Table of Contents
Advertisement
POWER MIG
®
350MP
DRIVE ROLL KITS
Refer to Table C.1 for various drive roll kits that are
available for the POWER MIG
Bold are supplied standard with the POWER MIG
350MP.
TABLE C.1
Wire
Size
.023"-.030" (0.6-0.8 mm)
Solid
.035" (0.9 mm)
Steel
.045" (1.2 mm)
.035-.045" (0.9-0.2mm)
.040" (1.0mm)
.035" (0.9 mm)
Cored
.045" (1.2 mm)
Aluminum
3/64" (1.2 mm)
*
.035 Aluminum recommended for Push-Pull systems only.
K363P READI-REEL ADAPTER
The K363P Readi-Reel Adapter mounts to the 2"
spindle. It is needed to mount the 22-30 lb. Readi-
Reels.
DUAL CYLINDER MOUNTING KIT
(K1702-1)
Permits stable side-by-side mounting of two full size
(9" dia. x 5' high) gas cylinders with "no lift" loading.
Simple installation and easy instructions provided.
Includes upper and lower cylinder supports, wheel
axles and mounting hardware.
MAGNUM GMAW GUN AND CABLE
ASSEMBLIES
The following Magnum 350MP gun and cable assem-
blies are separately available for use with the POWER
MIG
350MP. Each is rated 350 amps 60% duty cycle
®
(or 350 amps 40% duty) and is equipped with the inte-
grated connector, twist-lock trigger connector, fixed
nozzle and insulator, and includes a liner, diffuser, and
contact tips for the wire sizes specified:
350MP. All items in
®
®
Drive Roll Kit
KP1696-030S
KP1696-035S
KP1696-045S
KP-1696-1
KP-1696-2
KP1697-035C
KP1697-045C
KP1695-3/64A
C-1
Part No.
Length
Wire Size
K470-1
10' (3.0 m)
.035 – .045"
◊
K470-2
15' (4.6 m)
.035 – .045"
K470-4
15' (4.6 m)
.052 – 1/16"
K470-6
15' (4.6 m)
1/16 – 5/64"
◊
This Part Number is the standard Gun and Cable Assembly sent
with the POWER MIG
®
350MP from the factory.
MAGNUM GUN CONNECTION KIT
(Optional K466-6)
Using the optional K466-6 Magnum Connection kit for
the POWER MIG
®
350MP permits use of standard
Magnum 200, 350 or 400 gun and cable assemblies.
CAUTION
Closing either gun trigger will cause the electrode of
both guns to be electrically "HOT". Be sure unused
gun is positioned so electrode or tip will not contact
metal case or other metal common to work.
---------------------------------------------------------------------------
Because the control circuitry senses each gun through its trig-
ger leads, weld parameters are displayed and adjustable for
the last gun that was triggered.
1. Pulling the trigger for the built-in feeder gun (Magnum
350):
•
Disables spool gun operation.
•
Changes the displays of the POWER MIG
correspond to feeder gun operation.
•
Closing feeder gun trigger starts feeder gun welding
and makes both electrodes electrically "HOT".
2. Pulling SPOOL GUN Trigger:
•
Disables built-in feeder gun operation.
•
Changes the displays of the POWER MIG
correspond to Spool Gun operation.
•
Closing spool gun trigger starts spool gun welding and
makes both electrodes electrically "HOT".
3. Operation with POWER MIG
•
Install the spool gun per the installation instructions
•
Turn the POWER MIG
•
Make sure that the Gun Selector Switch is in the
"Standard / Spool Gun" position.
•
Pull and release the trigger of the Spool Gun. The
POWER MIG
®
recognizes the spool gun as active and
weld parameters are adjustable for welding with the
Spool Gun
ACCESSORIES
Metric Wire Size
0.9 – 1.2 mm
0.9 – 1.2 mm
1.3 – 1.6 mm
1.6 – 2.0 mm
®
350MP to
®
350MP to
®
350MP:
®
350MP input power ON.
Advertisement
Table of Contents
Troubleshooting
