Table of Contents
Advertisement
Default configuration menu
The next menu is Default Configuration:
/
Modifies the parameter (YES/NO).
(short press) - Activates the cursor.
(long press) - Executes the selected option and returns to the main
menu.
(short press) - Changes to the PIN menu ignoring the changes.
(long press) - Saving
CONFIGURATION).
Load
default
Procedure
settings?
NO
Use
/
to select YES/NO, and confirm the action with the
load the default configuration and returns to the main menu.
Load
Load
default
default
settings?
settings?
NO
NO
Load
Load
default
default
settings?
settings?
Unit locking PIN menu
YES
NO
The following menu is Unit locking PIN:
Allows to increase or decrease each of the four digits of the password,
/
Load
the first between 0 ..7 and the rest between 0 .. 9 (0000 .. 7999).
default
settings?
(short press) - Places the cursor on the digits to be modified.
YES
(long press) - Enters the main menu and activates the locking.
(short press) - Changes to Filter Status menu.
(long press) - Saving and adjustment.
Procedure
The unit leaves the factory unlocked, to lock it you need to enter a four digit PIN
using this menu.
Press the
button to activate the first digit that composes the PIN. Use
PASSWORD
buttons to select a number between 0 and 7. Press again the
second digit and repeat the previous process to select a number between 0 and
0 0 0 0
9. Repeat until you complete the code.
PASSWORD
PASSWORD
0 0 0 0
0
0 0 0
PASSWORD
Once this code has been entered you must confirm it with a long press on the
PASSWORD
button. From now on, you can see all the menus but you cannot change the
0
0 0 0
6
0 0 0
configuration of the unit and you cannot save / adjust it (not even with the
external reset button).
While it is locked, all the menus of the programming unit show
this state. To unlock the unit, you need to enter the PIN again in this menu
PASSWORD
PASSWORD
following the same procedure (enter code and then confirm with a long press
6
0 0 0
6
0
0 0
of the
button) and the unit will be unlocked.
PASSWORD
6
0
0 0
CONFIG FI
Aten:
7dB
EQ:
3dB
LNB: 13V/ON
Load
default
settings?
NO
and
adjustment
(ignoring
DEFAULT
Load
default
settings?
NO
button. This will
Load
default
settings?
YES
PASSWORD
0 0 0 0
PASSWORD
PASSWORD
0
0 0 0
0 0 0 0
PASSWORD
PASSWORD
to activate the
6
0 0 0
0
0 0 0
PASSWORD
PASSWORD
6
0
0 0
6
0 0 0
-
í
PASSWORD
6
0
0 0
CONFIG FI
Aten:
EQ:
LNB: 13V/ON
indicating
CONFIG FI
Aten:
7dB
EQ:
3dB
LNB: 13V/ON
PASSWORD
6
0 0 0
PASSWORD
6
0
0 0
Example:
STATUS INFO
Unit is
CONFIG FI
not adjusted
Aten:
7dB
IF configuration menu in a password locked unit
EQ:
3dB
LNB: 13V/ON
STATUS INFO
(the status menu also informs of this locking)
The unit
has password
Saving and Adjustment process
Press
for more than three seconds from any of the menus/submenus and
the saving and adjustment process will begin. The display will indicate the
following information:
- Saving the configuration in EEPROM.
- Starting the adjustment.
- Configuration of the inputs.
- Previous scan (switch on of the powerings and automatic adjustment of the
input attenuators).
- UHF adjustment.
- Adjustment of each filter (with interaction of the user in the case of error).
Filter: 1
- VHF adjustment (in the case it is not cut-off ).
Input signal
Filter: 1
LOW LEVEL
- FM adjustment (in the case it is not cut-off ).
Input signal
LOW LEVEL
- Output attenuator adjustment.
- Adjustment of the highest channel programmed to a specific output level.
Programming
and saving
Programming
parameters
The errors regarding a high or low level are indicated by messages on the
and saving
...
parameters
display.
...
The adjustment can be attempted again by pressing the
Filter: 1
Input signal
ignored by pressing the
LOW LEVEL
Input power
and input
Filter: 1
Input power
attenuator
Input signal
and input
adjust ...
LOW LEVEL
attenuator
adjust ...
Examples:
Programming
and saving
parameters
...
UHF filters
automatic
Beginning of the saving and adjusting sequence.
Programming
UHF filters
adjustment
and saving
automatic
...
Long press of the
parameters
adjustment
...
...
Input power
and input
/
attenuator
Adjusting
adjust ...
filter: 1
Adjusting
Input power
...
Adjusting UHF filters.
filter: 1
and input
...
attenuator
Adjusting filter 1.
adjust ...
UHF filters
automatic
adjustment
Skipping
...
filter: 1
UHF filters
Skipping
...
automatic
filter: 1
adjustment
...
Filter: 1
Adjusting UHF filters.
...
Input signal
Low level input signal.
LOW LEVEL
Adjusting
filter: 1
Output level
...
automatic
Output level
adjustment
Adjusting
automatic
...
filter: 1
adjustment
7dB
Programming
...
...
and saving
3dB
Adjusting UHF filters.
Skipping
parameters
...
filter: 1
Ignoring adjustment of filter 1 by short pressing on the
Adjusting
...
filter Vout
button.
Adjusting
...
Skipping
filter Vout
filter: 1
...
...
Input power
Output level
and input
automatic
attenuator
adjustment
F1 F2 F3-
adjust ...
F4í F5í F6-
...
Final result of the adjustment.
F1 F2 F3-
F7í F8í F9í
Output level
F4í F5í F6-
F0í VHFí FMí
automatic
F7í F8í F9í
adjustment
F0í VHFí FMí
...
UHF filters
Adjusting
automatic
filter Vout
adjustment
...
...
Adjusting
filter Vout
...
button quickly.
button
11
EN
button quickly or
Advertisement
Table of Contents
