Function And Control; Remote Controller Introduction Of Yap1F7F(Wifi) - Gree VIREO GEN3 3VIR09HP115V1A Service Manual

6. Function and Control

Service Manual

6.1 Remote Controller Introduction of YAP1F7F(WiFi)

Notice:
1.This is a general use remote controller. It could be used for the air conditioner with multifunction. For the functions which the
model doesn't have, if press the corresponding button on the remote controller, the unit will keep the original running status.
2.After putting through the power, the air conditioner will give out a sound. Operation indicator "
colour is different for different models). After that, you can operate the air condition-er by using remote controller.
3.Under on status, pressing the button on the remote controller, the signal icon "
blink once and the air condition-er will give out a " di " sound, which means the signal has been sent to the air conditioner.
4.As for the models with functions of WiFi or wired controller, the indoor unit must has been controlled by standard remote
controller under auto mode first, and then the function of adjustable temperature under auto mode can be realized by APP or
the wired controller.
5.This remote controller can adjust the temperature under auto mode. When matching with the unit which is without the
function of adjustable temperature under auto mode, the set temperature under auto mode may be invalid, or the displayed set
temperature on the unit is not same as that on the remote controller under auto mode.
button
Press this button to turn on the unit. Press this button again to
turn off the unit.
button
Press this button to select your required operation mode :
● When selecting auto mode, air conditioner will operate
automatically according to the sensed temperature. Set
temperature can be adjusted and will be displayed a s
w e l l . P r e s s " F A N " b u t t o n c a n a d j u s t f a n s p e e d .
Press " "/" " button can adjust fan blowing angle.
● After selecting cool mode, air conditioner will operate
under cool mode. Press "
temperature. Press "FAN" button to adjust fan speed.
P r e s s " " / " " b u t t o n t o a d j u s t f a n b l o w i n g a n g l e .
Technical Information
ON/OFF
MODE
I FEEL T-ON T-OFF
TEMP CLOCK
LIGHT WiFi SLEEP
" or " " button to adjust set
" on the display of remote controller will
● When selecting dry mode, the air conditioner operates at low
speed under dry mode. Under dry mode, fan speed can't be
adjusted. Press " "/" " button to adjust fan blowing angle.
● When selecting fan mode, the air conditioner will only blow
fan, no cooling and no heating. Press "FAN" button to adjust
fan speed. Press" "/" " button to adjust fan blowing angle.
When selecting heat mode, the air conditioner operates under
heat mode. Press "▲" or "▼" button to adjust set temperature.
Press "FAN" button to adjust fan speed. Press "
to adjust fan blowing angle.
● When selecting heating mode, the air conditioner operates
under heat mode. Press "
temperature. Press "FAN" button to adjust fan speed. Press "
/ " "button to adjust fan blowing angle. (Cooling only unit won't
receive heating mode signal. If setting heat mode with remote
controller, press ON/OFF button can't start up the unit).
Notice:
● For preventing cold air, after starting up heat mode,indoor unit
will delay 1~5 minutes to blow air (Actual delay time depends on
indoor ambient temperature).
● Set temperature range from remote controller: 16~30
o
86 F).
● Under auto mode, temperature can be displayed;Under auto
mode, set temperature can be adjusted.
● This mode indicator is not available for some models.
button
This button is used for setting Fan Speed in the sequence that
goes from AUTO, , ,
Auto.
*Note:
● Under AUTO speed, air conditioner will select proper fan speed
automatically according to factory default setting.
● It's low fan speed under dry mode.
● X-FAN function Hold fan speed button for 2s in cool or dry
mode, the icon " " is displayed and the indoor fan will continue
operation for a few minutes in order to dry the indoor unit even
though you have turned off the unit. After energization, X-FAN
OFF is defaulted. X-FAN is not available in auto, fan or heat mode.
● This function indicates that moisture on evaporator of indoor
unit will be blowed after the unit is stopped to avoid mould.
● Having set X-FAN function on: After turning off the unit
" is ON (red indicator, the
" / " " button
" or " "button to adjust set
, , , , then back to
"
o
C(61-
29