Nexa AN-179 - Built-In Receiver Manual

Table of Contents

Contents

1 TECHNICAL DATA
2 INTRODUCTION
3 OVERVIEW
4 INSTALLATION
5 CONNECT TO A Z-WAVE NETWORK
6 USE
7 SAFETY AND INFORMATION
8 WIRING DIAGRAM
9 Z-WAVE PLUS INFO
10 VERSION
11 AGI (ASSOCIATION GROUP INFORMATION) TABLE
12 BASIC
13 NOTIFICATION
14 CONFIGURATION
15 COMMAND CLASSES
16 Documents / Resources
- 16.1 Download manual

TECHNICAL DATA

AN-179
Power source	220-240 V~50 Hz
Max. charge	2500 W R
Frequency	Z-Wave (868.42 MHz)
Range	up to 30 m
Power consumption	< 1 W (standby)
IP rating	Indoor use
Dimensions (W x H x D)	43 x 42 x 16 mm

INTRODUCTION

Built-in receiver for permanent installation. Small, compact size for placing in a junction box or switchbox. Can be connected to existing switch. The receiver needs both phase and neutral. The receiver is fully compatible with the Z-Wave Plus standard.

OVERVIEW

INSTALLATION

Make sure that the conductors are powered down by turning off the power in the distribution box.

Connect Phase to L and IN, Load/Ignition wire to LS and Zero Conductor to N.
AN-179 can be connected to power switches, even momentary switches, for control, also see wiring diagram.
Please note that switches connected to AN-179 must be potential free, i.e. fully insulated from 230 V.

CONNECT TO A Z-WAVE NETWORK

Auto-inclusion

When AN-179 is powered up for the first time and a NODE ID has not been assigned, it starts in auto-inclusion mode.

Put the Z-Wave controller in inclusion mode (see the controller's manual)
Connect AN-179 to voltage and the unit is included.

Manual Inclusion

Put the Z-Wave controller in inclusion mode (see the controller's manual)
Press 3 times on the Link button within 1.5 seconds

Exclusion

Put the Z-Wave controller in exclusion mode (see the controller's manual)
Press 3 times on the Link button within 1.5 seconds.

Restore to factory settings

Press 3 times on the Link button within 1.5 seconds.
Within 1 second after step 1 above, press and hold down the link button until the LED goes out, approx. 5 seconds.
Node ID is deleted and the unit restored to factory settings.

USE

Control using Z-Wave controller: Consult the manual for your Z-Wave controller for information about how to control your receiver.

SAFETY AND INFORMATION

LOAD	MAX POWER
Incandescent bulbs % Resistive loads (230 V)	2500W /220-240 V
Halogen lights (230 V)	1200W / 220-240 V
LED & Low energy bulbs (230 V)	320 W / 220-240 V (40 W x 8)

Read through the entire instruction first. Engage a professional if so required. Nexa cannot be held liable if the product is used for any purpose other than the one for which it is designed, or if there is failure to comply with the instruction.

burn hazard shock hazard
Never connect bulbs or equipment exceeding the receiver's maximum stated load – this may lead to faults, short-circuiting or fire. Do not attempt to repair the product.
The product contains no repairable parts.

Range indoors:
up to 30 m (optimal conditions). The range is very dependent on the local conditions, for example, if there are metals in the vicinity. For example, the thin metal coating in energy glass with low emissivity has a negative influence on the range of the radio signals. There may be restrictions on the use of the unit outside the EU. If appropriate, you should check that the unit complies with local regulations.

Max load:
burn hazard shock hazard
Never connect lights or equipment that exceed the receiver's maximum load. This could lead to faults, shortcircuiting or fire.

Life-support equipment:
Never use Nexa's products with lifesupport equipment or other devices where faults or interference could have life-threatening consequences.

Interference:
All wireless units can suffer from interference that can affect the performance and range. For this reason, the minimum distance between two receivers should be at least 50 cm

Repair:
Do not attempt to repair the product. It does not contain any repairable parts.

Waterproofing:
shock hazard The product is not waterproof. Make sure it is dry at all times. Damp causes the electronics inside to corrode and this could lead to short-circuiting, faults and a risk for electric shocks.

Cleaning:
Clean the product with a dry cloth. Do not use chemicals, solvents or strong cleaning agents.

Environment:
Do not expose the product to intense heat or cold, because it could damage or shorten the service life of the electric circuits.

WIRING DIAGRAM

Z-WAVE PLUS INFO

Role Type	Node Typer	Installer Icon	User Icon
Slave Always On	Z-Wave Plus node	On/Off Power Switch	On/Off Power Switch

VERSION

Protocol Library	3 (Slave_Enhance_232_Library
Protocol Version	3.95 (6.51.02)

AGI (ASSOCIATION GROUP INFORMATION) TABLE

Group	Profile	Command Class & Command (List) N bytes	Group Name (UTF-8)
1	General: NA	Binary Switch Report, Notification Report, Device Reset Locally Notification	Lifeline
2	Control: Key1	Basic Set	On/Off control Button 1