel fuel filter fuel filter is clogged clean carburetor adjustment screw out of normal range adjust to normal range sparking (no spark) spark plug is fouled/wet clean/dry... - Page 16 Manufactured under license of Daewoo International Corporation, Korea...
Need help?
Do you have a question about the GP25-2 and is the answer not in the manual?
Questions and answers