Page 2
Edition Notes The Strike Array 2 User Manual includes a description, safety precautions, installation, programming, operation and maintenance instructions for the Strike Array 2 as of the release date of this edition. Trademarks Chauvet, the Chauvet logo and Strike are registered trademarks or trademarks of Chauvet & Sons, LLC (d/ b/a Chauvet and Chauvet Lighting) in the United States and other countries.
Any reference to data or power connections in this manual assumes the use of Seetronic IP rated cables. The term “DMX” used throughout this manual refers to the USITT DMX512-A digital data transmission protocol. Strike Array 2 User Manual Rev. 4...
• In the event of a serious operating problem, stop using immediately. If a Chauvet product requires service, contact Chauvet Technical Support. Strike Array 2 User Manual Rev. 4...
LEDs, contributing to shorter lifespans if always used at full intensity. The average LED lifespan is 40,000 to 50,000 hours. To extend LED lifespan, maintain proper ventilation around the product, and limit the overall intensity. Strike Array 2 User Manual Rev. 4...
2. Introduction Description The Strike Array 2 is an outdoor-ready audience blinder powered by two 100 W warm white LEDs housed in independently focusable pods. An emulated “amber shift” warms the color temperature of the light as it dims to deliver a classic tungsten look. Its variable PWM and high CRI make it ideal for broadcast applications.
42 mm 8.89 in 225.8 mm 6.42 in 163 mm 18.58 in 472 mm 15.09 in 383.3 mm 7.61 in 193.3 mm 4.55 in 115.6 mm 2.05 in 52 mm 0.51 in 13 mm Strike Array 2 User Manual Rev. 4...
3. Setup AC Power The Strike Array 2 has an auto-ranging power supply and it can work with an input voltage range of 100 to 240 VAC, 50/60 Hz. To determine the product’s power requirements (circuit breaker, power outlet, and wiring), use the current value listed on the label affixed to the product’s back panel, or refer to the product’s specifications chart.
Setup USB Software Update The Strike Array 2 allows for software updates with a USB device using the built-in USB port. To update the software using a USB flash drive, do the following: 1. Power on the product, and plug the flash drive into the USB port.
When rigging the product onto a truss, use a mounting clamp of appropriate weight capacity. Procedure The Strike Array 2 comes with a bracket to which a clamp can be attached directly. Mounting clamps are sold separately. Make sure the clamps are capable of supporting the weight of this product. Use at least two mounting points per product.
Setup Multi-Product Mounting The Strike Array 2 has an interlocking system to connect multiple Strike Array 2 or STRIKE Array 4 products together, vertically or horizontally. Make sure the mounting clamps are capable of supporting the weight of the product. For our Chauvet line of mounting clamps, go to http://trusst.com/productcategory/...
When using the omega bracket, never hang more than 16 cells vertically from a single mounting point. • When not using the omega bracket, never hang more than 8 cells vertically from a single mounting point. Strike Array 2 User Manual Rev. 4...
When mounting products attached in series, use omega brackets in the back position to create a spine. This will prevent any motion which may damage the products. Mounting clamps Omega brackets Pole or pipe for stability Strike Array 2 User Manual Rev. 4...
<ENTER> Navigates downward through the menu list or decreases the numeric value when in a function Control Options Set the Strike Array 2 starting address in the 001–512 DMX range. This enables control of up to 64 products in the 8-channel 8 Ch personality.
Unit shows “No such file!” _ _ _ _ _ _.CHL Selects an update file for this and connected Update Multiple Strike Array 2 products, or shows “No such Firmware Units file!” _ _ _ _ _ _.CHL Other Fixture...
1. Go to the Red Shift main level. 2. Select from On or Off. Master Slave To set the Strike Array 2 product to master or slave mode: 1. Go to the Master/Slave main level. 2. Select from Master (sends control signal) or Slave (receives control signal).
6. Softly drag any dirt or grime to the outside of the transparent surface. 7. Gently polish the transparent surfaces until they are free of haze and lint. Always dry the transparent surfaces carefully after cleaning them. Strike Array 2 User Manual Rev. 4...
For warranty terms and conditions and return information, please visit our website. For customers in the United States and Mexico: www.chauvetlighting.com/warranty-registration. For customers in the United Kingdom, Republic of Ireland, Belgium, the Netherlands, Luxembourg, France, and Germany: www.chauvetlighting.eu/warranty-registration.. Strike Array 2 User Manual Rev. 4...