Advertisement
The One-of-a-kind Highly Integrated Fanless 10.1" RISC POS Terminal
Jumper Setting
Cash Drawer Control
Selection
1
1
Drawer2
Drawer1
(default)
Cash Drawer Power
Selection
1
1
24V
12V
(default)
Inverter Voltage
Selection
2
6
2
6
1
5
1
5
12V
5V
(default)
LVDS Voltage Selection
JP17
JP15
6
1
2
5
3.3V
(default)
1
2
5
6
2
6
1
5
5V
5
6
1
2
JP17
12V
5
6
1
2
LVDS Panel Input Voltage
Selection
1
1
HW Enable
SW Enable
(default)
Touch Panel Signal
Interface Selection
1
USB5 Connector
(default)
CAUTION! Danger of explosion may occur if the battery is replaced incorrectly. Replace batteries only with the same or equivalent type recommended by the manufacturer.
Dispose the used batteries according to the manufacturer's instructions.
The following messages are reminders for safety on how to protect your systems from damages and to
extend a long life of the system.
1. Check the Cable Voltage
• Make sure the range of operating voltage between AC 100~240V. Otherwise, the system could be
damaged.
2. Environmental Conditions
• Place your PA-3211 on a sturdy, level surface. Be sure to allow enough space to have easy
access around the system.
• Avoid extremely hot or cold place to install the system.
• Avoid exposure to sunlight for a long period of time or in an airtight space.
• Avoid the system from any heating device or using it outdoors in a cold winter day.
• Bear in mind that the operating ambient temperature is from 0~35°C (32~95°F).
• Avoid moving the system rapidly from a hot place to a cold one and vice versa for condensation
may come from inside of the system.
• Place PA-3211 in strong vibration(s) may cause hard disk failure.
• Don't place the system close to any radio active device in case of signal interference.
3. Handling
• If the system isn't fully in DOS mode, adjust BIOS setting as the instruction:
Advanced Chipset Feature → Boot display → choose "LFP".
• Avoid putting heavy objects on top of the system.
• Don't turn the system upside down. This may cause the hard drive to malfunction.
UART1 Voltage
Selection
6
5
6
5
6
5
2
2
1
2
1
2
1
5V
RI
12V
(default)
UART3
DC_IN1
DRW1
1
JP8
UART3_1
1
UART1
JP7
OUT_24V
OUT_12V
OUT_5V
USB3
USB0
I2C
JP5
1
USB5
JP6
1
LED1_1
Safety Precaution
UART0 Voltage
Selection
1
1
2
1
2
6
2
2
2
6
5
6
6
5
5
2
RI
12V
5V
RI
(default)
(default)
VGA1
CN_LAN1
6
5
2
1
1
6
2
2
1
5
6
USB1_2
UART0
6
5
2
1
JP_USB1
JP10
1
1
JP9
1 2
JP15
1
JP14
5
6
JP17
JP4
1
6
5
1
2
LVDS1
USB4_2
SW2
• Don't allow foreign objects to fall into this product.
• If water or other liquid spills into this product, unplug the power cord immediately.
4. Good Care
• When the outside of the case is stained, remove the stain with a neutral washing agent with a dry
cloth.
• Never use strong agents such as benzene and thinner to clean the system.
If heavy stains are present, moisten a cloth with diluted neutral washing agent or with alcohol and
then wipe thoroughly with a dry cloth.
• If dust has been accumulated on the outside, remove it by using a special made vacuum cleaner
for computers.
• Don't contact the surface of capacitive touch before entering your operation system, or capacitive
touch may have position problems for electrostatics interface.
• Don't exchange the M/B battery by yourself or serious damage may incur.
CAUTION! Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent
type recommended by the manufacturer. Dispose of used batteries according to the manufacturer's
instructions.
WARNING! Some internal parts of the system may have high electrical voltage. And therefore we strongly
recommend that qualified engineers can open and disassemble the system. The LCD and Touchscreen are
easily breakable, please handle them with extra care.
PA-3211
UART3 Voltage
UART2 Voltage
Selection
Selection
5
6
5
6
5
1
2
1
2
1
2
1
5
6
5V
12V
RI
(default)
MICRO_SD1
ADFU Mode
UPDATE
USB1_2 / USB1 Selection
JP18
1
LED1_2
6
2
USB1_2
Connector
USB2_2 / USB2 Selection
6
5
6
1
2
JP_USB2
2
USB2
Connector
M_PCIE
SW1
SW5
Connector
UART5 Voltage Selection
SW3
2
1
JP_COM5
1
5
6
UART5
1
2
UART2
5
6
5
JP_COM2
(default)
LINE_OUT1
Inverter Backlight Enable
SPK1
2
6
JP16
1
5
INV1
All Rights Reserved. Copyright 2017
1
2
1
2
2
6
5
6
5
12V
5V
Image Detection
Selection
1
1
USB HUB
Function
(default)
6
5
5
2
1
1
USB1
Connector
(default)
5
6
5
1
1
2
USB2
USB2_2
Connector
(default)
Mini PCIE USB
Selection
1
1
USB4_2
Wi-Fi by USB
(default)
2
2
1
2
1
2
6
6
5
5
6
RI
12V
5V
Selection
1
1
3.3V
5V
(default)
All Right Reserved Copyright 2012
Advertisement
