Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Minka Group minkaAire ALUMA
Summary of Contents for Minka Group minkaAire ALUMA
- Page 1 ALUMA INSTRUCTION MANUAL WARRANTY CERTIFICATE...
- Page 2 ©2019 Minka Lighting Inc. Manual design and all elements of manual design are protected by United States Federal and/or State Law including Patents, Trademark, and/or Copyright Laws.
- Page 3 The Minka-Aire® warranty is for one (1) year from the date of purchase from an authorized Minka-Aire® dealer. This warranty is only valid to the original purchaser or user against all defects in material and workmanship (light bulbs excluded) for one (1) full year. Additionally, Minka-Aire® warrants the motor only for the lifetime of the Minka Aire ceiling fan (excluding wall controls and electrical components), to the original purchaser or user.
- Page 4 Warranty Service Information To obtain warranty service during the warranty period, the purchaser should return the fan with the sales receipt to the original place of purchase. The authorized Minka-Aire® dealer, at its sole discretion, will either repair or replace the fan after verifying the legitimacy of the warranty claim.
-
Page 5: Table Of Contents
CONTENTS SAFETY RULES..................INSTALLING THE MOUNTING PLATE..........PACKAGE CONTENTS..............INSTALLING THE LED LIGHT KIT ............INSTALLING THE FAN..............INSTALLING THE GLASS SHADE ............. BLADE INSTALLATION ..............OPERATING YOUR FAN ..............HANGING THE FAN................. CARE OF YOUR FAN ................ELECTRICAL CONNECTIONS............TROUBLESHOOTING ................ -
Page 6: Safety Rules
SAFETY RULES 1. Before you begin installing the fan, shut power off at the circuit breaker of the fuse box. 2. Be cautious! Read all instructions and safety information before installing your new fan. Review accompanying assembly diagrams. 3. Make sure that all electrical connections comply with local codes, ordinances, or National Electrical Codes. Hire a qualified electrician or consult a do-it-yourself wiring handbook if you are unfamiliar with installing electrical wiring. - Page 7 NOTE: NOTE: The important safeguards and instructions appearing in this manual are not meant to cover all possible conditions and situations that may occur. It must be understood that common sense, caution and care are factors which can not be built into this product. These factors must be supplied by the person (s) installing, caring for and operating the unit.
-
Page 8: Package Contents
PACKAGE CONTENTS Unpack your fan and check the contents. You should have the following items: 1. Fan blades (4) A. Mounting hardware: 2. Hanger bracket #10 x 1.5 Wood screws (2 PCs.) 3. Canopy #8 x 3/4" Machine screws (2PCs.) 4. -
Page 9: Installing The Fan
INSTALLING THE FAN Tools Required: Phillips screw driver; slotted screw driver; step-ladder; wire cutters; electrical tape. PARALLEL WOOD BRACE CEILING MOUNTING OPTIONS (MIN. 2" THICK) JOIST OUTLET CROSS BRACE If there isn't an existing mounting box, then read the following instructions. Disconnect the power by removing fuses or turning off circuit breakers. -
Page 10: Blade Installation
BLADE INSTALLATION Step 1. (Fig. 5) Remove the upper cover by remove the 4 screws from the motor. SCREWS SCREWS Step 2. (Fig. 6) Insert the blade through the UPPER UPPER access window from the blade holder. Align COVER COVER holes from the blade and motor and secure with SCREWS 3 screws and fiber washers. -
Page 11: Hanging The Fan
HANGING THE FAN Step 4. Carefully feed fan wires up through the downrod. (Fig. 11) WARNING: WARNING: All of the parts, hardware and components such as the hanger bracket and hanger ball have been provided for your safety and the Thread Downrod into the Coupling until the holes are lined up and proper installation of your new ceiling fan. - Page 12 DOWNROD OUTLET BOX THREADED DOWNROD CROSS PIN SCREWS CANOPY HANGER SUPPLY CANOPY COVER REGISTRATION BALL SET SCREW WIRES SLOT SET SCREWS THREADED PIN DOWNROD HANGER BRACKET Fig. 13 Fig. 8 Fig. 9 Fig. 10 Fig. 11 Fig. 12...
-
Page 13: Electrical Connections
ELECTRICAL CONNECTIONS Follow the steps below to connect the fan to your house supply wires. Use the wire nuts supplied with your fan. Secure the wire nuts by wrapping the connection with electrical tape. Step 1. Disconnect the power and remove the existing wall plate and switch from the wall junction box. (Fig. 14) Step 2. - Page 14 SUPPLY CIRCUIT OUTLET BOX SWITCH WALL PLATE BLACK/ GROUND CONDUCTOR WHITE SCREWS SCREWS OUTLET BOX BLUE GREEN GROUND LEAD BLACK GROUND TO DOWNROD Fig. 14 Fig. 15...
-
Page 15: Installing The Wall Control
INSTALLING THE WALL CONTROL SWITCH OUTLET BOX SCREWS Remember to shut the power off at the circuit breaker or fuse box. WALL PLATE SCREWS WARNING: WARNING: HOOK UP IN "SERIES ONLY" DO NOT CONNECT THE HOT AND NEUTRAL WIRES OF ELECTRIC CIRCUIT TO THE WALL CONTROL - DAMAGE TO THE SWITCH AND POSSIBLE FIRE COULD OCCUR. -
Page 16: Finishing The Installation
FINISHING THE INSTALLATION OUTLET BOX Step 1. Remove 1 of the 2 screws from the bottom of the hanger bracket and loosen the other one half a turn from the screw head. HANGER BRACKET Step 2. Slide the canopy up towards the hanger bracket and place the key hole on the canopy over the screw on the hanger bracket, turn canopy until it locks in place at the narrow section of the key holes. -
Page 17: Installing The Mounting Plate
INSTALLING THE MOUNTING PLATE Step 1. Remove 1 of 3 screws from the mounting ring and loosen the other 2 screws. (Do not remove) Step 2. Place the key holes from the mounting plate over the 2 screws previously loosened from the mounting ring, turn mounting plate until it locks in place at the narrow section of the key holes. -
Page 18: Installing The Led Light Kit
INSTALLING THE LED LIGHT KIT NOTE: NOTE: Before starting installation, make sure power is turned off at the circuit breaker. 1. Remove 1 of 3 screws from the mounting plate and loosen the other 2 screws. (Do not remove) 2. While holding the LED light kit under the fan motor assembly, make the 2-pin wire connections: (Fig. 19) - White to white - Black to black 3. -
Page 19: Installing The Glass Shade
INSTALLING THE GLASS SHADE Step 1. Raise glass shade up against bottom of fan housing and secure it to the fan by turning the glass shade clockwise until snug. DO NOT OVERTIGHTEN. (Fig. 20) NOTE: NOTE: The aluminum cover included with your fan is an option to replace the glass for the light in the event that you prefer not to use the light feature of your fan. -
Page 20: Operating Your Fan
OPERATING YOUR FAN Restore power to ceiling fan and test for proper operation. 1. The fan 4-speed control is used to set the fan speed as follows: 0= Turns the fan off 1= High Speed 2= Medium High Speed 3= Medium Speed 4= Low Speed 2. - Page 21 Warm weather - (Forward) A downward airflow creates a cooling effect as shown in Fig. 22. This allows you to set your air conditioner on a warmer setting without affecting your comfort. Cool weather - (Reverse) An upward airflow moves warm air off the ceiling area as shown in Fig.
-
Page 22: Care Of Your Fan
CARE OF YOUR FAN Here are some suggestions to help maintain your fan. 4. Use a lint free lightly damp cloth or duster to remove dust from the blades. 1. Because of the fan's natural movement some connections may become loose. -
Page 23: Troubleshooting
TROUBLESHOOTING SYMPTOM SYMPTOM Fan will not start Fan Sounds Noisy SOLUTION SOLUTION Check fuses or circuit breakers. Allow a 24-hour "break-in" period. Most noises as sociated with a new fan go away during this time. Check wall control connections. Make sure all motor housing screws are snug. Check line wire connections to fan and switch wire connections in switch housing. - Page 24 SYMPTOM Fan Wobble SOLUTION NOTE: NOTE: All blade sets are grouped by weight. Because wood and plastic blades vary in density, the fan may wobble even though blades are matched. Make sure outlet box is secured to building structure, if necessary use the wood screws provided to further secure outlet box to joist. Make sure hanger bracket is secure to the outlet box, screws are tight.
-
Page 25: Specifications
SPECIFICATIONS Fan Size Speed Volts Amps Watts N.W. G.W. C.F. These are typical readings. Your actual fan may vary. They do not include amps and wattage used by the 0.183 7.49 52" 7.68 8.83 1.69' light(s). High 0.536 63.62... - Page 26 PERFORMANCE AND ENERGY INFORMATION FAN SPEED AIRFLOW POWER USE AIRFLOW EFFICIENCY (CFM)* (Watts) (CFM/Watt) 1400 7.49 186.92 High 4237 63.62 66.6 Estimated Ceiling fan airflow is measured in cubic feet per minute (CFM). Airflow 2,910 Yearly Energy Cost Power use is measured in watts. To maximize energy savings: •...
Need help?
Do you have a question about the minkaAire ALUMA and is the answer not in the manual?
Questions and answers