Advertisement
Quick installation guide EJLR-1000!
!
NEXA EJLR-1000
Important information!
!
COMPATIBILITY!
This receiver works with all Nexa transmitters including Nexa Gateway.!
!
!
FUNCTIONALITY!
Build-in receiver for controlling (up/down/stop) 230 V, 12 V and 24 V electric motors (sunblinds,
screens, etc.)!
!
!
TECHNICAL SPECIFICATIONS
• Power supply input !
• Maximum load !
• Replaceable fuse!
• RF frequency!
• RF range!
• Standby power consumption!
• Memory addresses!
!
!
WIRELESS RADIO SIGNAL!
!
• The 433.92 MHz radio signal passes through walls, windows and doors.!
• Indoor range: up to 30 m. Outdoor range: up to 70 m. (optimal conditions)!
• The range is strongly dependent on local conditions, such as the presence of metals. For
example, the thin metal coating in Low-emissivity (Low-E) glass has a negative impact on the
range of radio signals.!
• There may be restrictions on the use of this device outside the EU. If applicable, check whether
this device complies with local directives.!
!
!
Read the "important information" booklet before installing this
product!
Not following the safety instructions may be dangerous and faulty
installation will invalidate any warranty that may apply to this product.!
!
!
!
!
!
!
!
220-240 VAC 50 Hz
!
!
500 Watt
20 mm 5A (T5A, H250V)
433.92 MHz
Up to 30 m indoor/up to 70 m outdoor (optimal conditions) !
0.5 Watt
6
Sida
1
av
7
Advertisement
Table of Contents
Related Manuals for Nexa EJLR-1000
Summary of Contents for Nexa EJLR-1000
-
Page 1: Important Information
Important information! COMPATIBILITY! This receiver works with all Nexa transmitters including Nexa Gateway.! FUNCTIONALITY! Build-in receiver for controlling (up/down/stop) 230 V, 12 V and 24 V electric motors (sunblinds, screens, etc.)! - Page 2 Without prior written permission, reproducing or copying is prohibited. Information in these documents is subject to change without prior notice. Check www.nexa.se for updates.! Nexa Trading AB declares that this product is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC (R&TTE).!
- Page 3 Switch off the mains power (electric meter box) before installing this! product! Remove the existing switch! Detach the existing switch and disconnect the wires. The existing wall switch is replaced by this product and can no longer be used. Consult the supplier of your sun blind system when in doubt about motor type and wire colors.! Connect 230V power supply!
- Page 4 Connect motor wiring How to connect the motor wiring! depends on the type of motor: - Read step 4A for a 230V motor. - Read step 4B for a 12-24V motor. ! - Read step 4C for a motor with a momentary switch.! Connect 230V motor ...
- Page 5 1 sec. will be active for 15 seconds and the LED-indicator will blink slowly.! Assign Nexa transmitter code! While the learn-mode is active, send an ON-signal with any Nexa transmitter to assign the code to the receiver’s memory.! Code confirmation ...
- Page 6 The module contains 2 voltage-free contacts:! ]. In the neutral position, the contact [COM] is not switched. After an on/off signal from a Nexa transmitter, [COM] switches either to the left or the right [ ] contact. After 2 minutes, the COM contact switches back to its neutral position.!
- Page 7 1. Press the learn-button for 1 second. The learn-mode will be active for 15 seconds and the LED-indicator will blink slowly. ! 2. While the learn-mode is active, send an OFF-signal to delete the code of a specific Nexa transmitter. ! 3.
Need help?
Do you have a question about the EJLR-1000 and is the answer not in the manual?
Questions and answers