Hardware List of Luca Trundle IMAGE DESCRIPTION Part SKU# 1996-1(8) Bolt and nut M8*70mm 1996-2(2) Bolts M4*20mm 1996-3(4) Dowel Ø8*40mm 1996-4(14) Screws 8#*30mm 1996-5(1) Handle 1996-6(1) Allen key 60*22*4mm Note: Screwdriver will be prepared by yourshelf. THE HARDWARE IS LOCATED IN THE PACKING ITEM NOTE: MUST TIGHTEN SCREWS PERIODIACLLY.
Page 5
STEP 1: Firstly, please locate Side Rail (C) to Front (A), Back (B) Before assembly: Move the nut out by dowel (3) . Fasten Side Rail (C) by (Bolt+nut) (1). 1=8 Pcs 3=4 Pcs STEP 2: Please fasten slats (D) by screw (4) into corresponding holes. 4=14 Pcs...
Page 6
STEP 3: Assemble the handle (5) into Front (A) 2=2 Pcs 5=1 Pc That's it ! You've finished assembling your item. Thank you!
Page 8
Ensure thickness of mattress does not exceed 6" and mattress is at least 5" below upper edge of guardrails. Ensure thickness of mattress does not exceed 6" for lower bunk. REPLACEMENT PARTS Replacement parts, including additional guardrails, may be requested from Living Spaces, usually at a cost.
Page 9
Always use the ladder or Stairway Chest for entering and leaving the upper bunk. You will buy ladder/Stairway as options.
Page 11
BOX 3- FL/FL SIDE/GUARD RAILS/SLAT SUPPORT BUNK BED PART SKU# IMAGE DESCRIPTION 1987FF-C-W:(White) Upper Rails 1987FF-C-B:(Blue) 1987FF-C-G:(Grey) 1987FF-D-W:(White) 1987FF-D-B:(Blue) Guard rails 1987FF-D-G:(Grey) 1987FF-E-W:(White) Guard rail 1987FF-E-B:(Blue) supports 1987FF-E-G:(Grey) Lower 1987FF-F-W:(White) 1987FF-F-B:(Blue) back rail 1987FF-F-G:(Grey) Lower 1987FF-G-W:(White) 1987FF-G-B:(Blue) Front Rail 1987FF-G-G:(Grey) Slat supports 1987FF-H...
Page 12
Hardware List of Luca Full-Full Bunk Bed IMAGE DESCRIPTION Part SKU# 1987FF-1(16) Bolt and nut M8*90mm 1987FF-2(6) Bolts M8*35mm Screws Ø6.5*83mm 1987FF-3(8) 1987FF-4(16) Dowel Ø8*40mm 1987FF-5(28) Screws 8#*30mm 1987FF-6(4) Metal dowel Ø10*100mm 1987FF-7(1) Allen key 60*22*4mm Stickers 1987FF-8(6) Note: Screwdriver will be prepared by yourshelf. THE HARDWARE IS LOCATED IN THE PACKING ITEM NOTE: MUST TIGHTEN SCREWS PERIODIACLLY.
Page 14
STEP 1: Assembly Rail (C): Please locate two rails (C) to Ends (A) by Dowel (4) firstly, and then fasten gradually by Bolt+nut (1) BUT NO TIGHTEN. Assembly Guard Rail (D): Please locate Guard rails (D) to Ends (A) by Dowel (4) firstly, and then fasten gradually by Bolt (3).
Page 15
STEP 3: Place the slat support (H) to Upper bunk STEP 4: Please fasten slats (I) by screw (5) into corresponding holes. 5=14 Pcs...
Page 16
STEP 5: Assembly Rail (F), (G): Please locate two rails (F) , (G) to Ends (B) by Dowel (4) firstly, and then fasten gradually by Bolt+nut (1) . Pay attention to rail orientation . Distinguishing Back Rail (F) and Front Rail (G)! 4=4 Pcs 1=8 Pcs STEP 6: Place the slat...
Page 17
STEP 7: Please fasten slats (I) by screw (5) into corresponding holes. 5=14 Pcs STEP 8: Assemble the upper bunk to lower bunk by Metal dowel (6). 6=4 Pcs...
Page 18
Notice: Using the color stickers (8) to fill the empty holes on frames. 8=6 Pcs Combining with Ladder ( Option 1). Attaching the ladder to Guard rail by Screw and to Lower Side Rail by bolt (these hardware are included in Ladder box).
Page 19
Combining with Stairway Chest ( Option 2). Please attach the Stairway Chest to Bunkbed by metal bracket and screw ( these hardware are included in Stairway box). Please place Stairway Chest is next to Bunkbed Side and wall.
Page 20
Option 1: Option 2: That's it ! You've finished assembling your item. Thank you!