Related Manuals for Minka Group Minka Aire GEANT
Summary of Contents for Minka Group Minka Aire GEANT
- Page 6 1. Before you begin installing the fan, shut power off at the circuit breaker of the fuse box. 2. Be cautious! Read all instructions and safety information before installing your new fan. Review accompanying assembly diagrams. 3. Make sure that all electrial connections comply with local codes, ordinance, or National Electriacl Codes. Hire a qualified electrician or consulf a do-it-yourself wiring handbook if you are unfamiliar with installing electrial wiring.
- Page 7 SUPPORT DIRECTLY FROM BUILDING STRUCTURE. TO REDUCE THE RISK OF FIRE ELECTRIC SHOCK OR OTHER PERSONAL INJURY. MOUNT FAN DIRECTLY TO THE BUILDING JOIST USING THE WOOD SCREWS AND WACHERS PROVIED WITH THE FAN. THE WOOD SCREWS MUST GO THROUGH THE OUTLET BOX VIA THE KNOCK OUTS. CONSULT A QUALIFIED ELECTRICIAN IF DOUBT.
- Page 8 Hanger bracket (Hanger bracket Mounting hardware: support included) M6.5x89mm wood screws(3pcs) Standard downrod assembly (16”) Ø6.5x19mm Flat washers(3pcs) Hanger bracket plate 6.5mm Star washers(3 pcs) Canopy Wire nutes(3 pcs) Canopy cover Hex nuts(3 pcs) Coupling cover 1/4” spring washers(3pcs) Fan motor/ housing assembly 1/4”...
- Page 10 Step5. Remove hanger ball from downrod assembly by loosening set screws, removing the cross pin, and sliding ball off rod. (Fif. 9) Step6. Carefully feed fan wires up through the downrod. (Fig. 10) Thread the rod into the coupling until the holes line up holes and replace lock pin and hitch pin. Tighten set screws.
- Page 11 SAFETY CABLE DOWNROD RUBBER COVER OUTLET BOX HANGER BALL OUTLET BOX CANOPY REGISTRATION HANGER SLOT DOWNROD BRACKET SAFETY CANOPY COVER PLATE CABLE FLAT COUPLING COVER FLAT WASHERS WASHERS SPRING HITCH PIN STAR WASHERS WASHERS LOCK PIN SCREWS KNOCK OUT HEX NUTS WOOD WASHERS FIG.
- Page 13 4 Pin Connector for motor 2 Pin Connector...
- Page 15 WHEEL Attach the fan wheel to the motor assembly and tighten with 8 screws. (Fig. 16) (C) Notice “UP” label on fan wheel. The Fan Wheel is not reversible. (Fig.16-1)
- Page 16 Attach 8 screws at the wheel as FIG.17. Snug the screw. Do not tighten. Attach the blade holder to key slot hole as FIG.18 shown, then tighten screws, FIG. 19-1 repeat all 8 blade holder. Tighten all D and E screws as FIG.19 shown. Wheel Screws FIG.
- Page 17 Insert blade tips at the end of each blade and secure with screw as shown in (Fig. 20)(G) Install the blade and tighten with screws and washers supplied as shown in (Fig. 21)(F) Notice “THIS SIDE UP” label on fan blades. The fan blades are not reversible.
- Page 19 INSTALLING THE SWITCH COVER Raise the switch cover and secure it to the fan by turning the cover clock wise until snug. DO NOT OVERTIGHTEN. (Fig. 23)
- Page 27 0.09 0.15 26.29 30.84 0.25 16.5 4.919 0.39 28.0 0.55 35.0 0.64 49.0...
- Page 28 4630 890.38 6140 639.58 7497 16.5 454.36 8990 321.07 28.0 10105 35.0 288.71 11160 49.0 227.76...
Need help?
Do you have a question about the Minka Aire GEANT and is the answer not in the manual?
Questions and answers