Table of Contents
Advertisement
Programmable head-end amplifier
Deleting of settings
This menu allows you to delete settings that are saved in the Universal
programmer. The keyboard correspondence in this menu is as follows:
/
This enables the selecting of values for each option.
(short press) - Enables the modifying option.
(long press) - Nothing.
(short press) - Nothing.
(long press) - Runs the action indicated in "Command" option
Procedure
Simultaneously press keys
and
menu will show for a few seconds and then the save menu will appear.
------------
Save
Mode
------------
------------
Press the
key to activate the "Settings Index". Using the
Save
<01> MODE
Mode
setting you wish to delete from those displayed. This index allows you to browse
- Avant HD -
------------
------------
Stgo DC - #2
through them and select the setting you wish to delete. With each setting a
Save
(exit)
Mode
non modifiable line of text appears indicating what device each loaded setting
------------
corresponds to.
<01> MODE
------------
- Avant HD -
Save
The "Setting description" allows us to identify a certain setting when there are a
<07>
MODE
Stgo DC - #2
Mode
- Avant HD -
(exit)
number of different ones saved for the same device.
<01> MODE
------------
------------
Domaio - #3
- Avant HD -
Save
(exit)
Stgo DC - #2
Mode
(exit)
------------
<01> MODE
<07>
MODE
- Avant HD -
- Avant HD -
<07> MODE
Stgo DC - #2
Domaio - #3
- Avant HD -
<01> MODE
(exit)
(exit)
<07>
MODE
Domaio - #3
- Avant HD -
- Avant HD -
(exit)
Stgo DC - #2
Domaio - #3
(exit)
(exit)
The next press of the
key takes us to the "Command" option. Using the
<07> MODE
<07>
MODE
keys select the Delete option (it deletes the setting indicated by the setting
- Avant HD -
- Avant HD -
<07> MODE
Domaio - #3
index).
Domaio - #3
- Avant HD -
(exit)
<07> MODE
<07>
(exit)
MODE
Domaio - #3
Finally delete the selected setting by pressing the
- Avant HD -
- Avant HD -
(delete)
Domaio - #3
Domaio - #3
seconds.
(exit)
(exit)
<07> MODE
<07> MODE
- Avant HD -
- Avant HD -
------------
Domaio - #3
Domaio - #3
Deleting
(delete)
<07> MODE
(exit)
<07> MODE
config
- Avant HD -
- Avant HD -
------------
Domaio - #3
Domaio - #3
(exit)
(delete)
------------
<07> MODE
Deleting
- Avant HD -
<7> MODE
config
Domaio - #3
-
-
------------
<07> MODE
(delete)
------------
............
Deleting
- Avant HD -
(exit)
Domaio - #3
config
(delete)
------------
------------
<7> MODE
Deleting
-
config
............
Note: - The language in which the messages and menu are
(exit)
------------
------------
<7> MODE
Deleting
displayed will be the same as that of the connected
-
config
............
device. If the latter does not accept languages, they will
------------
(exit)
appear by default in English.
<7> MODE
-
-
............
(exit)
<7> MODE
-
-
............
(exit)
to enable the cloning option. The startup
------------
Save
Mode
------------
/
keys, select the
<01> MODE
- Avant HD -
Stgo DC - #2
(exit)
<07>
MODE
- Avant HD -
Domaio - #3
(exit)
<07> MODE
- Avant HD -
Domaio - #3
(exit)
<07> MODE
key for more than three
- Avant HD -
Domaio - #3
(delete)
------------
Deleting
config
------------
<7> MODE
-
-
............
(exit)
-
-
Error message
During the cloning process some of the following error messages can appear:
------------
The unit you are trying to copy/load does not allow
------------
NOT
------------
------------
settings cloning.
NOT
AVAILABLE
NOT
NOT
------------
------------
------------
AVAILABLE
------------
AVAILABLE
AVAILABLE
NOT
NOT
NOT
------------
------------
------------
AVAILABLE
AVAILABLE
AVAILABLE
------------
------------
------------
------------
------------
COPY
------------
There was a problem during the copy process. The setting
------------
FAILED
COPY
COPY
COPY
------------
------------
------------
could not be copied successfully to control.
------------
FAILED
FAILED
FAILED
COPY
COPY
COPY
------------
------------
------------
FAILED
FAILED
FAILED
------------
------------
------------
------------
------------
There was some problem during the loading process. The
------------
LOAD
------------
LOAD
FAILED
LOAD
LOAD
------------
------------
setting could not be successfully loaded to the device.
------------
FAILED
------------
FAILED
FAILED
LOAD
LOAD
LOAD
------------
------------
------------
FAILED
FAILED
FAILED
------------
------------
------------
------------
The setting you are trying to load does not correspond to
------------
------------
REFERENCE
------------
REFERENCE
REFERENCE
NOT VALID
REFERENCE
------------
------------
the device connected to control. The loading operation
------------
NOT VALID
------------
NOT VALID
NOT VALID
REFERENCE
REFERENCE
REFERENCE
------------
------------
has been aborted.
------------
NOT VALID
NOT VALID
NOT VALID
------------
------------
------------
------------
------------
INVALID
------------
------------
The setting you are trying to load on the unit is not
FIRMW VERS
INVALID
INVALID
INVALID
------------
------------
------------
FIRMW VERS
------------
FIRMW VERS
compatible because the firmware version of the loaded
FIRMW VERS
INVALID
INVALID
INVALID
------------
------------
------------
FIRMW VERS
FIRMW VERS
FIRMW VERS
setting does not correspond to the device connected to
------------
------------
------------
control. The loading operation could not take place.
------------
------------
------------
LANGUAGE
------------
LANGUAGE
READ ERROR
LANGUAGE
LANGUAGE
------------
------------
------------
READ ERROR
------------
READ ERROR
The working language of the unit can not be recovered.
READ ERROR
LANGUAGE
LANGUAGE
LANGUAGE
------------
------------
------------
READ ERROR
READ ERROR
READ ERROR
The copy/load operation has been aborted.
------------
------------
------------
------------
------------
------------
UNIT NAME
------------
UNIT NAME
UNIT NAME
READ ERROR
UNIT NAME
------------
------------
------------
READ ERROR
------------
READ ERROR
The name of the unit can not be recovered. The copy
READ ERROR
UNIT NAME
UNIT NAME
UNIT NAME
------------
------------
------------
READ ERROR
READ ERROR
READ ERROR
operation has not been completed successfully.
------------
------------
------------
/
Using "Reset" button
The "Avant" unit can be programmed before the installation is carried out
and without an input signal, and the levels can be adjusted later without the
use of the programmer, by using the "reset" button located to the left of the
programmer's connector.
To do so, please follow these steps:
Select the adequate parameters for the installation using the programmer
(channels, output level, equalisation slope ...) and press the
button (long press). As the programming is carried out without the input
signal, the adjustment will stop when it does not detect a UHF signal. The
programmer can then be unplugged, as although the adjustment process has
been interrupted, the data selected has been memorised by the unit.
Afterwards, once completed the installation by connecting the inputs to
be used and loading the output with 75 ohms, the user simply has to press
the "Reset" button and the unit will carry out the adjustment process. The
adjustment of the "Avant" unit via the "Reset" button is carried out in the
same way as with the programmer, although in this case, the process will not
stop if the units detect an error in the input levels and the red error LED will
only light up when there is an error in the level of any of the filters.
Therefore, if the unit has been programmed with the desired parameters for
the installation (channels, output level, equalisation slope ...), when the reset
button is pressed, the "Avant" unit will carry out an automatic adjustment of
the levels in the same way as when the programmer's adjustment button
is pressed and hold. The green LED will light up indicating that are being
adjusted all channel (that the unit already have in memory) levels for UHF,
FM, VHF and IF
amplifiers, while maintaing the input configurations, the
(1)
equalisation slope and the output levels that it had already configured.
(1) Not available in ref. 532910
14
adjustment
Advertisement
Table of Contents
