Advertisement

Quick Links

Copyright
Copyright © 2023 MITAC COMPUTING TECHNOLOGY CORPORATION. All rights
reserved. No part of this manual may be reproduced or translated without prior
written consent from MITAC COMPUTING TECHNOLOGY CORPORATION.
Trademark
All registered and unregistered trademarks and company names contained in this
manual are property of their respective owners including, but not limited to the
following.
®
TYAN
is a trademark of MITAC COMPUTING TECHNOLOGY CORPORATION.
®
Intel
is a trademark of Intel
AMI, AMI BIOS are trademarks of AMI Technologies.
Microsoft
®
, Windows
®
Nuvoton
is a trademark of Nuvoton Technology Corporation.
Notice
Information contained in this document is furnished by MITAC COMPUTING
TECHNOLOGY CORPORATION and has been reviewed for accuracy and reliability
prior to printing. MITAC assumes no liability whatsoever, and disclaims any express
or implied warranty, relating to sale and/or use of TYAN
or warranties relating to fitness for a particular purpose or merchantability. MITAC
retains the right to make changes to product descriptions and/or specifications at
any time, without notice. In no event will MITAC be held liable for any direct or
indirect, incidental or consequential damage, loss of use, loss of data or other
malady resulting from errors or inaccuracies of information contained in this
document.
S5565
Version 1.0a
®
Corporation.
®
are trademarks of Microsoft Corporation.
http://www.tyan.com
®
products including liability
1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the S5565 and is the answer not in the manual?

Questions and answers

Summary of Contents for TYAN S5565

  • Page 1 TECHNOLOGY CORPORATION and has been reviewed for accuracy and reliability prior to printing. MITAC assumes no liability whatsoever, and disclaims any express ® or implied warranty, relating to sale and/or use of TYAN products including liability or warranties relating to fitness for a particular purpose or merchantability. MITAC retains the right to make changes to product descriptions and/or specifications at any time, without notice.
  • Page 2 http://www.tyan.com...
  • Page 3: Table Of Contents

    4.1 Flash Utility ..................95   4.2 AMIBIOS Post Code (Aptio) ............96   Appendix I: How to recover UEFI BIOS ..........103   Appendix II: Fan and Temp Sensors ............ 107   Glossary ....................109   Technical Support .................. 115   http://www.tyan.com...
  • Page 4: Before You Begin

    2 x SATA Cable 1 x M.2 Board Latch 1 x Rear IO Shield 1 x S5565 Quick reference guide IMPORTANT NOTE: Sales sample may not come with the accessory listed above. Please contact your sales representative to help order accessory for your evaluation.
  • Page 5: Chapter 1: Instruction

    32 and 64-bit computing, high-bandwidth memory design, and lightning-fast PCI-E bus implementation. The S5565 not only empowers you in today’s demanding IT environment but also offers a smooth path for future application upgradeability. All of these rich feature sets provides the S5565 with the power and flexibility to meet demanding requirements for today’s IT environments.
  • Page 6 Class B Operating Temp. 0° C ~ 55° C (32° F~ 131° F) Operating Non-operating Temp. - 40° C ~ 70° C (-40° F ~ 158° F) Environment In/Non-operating Humidity 90%, non-condensing at 35° C RoHS RoHS 6/6 Compliant http://www.tyan.com...
  • Page 7: Software Specifications

    Motherboard (1) S5565 Motherboard Manual (1) Quick Installation Guide Package Contains I/O Shield (1) I/O Shield Cable SATA (2) SATA signal cables 1.3 Software Specifications ® For OS (operation system) support, please check with TYAN support for latest information. http://www.tyan.com...
  • Page 8 NOTE http://www.tyan.com...
  • Page 9: Chapter 2: Board Installation

    Caution! To avoid damaging the motherboard and associated components, use torque force within the range kgf/cm (4.35 ~ 6.09 lb/in) on each mounting screw for motherboard installation. Do not apply power to the board if it has been damaged. http://www.tyan.com...
  • Page 10: Board Image

    2.1 Board Image S5565 This picture is representative of the latest board revision available at the time of publishing. The board you receive may not look exactly like the above picture. http://www.tyan.com...
  • Page 11: Block Diagram

    2.2 Block Diagram S5565 Block Diagram http://www.tyan.com...
  • Page 12: Mainboard Mechanical Drawing

    2.3 Mainboard Mechanical Drawing http://www.tyan.com...
  • Page 13: Board Parts, Jumpers And Connectors

    The board you receive may not look exactly like the above diagram. But for the DIMM number please refer to the above placement for memory installation. For the latest board revision, please visit our web site at http://www.tyan.com. http://www.tyan.com...
  • Page 14 CMOS Clear (CMOS1) Buzzer Select (J7) LEDs Slots SATA & M.2 LED (HDD_LED1) PCIE#1 (PCIE1) M.2_1 LED (LED1) PCIE#2 (PCIE2) M.2_2 LED (LED2) PCIE#3 (PCIE3) Jumper Legend OPEN - Jumper OFF Without jumper cover CLOSED - Jumper ON With jumper cover http://www.tyan.com...
  • Page 15 GND/5VDC 5VDC SATA0/1/4/5: 7-pin SATA Connector Signal USB3_FPIO1: Front USB3.0 Header Signal Signal P0_RX_N P0_RX_P P1_RX_N P1_RX_P P0_TX_N P0_TX_P P1_TX_N P1_TX_P P0_N P0_P P1_N OC_N P1_P FPIO1: Front Panel Header Signal Signal HDD_LED_P GRN_BLNK_HRD HDD_LED_N YLW_BLNK_HRD FP_PWR_BTN_N FP_RST_BTN_N 5Vdc http://www.tyan.com...
  • Page 16 FAN_PWM DBG_HD1: TPM Module Header Signal Signal VCC3_AUX TPM_CLK KTPM_PRSNT TPM_RST TPM_PRIQ_N TPM_MOSI VCC3 TPM_MISO TPM_CS2 EMPTY   INTRUD: INTRUDER Header Signal INTRUDER# FPIO_AUD1: Front Audio Header Signal Signal FP_MIC_L MIC2-JD FRONT-IO- SENSE FP_MIC_L EMPTY F_ADDET_N FP_HPOUT_L FP_HPOUT_R LINE2-JD http://www.tyan.com...
  • Page 17 TYPEA_USB3: Vertical Type-A USB3.0 Connector Pin1 Pin2 Pin3 Pin4 Pin5 5VDC Pin6 Pin7 Pin8 Pin9 GND1 GND2 USB2_FPIO1: Front USB2.0 Header (black) Signal Signal 5VDC 5VDC J6: ESPI Port 80 Header Signal Signal P3V3_AUX ESPI_CS1_N ESPI_DBG_IO0 ESPI_DBG_IO1 ESPI_RESET_N ESPI_DBG_IO2 ESPI_DBG_IO3 CLK _ESPI ESPI_ALERT1_N http://www.tyan.com...
  • Page 18 Clear CMOS. 4. Put jumper cap back to Pin_1 and Pin_2 (Default setting). 5. Reconnect power connectors to the motherboard and power on system. Pins 1&2 closed: Normal (Default) Pins 2&3 closed: Clear CMOS http://www.tyan.com...
  • Page 19 M.2#1~2: M.2 Header (Slot) Signal Name Signal Name P3V3 P3V3 PERN3 PERP3 I/O/LED PETN3 P3V3 PETP3 P3V3 P3V3 PERN2 P3V3 PERP2 PETN2 PETP2 PERN1 PERP1 PETN1 PETP1 M2_SMB_CLK2 PERN0 M2_SMB_DAT2 PERP0 PETN0 PETP0 M2_PERST_N REFCLKN REFCLKP NC21 P3V3_AUX 3.3V 3.3V http://www.tyan.com...
  • Page 20 PRSNT1# SMCLK JTAG2 SMDAT JTAG3 JTAG4 JTAG5 JTAG1 P3V3_AUX WAKE# PERST# RSVD_1 REFCLK+ PETp0 REFCLK- PETn0 PERp0 PRSNT2# PERn0 PETp1 RSVD_4 PETn1 PERp1 PERn1 PETp2 PETn2 PERp2 PERn2 PETp3 PETn3 PERp3 RSVD_2 PERn3 PRSNT2#_2 RSVD_5 PETp4 RSVD_6 PETn4 PERp4 http://www.tyan.com...
  • Page 21 PETp7 PETn7 PERp7 PRSNT2#_3 PERn7 PETp8 RSVD_7 PETn8 PERp8 PERn8 PETp9 PETn9 PERp9 PERn9 PETp10 PETn10 PERp10 PERn10 PETp11 PETn11 PERp11 PERn11 PETp12 PETn12 PERp12 PERn12 PETp13 PETn13 PERp13 PERn13 PETp14 PETn14 PERp14 PERn14 PETp15 PETn15 PERp15 PRSNT2#_4 PERn15 http://www.tyan.com...
  • Page 22 Signal Name Signal Name PRSNT1# SMCLK JTAG2 SMDAT JTAG3 JTAG4 JTAG5 JTAG1 V3AUX WAKE# PERST# RSVD_1 REFCLK+ PETp0 REFCLK- PETn0 PERp0 PRSNT2# PERn0 PETp1 RSVD_4 PETn1 PERp1 PERn1 PETp2 PETn2 PERp2 PERn2 PETp3 PETn3 PERp3 RSVD_2 PERn3 PRSNT2#_2 RSVD_5 RSVD_6 http://www.tyan.com...
  • Page 23 PRSNT2#_3 http://www.tyan.com...
  • Page 24: Led Definitions

    VCC3 HDD_ACT_LED_N SATA & M.2 HDD_LED1 State Description HDD non-activity Blue HDD activity Signal VCC3 M2_1_LED_N LED1 M.2_1 LED State Description HDD non-activity Blue HDD activity Signal VCC3 M2_2_LED_N LED2 M.2_2 LED State Description HDD non-activity Blue HDD activity http://www.tyan.com...
  • Page 25: Installing The Processor And Heat Sink

    Specifications on page 5. Check our website at http://www.tyan.com for latest processor support. NOTE: MITAC TYAN is not liable for damage as a result of operating an unsupported configuration. Installing Processor (in Socket LGA1700) Follow the steps below to install the processors and heat sinks. NOTE: Please save and replace the CPU protection cap when returning for service.
  • Page 26 3. Align and seat the processor package on the socket. Make sure the gold arrow is located in the right direction. 4. Close the load plate. 5. Remove and save the ILM cover. 6. Close the ILM lever and latch. http://www.tyan.com...
  • Page 27 Removing Processor 1. Open the ILM lever and then the load plate using the finger tab. 2. Place the ILM cover and then carefully remove the processor package. 3. Close the load plate and latch the ILM lever. http://www.tyan.com...
  • Page 28 The following diagram illustrates how to install the heat sink. Apply the thermal grease. Place the heat sink on top of the CPU and push the 4 latches in a diagonal pattern to lock it in place. http://www.tyan.com...
  • Page 29 Secure the heat sink screws. Connect the fan cable to complete the installation. http://www.tyan.com...
  • Page 30: Thermal Interface Material

    CPU lid (applying too much will actually reduce the cooling). NOTE: Always check with the manufacturer of the heat sink & processor to ensure that the thermal interface material is compatible with the processor and meets the manufacturer’s warranty requirements. http://www.tyan.com...
  • Page 31: Tips On Installing Motherboard In Chassis

    Some chassis include plastic studs instead of metal. Although the plastic studs are usable, MITAC recommends using metal studs with screws that will fasten the motherboard more securely in place. Below is a chart detailing what the most common motherboard studs look like and how they should be installed. http://www.tyan.com...
  • Page 32 http://www.tyan.com...
  • Page 33: Installing The Memory

    2.9 Installing the Memory Before installing memory, ensure that the memory you have is compatible with the motherboard and processor. Check the TYAN Web site at http://www.tyan.com details of the type of memory recommended for your motherboard.  Support (1) DIMM slots per channel ...
  • Page 34 3. Populate the same DIMM type in each channel, specifically - Use the same DIMM size - Use the same # of ranks per DIMM 4. Dual-rank DIMMs are recommended over single-rank DIMMs. 5. Always install with P0_CHA_DIM0 slot first, following the alphabetical order. http://www.tyan.com...
  • Page 35 Memory Installation Procedure Follow these instructions to install memory modules into the S5565. 1. Unlock the clips. 2. Insert the memory module. 3. Lock the clips. http://www.tyan.com...
  • Page 36: Attaching Drive Cables

    2.10 Attaching Drive Cables Attaching Serial ATA Cables S5565 is equipped with four (4) Serial ATA (SATA) channel. Connections for the drives are very simple. There is no need to set Master/Slave jumpers on SATA drives. If you are in need of SATA/SAS cables or power adapters please contact your place of purchase.
  • Page 37: Installing Add-In Cards

    Doing so allows air to circulate within the chassis more easily, thus improving cooling for all installed devices. NOTE: You must always unplug the power connector from the motherboard before performing system hardware changes to avoid damaging the board or expansion device. http://www.tyan.com...
  • Page 38: Connecting External Devices

    2.5G RJ45 Connector (LAN1) Diagram Color State Condition LAN link is not established LAN link is Link established Green LAN activity Blinking occurring 10 M/100M b/s data rate Orange 1000 M data rate Speed 2500 Mb/s data Green rate http://www.tyan.com...
  • Page 39 1G RJ45 Connector (LAN2) Diagram Color State Condition LAN link is not established LAN link is Link established Green LAN activity Blinking occurring 10 Mb/s data rate 100 Mb/s data Green Speed rate 1000 Mb/s data Orange rate http://www.tyan.com...
  • Page 40: Installing The Power Supply

    2.13 Installing the Power Supply There are two (2) power connectors on your S5565 motherboard. The S5565 supports EPS 12V power supply. NOTE: You must unplug the power supply before plugging the power cables to motherboard connectors. PWR1: ATX 24-pin Main Power Connector...
  • Page 41: Chapter 3: Bios Setup

    The table below shows how to navigate in the setup program using the keyboard. Function Left/Right Arrow Keys Change from one menu to the next Up/Down Arrow Keys Move between selections Enter Open highlighted section PgUp/PgDn Keys Change pages Change options Exit http://www.tyan.com...
  • Page 42 The following pages provide the details of BIOS menu. Please be noticed that the BIOS menu are continually changing due to the BIOS updating. The BIOS menu provided are the most updated ones when this manual is written. Please visit TYAN’s website at http://www.tyan.com for the information of BIOS updating. http://www.tyan.com...
  • Page 43: Main Menu

    Set the Date. Use Tab to switch between Date elements. Default Ranges: Year: 1998-9999 Months: 1-12 Days: dependent on month. Range of Years may vary. System Time Set the Time. Use Tab to switch between Time elements. hh: 0-23 mm: 0-59 ss: 0-59 http://www.tyan.com...
  • Page 44: Advanced Menu

    This section facilitates configuring advanced BIOS options for your system. CPU Configuration CPU Configuration Parameters. PCH-FW Configuration Configure Management Engine Technology Parameters. Trusted Computing Trusted Computing Settings. ACPI Settings System ACPI Parameters. Watchdog Timer Configuration Watchdog Configuration. NCT6796D Super IO Configuration System Super IO Chip Parameters. http://www.tyan.com...
  • Page 45 PCI Subsystem Settings PCI, PCI-X and PCI Express Settings. USB Configuration USB Configuration Parameters. Network Stack Configuration Network Stack Settings. CSM Configuration CSM Configuration: Enable/Disable, Option ROM execution settings, etc. NVMe Configuration NVMe Device Options Settings. Onboard Device Onboard Device Configuration. http://www.tyan.com...
  • Page 46 E-cores are looked at together. When both are {0, 0}, P-code will enable all cores. All / 7 / 6 / 5 / 4 / 3 / 2 / 1 / 0 (Note: The number of cores depends on your CPU.) http://www.tyan.com...
  • Page 47 Maximum Package C State Limit Setting. CPU Default: Leaves to Factory default value. Auto: Initializes to deepest available Package C State Limit. C0/C1 / C2 / C3 / C6 / C7 / C7S / C8 / C9 / C10 / CPU Default / Auto http://www.tyan.com...
  • Page 48 MEBx Setup. Note: This option does not disable Manageability Features in FW. Disabled / Enabled ME Unconfig on RTC Clear When Disabled ME will not be unconfigured on RTC Clear. Disabled / Enabled Firmware Update Configuration Configure Management Engine Technology Parameters. PTT Configuration Configure PTT. http://www.tyan.com...
  • Page 49 3.3.2.1 Firmware Update Configuration ME FW Image Re-Flash Enable/Disable ME FW Image Re-Flash function. Disabled / Enabled http://www.tyan.com...
  • Page 50 TPM Device Selection Select TPM device: PTT or dTPM. PTT - Enables PTT in SkuMgr dTPM 1.2 – Disables PTT in SkuMgr Warning! PTT/dTPM will be disabled and all data saved on it will be lost. dTPM / PTT http://www.tyan.com...
  • Page 51 3.3.3 Trusted Computing Security Device Support Enables or Disables BIOS support for security device. O.S. will not show Security Device. TCG EFI protocol and INT1A interface will not be available. Disabled / Enabled http://www.tyan.com...
  • Page 52 Enable or Disable System ability to Hibernate (OS/S4 Sleep State). This option may not be effective with some operating system. Disabled / Enabled ACPI Sleep State Select the highest ACPI Sleep state the system will enter when the SUSPEND button is pressed. Suspend Disabled / S3 (Suspend to RAM) http://www.tyan.com...
  • Page 53 The duration of enabling Watchdog Timer. When Watchdog time-out occurs, System will reboot immediately. Disabled / POST / OS / Power ON Watchdog Timer Select 2/4/6/8/10 minutes for Watchdog time intervals. Available when Watchdog Mode is not set to [Disabled]. http://www.tyan.com...
  • Page 54 3.3.6 NCT6796D Super IO Configuration Serial Port 1 Configuration Set Parameters of Serial Port 1 (COM1). Serial Port 2 Configuration Set Parameters of Serial Port 2 (COM2). http://www.tyan.com...
  • Page 55 / IO=3F8h; IRQ=3, 4, 5, 6, 7, 9, 10, 11, 12; / IO=2F8h; IRQ=3, 4, 5, 6, 7, 9, 10, 11, 12; / IO=3E8h, IRQ=3, 4, 5, 6, 7, 9, 10, 11, 12; / IO=2E8h, IRQ=3, 4, 5, 6, 7, 9, 10, 11, 12; http://www.tyan.com...
  • Page 56 / IO=3E8h, IRQ=3, 4, 5, 6, 7, 9, 10, 11, 12; / IO=2E8h, IRQ=3, 4, 5, 6, 7, 9, 10, 11, 12; Device Mode Change the Serial Port mode. Standard Serial Port Mode / IrDA Active pulse 1.6uS / IrDA Active pulse 1/16 bit time / ASKIR Mode http://www.tyan.com...
  • Page 57 Auto Fan Control Automatic Fan Control. Disabled: Fan speed full on. Enabled: Automatic fan speed control by temperature. Disabled / Enabled PWM Minimal Duty Cycle (suppressed if Auto Fan Control is Disabled) PWM Minimal Duty Cycle. 30% / 45% / 60% http://www.tyan.com...
  • Page 58 3.3.7.1 Sensor Data Register Monitoring Read Only. http://www.tyan.com...
  • Page 59 (available when Wake system from S5 is set to [Fixed time]) Wake up hour Select 0-23. For example enter 3 for 3am and 15 for 3pm. Wake up minute Select 0-59 for Minute. Wake up second Select 0-59 for Second. http://www.tyan.com...
  • Page 60 Wake system from S5 (available when Wake system from S5 is set to [Dynamic time]) Wake up minute increase Select 1-5. http://www.tyan.com...
  • Page 61 Legacy Console redirection settings. Console Redirection EMS Console redirection enable or disable. Disabled / Enabled Console Redirection Settings The settings specify how the host computer (which the user is using) will exchange data. Both computers should have the same or compatible settings. http://www.tyan.com...
  • Page 62 1’s in the data bits is odd. Mark: parity bit is always 1. Space: parity bit is always 0. Mark and Space parity do not allow for error detection. None / Even / Odd / Mark / Space http://www.tyan.com...
  • Page 63 On this mode enabled only text will be sent. This is to capture Terminal data. Disabled / Enabled Resolution 100x31 Enable or disable extended terminal resolution. Disabled / Enabled Putty KeyPad Select FunctionKey and KeyPad on Putty. VT100 / LINUX / XTERMR6 / SCO / ESCN / VT400 http://www.tyan.com...
  • Page 64 When BootLoader is selected, then Legacy Console Redirection is disabled before booting to legacy OS, When Always Enable is selected, then Legacy Console Redirection is enabled for legacy OS. Default setting for this option is set to Always Enable. Always Enable / BootLoader http://www.tyan.com...
  • Page 65 VT100 / VT100Plus / VT-UTF8 / ANSI Bits per Second Select serial port transmission speed. The speed must be matched on the other side. Long or noisy lines may require lower speeds. 9600 / 19200 / 57600 / 115200 http://www.tyan.com...
  • Page 66 ‘start’ signal can be sent to restart the flow. Hardware flow control uses two wires to send start/stop signal. None / Hardware RTS/CTS / Software Xon/Xoff Data Bits / Parity / Stop Bits Read only. http://www.tyan.com...
  • Page 67 Onboard LAN1 OPROM (I219) Enable or disable onboard LAN1 OPROM. Disabled / Enabled Onboard LAN2 OPROM (I225) Enable or disable onboard LAN2 OPROM. Disabled / Enabled PCIE#1~PCIE#3 Empty Enable or Disable Option ROM execution for selected Slot. Enabled / Disabled http://www.tyan.com...
  • Page 68 If system has Resizable BAR capable PCIe Devices, this option Enables or Disables Resizable BAR Support. Enabled / Disabled BME DMA Mitigation Re-enable Bus Master Attribute disabled during Pci enumeration for PCI Bridges after SMM Locked. Enabled / Disabled http://www.tyan.com...
  • Page 69 Disabled / Enabled USB Mass Storage Driver Support Enable/Disable USB Mass Storage Driver Support. Disabled / Enabled USB transfer time-out The time-out value for Control, Bulk and Interrupt transfers. 1 sec / 5 sec / 10 sec / 20 sec http://www.tyan.com...
  • Page 70 Controller. ‘AUTO’ uses default value: for a Root port it is 100 ms, for a Hub port the delay is taken from Hub descriptor. Auto / Manual NOTE: Device power up delay in seconds is available when Device power-up delay is set to [Manual]. http://www.tyan.com...
  • Page 71 Enable/Disable Ipv4 PXE Boot Support. If disabled IPV4 PXE boot option will not be created. Disabled / Enabled Ipv6 PXE Support (Available when Network Stack Enabled) Enable/Disable Ipv6 PXE Boot Support. If disabled IPV6 PXE boot option will not be available. Disabled / Enabled http://www.tyan.com...
  • Page 72 Wait time in seconds to press ESC key to abort the PXE boot. Use either +/- or numeric keys to set the value. Media detect count (Available when Network Stack Enabled) Number of times the presence of media will be checked. Use either +/- or numeric keys to set the value. http://www.tyan.com...
  • Page 73 3.3.14 NVMe Configuration Here shows the Device Name you installed. A sample screenshot shows below.  http://www.tyan.com...
  • Page 74 Enable or disable onboard LAN1 (I219). Disabled / Enabled LAN2 (T225) Enable or disable onboard LAN2 (I225). Disabled / Enabled Chassis Intrusion Detection Enabled: When a chassis open event is detected, the BIOS will display the event. Disabled / Enabled http://www.tyan.com...
  • Page 75: Chipset Menu

    3.4 Chipset Menu North Bridge System Agent (SA) Parameters. South Bridge PCH Parameters. http://www.tyan.com...
  • Page 76 3.4.1 North Bridge Configuration Memory Configuration Memory Configuration Parameters. Graphics Configuration Graphics Configuration. VMD Setup Menu VMD Configuration settings. http://www.tyan.com...
  • Page 77 3.4.1.1 Memory Configuration Memory Test On Warm Boot Enable or Disable Base memory Test Run on Warm Boot. Enabled / Disabled Maximum Memory Frequency Maximum Memory Frequency Selection in Mhz. Auto / 2666 / 2933 / 3200 http://www.tyan.com...
  • Page 78 Select which of IGFX/PEG/PCI Graphics device should be Primary Display or select HG from Hybrid GFx. Auto / IGFX / PEG Slot / PCH PCIe Internal Graphics Keep IGFX enabled based on the setup option. Auto / Disabled / Enabled http://www.tyan.com...
  • Page 79 Enable/Disable to VMD controller. Disabled / Enabled Enable VMD Global Mapping Enable/Disable to VMD Global Mapping. Disabled / Enabled RAID0 Enable/Disable RAID0 support. Disabled / Enabled RAID1 Enable/Disable RAID1 support. Disabled / Enabled RAID5 Enable/Disable RAID5 support. Disabled / Enabled http://www.tyan.com...
  • Page 80 Enabled / Disabled RRT volumes can span internal and eSATA drives Enable/Disable RRT volumes can span internal and eSATA drives. Enabled / Disabled Intel® Optane (TM) Memory Enable/Disable System Acceleration with Intel® Optane (TM) Memory feature. Enabled / Disabled http://www.tyan.com...
  • Page 81 Enable or Disable the High Precision Event Timer. Disabled / Enabled Restore AC Power Loss Specify what state to go to when power is re-applied after a power failure (G3 state). Power On / Power Off / Last State http://www.tyan.com...
  • Page 82 Determines how SATA controller(s) operate. AHCI Hot Plug Designates this port as Hot Pluggable. Disabled / Enabled SATA Device Type Identify the SATA port is connected to Solid State Drive or Hard Disk Drive. Hard Disk Drive / Solid State Drive http://www.tyan.com...
  • Page 83 3.4.2.2 HD Audio Configuration HD Audio Control Detection of the HD-Audio device. Disabled = HDA will be unconditionally disabled. Enabled = HDA will be unconditionally enabled. Disabled / Enabled Audio DSP Enable/Disable Audio DSP. Disabled / Enabled http://www.tyan.com...
  • Page 84: Security

    3.4 Security Administrator Password Set Administrator Password. User Password Set User Password. HDD Security Configuration HDD Security Configuration for selected drive. Secure Boot Secure Boot Configuration. http://www.tyan.com...
  • Page 85 Restore Factory Keys Force System to User Mode. Install factory default Secure Boot key databases. Reset to Setup Mode Delete all Secure Boot key databases from NVRAM. Key Management Enables expert users to modify Secure Boot Policy variables without full authentication. http://www.tyan.com...
  • Page 86 Platform Key (PK) Enroll Factory Defaults or load certificates from a file: 1. Public Key Certificate: a) EFI_SIGNATURE_LIST b) EFI_CERT_X509 (DER) c) EFI_CERT_RSA2048 (bin) d) EFI_CERT_SHAXXX 2. Authenticated UEFI Variable 3. EFI PE/COFF Image (SHA256) Key source: Factory, External, Mixed http://www.tyan.com...
  • Page 87 Authorized TimeStamps Enroll Factory Defaults or load certificates from a file: 1. Public Key Certificate: a) EFI_SIGNATURE_LIST b) EFI_CERT_X509 (DER) c) EFI_CERT_RSA2048 (bin) d) EFI_CERT_SHAXXX 2. Authenticated UEFI Variable 3. EFI PE/COFF Image (SHA256) Key source: Factory, External, Mixed http://www.tyan.com...
  • Page 88 Copy NVRAM content of Secure Boot variables to files in a root folder on a file system device. Enroll Efi Image Allow the image to run in Secure Boot mode. Enroll SHA256 Hash certificate of a PE image into Authorized Signature Database (db). http://www.tyan.com...
  • Page 89: Boot

    Bootup NumLock State Select the keyboard NumLock state. On / Off Quiet Boot Enable or disable Quiet Boot option. Disabled / Enabled Wait for ‘ESC’ If Error Wait for ‘ESC’ key to be pressed if error occurs. Disabled / Enabled http://www.tyan.com...
  • Page 90 Endless Boot Enabled: BIOS try bootable devices constantly in loop until finding a bootable device (Excluding Built-in EFI Shell). Disabled / Enabled Boot Option #1 ~ Boot Option #2 Sets the system boot order. Device Name / Disabled http://www.tyan.com...
  • Page 91: Save & Exit

    3.6 Save & Exit Save Changes and Exit Exit system setup after saving the changes. Discard Changes and Exit Reset system setup without saving any changes. Restore Defaults Restore/Load Default values for all the setup options. http://www.tyan.com...
  • Page 92: Mailbox

    1. Enter [admin] at your first MEBX login. Re-configure a new password. Intel® AMT Configuration  Network setup/Intel (R) ME Network Name Settings  Select FQDN and press the Enter key to bring up a dialog box. Enter [mitacad.com] as shown. http://www.tyan.com...
  • Page 93 Network Access State  Select [Network Active] http://www.tyan.com...
  • Page 94 NOTE http://www.tyan.com...
  • Page 95: Chapter 4: Diagnostics

    BIOS flash failure, you must contact your dealer for a replacement BIOS. There are no exceptions. TYAN does not have a policy for replacing BIOS chips directly with end users. In no event will TYAN be held responsible for damages done by the end user.
  • Page 96: Amibios Post Code (Aptio)

    South Bridge initialization before microcode loading 0x05 OEM initialization before microcode loading 0x06 Microcode loading 0x07 AP initialization after microcode loading 0x08 North Bridge initialization after microcode loading 0x09 South Bridge initialization after microcode loading 0x0A OEM initialization after microcode loading 0x0B Cache initialization http://www.tyan.com...
  • Page 97 CPU post-memory initialization is started 0x33 CPU post-memory initialization. Cache initialization 0x34 CPU post-memory initialization. Application Processor(s) (AP) initialization 0x35 CPU post-memory initialization. Boot Strap Processor (BSP) selection 0x36 CPU post-memory initialization. System Management Mode(SMM) initialization 0x37 Post-Memory North Bridge initialization is started http://www.tyan.com...
  • Page 98 Reserved for future AMI progress codes S3 Resume Error Codes 0xE8 S3 Resume Failed 0xE9 S3 Resume PPI not Found 0xEA S3 Resume Boot Script Error 0xEB S3 OS Wake Error 0xEC – 0xEF Reserved for future AMI error codes http://www.tyan.com...
  • Page 99 CPU DXE initialization (CPU module specific) 0x67 CPU DXE initialization (CPU module specific) 0x68 PCI host bridge initialization 0x69 North Bridge DXE initialization is started 0x6A North Bridge DXE SMM initialization is started 0x6B North Bridge DXE initialization (North Bridge module specific) http://www.tyan.com...
  • Page 100 USB initialization is started 0x9B USB Reset 0x9C USB Detect 0x9D USB Enable 0x9E -0x9F Reserved for future AMI codes 0xA0 IDE initialization is started 0xA1 IDE Reset 0xA2 IDE Detect 0xA3 IDE Enable 0xA4 SCSI initialization is started http://www.tyan.com...
  • Page 101 No Console Output Devices are found 0xD7 No Console Input Devices are found 0xD8 Invalid password 0xD9 Error loading Boot Option (LoadImage returned error) 0xDA Boot Option is failed (StartImage returned error) 0xDB Flash update is failed 0xDC Reset protocol is not available http://www.tyan.com...
  • Page 102 System is waking up from the S3 sleep state 0x40 System is waking up from the S4 sleep state 0xAC System has transitioned into ACPI mode. Interrupt controller is in PIC mode. 0xAA System has transitioned into ACPI mode. Interrupt controller is in APIC mode. http://www.tyan.com...
  • Page 103: Appendix I: How To Recover Uefi Bios

    Except hotkey, the recovery also can be invoked automatically if Boot Block code finds that Main Block is corrupted. The supported storage devices are:  SATA HDD  USB Flash Drive The supported file system are:  FAT: FAT12, FAT16, FAT32  NTFS http://www.tyan.com...
  • Page 104 If recovery is triggered, system will enter recovery screen as shown below. Move the cursor to the Proceed with flash update submenu, press Enter to continue. http://www.tyan.com...
  • Page 105 It takes a few minutes to update the main firmware. A sample screenshot is shown below. http://www.tyan.com...
  • Page 106 If no recovery file is found, a “ROM Image is not loaded. ROM Image update denied.” message will display on the screen. http://www.tyan.com...
  • Page 107: Appendix Ii: Fan And Temp Sensors

    The red mark indicates the sensor. Fan and Temp Sensor Location: Fan Sensor: It is located in the third pin of the fan connector, which detects the fan speed (rpm). Temp Sensor: refer to Figure 1: Sensor Location. They detect the system temperature around. http://www.tyan.com...
  • Page 108 Temperature of P0_CHA_DIM0 Slot P0_CHA_DIM1 Temperature of P0_CHA_DIM1 Slot P0_CHB_DIM0 Temperature of P0_CHB_DIM0 Slot P0_CHB_DIM1 Temperature of P0_CHB_DIM1 Slot CPU0_FAN Fan Speed of CPU0_FAN SYS_FAN_1 Fan Speed of System_FAN1 SYS_FAN_2 Fan Speed of System_FAN2 SYS_FAN_3 Fan Speed of System_FAN3 http://www.tyan.com...
  • Page 109: Glossary

    (reading to or writing from a disk drive a single time is much faster than doing so repeatedly) there is the possibility of losing your data should the system crash. Information in a buffer is temporarily stored, not permanently saved. http://www.tyan.com...
  • Page 110 (like soundcards or keyboards) to access the main memory without involving the CPU. This frees up CPU resources for other tasks. As with IRQs, it is vital that you do not double up devices on a single line. Plug-n-Play devices will take care of this for you. http://www.tyan.com...
  • Page 111 EEPROM (Electrically Erasable Programmable ROM): also called Flash BIOS, it is a ROM chip which can, unlike normal ROM, be updated. This allows you to keep ® up with changes in the BIOS programs without having to buy a new chip. TYAN ’s BIOS updates can be found at http://www.tyan.com...
  • Page 112 PXE (Preboot Execution Environment): one of four components that together make up the Wired for Management 2.0 baseline specification. PXE was designed to define a standard set of preboot protocol services within a client with the goal of allowing networked-based booting to boot using industry standard protocols. http://www.tyan.com...
  • Page 113 NVIDIA s (graphics communications processing units) and NVIDIA MCPs (media and processors). application Depending on the , NVIDIA SLI can deliver as much as two times the performance of a single GPU configuration. http://www.tyan.com...
  • Page 114 CPUs without damaging the sensitive CPU pins. The CPU is lightly placed in an open ZIF socket, and a lever is pulled down. This shifts the processor over and down, guiding it into the board and locking it into place. http://www.tyan.com...
  • Page 115: Technical Support

    (which can have expensive consequences). If these options are not available for you then TYAN can help. Besides designing innovative and quality products for over a decade, TYAN has continuously offered customers service beyond their expectations.
  • Page 116 (RMA) number. The RMA number Should be prominently displayed on the outside of the shipping carton and the package should be mailed prepaid. TYAN will pay to have the board shipped back to you. This device complies with part 15 of the FCC Rules.

Table of Contents