Maintenance - Worx WG173E.9 Manual

Safety ON/OFF Switch
WARNING The cutting head
!
continues to rotate after the
trimmer has been switched off; wait
until it has completely stopped then
lay down the tool.
Make sure that line
WARNING !
is fed out before operation.
Make sure motor is up to full speed
before trimming or edging.
Adjusting the Shaft
Adjusting the Auxiliary handle
-Using the Flower Guard
Pull out the flower guard before
operation.
Trimming
Adjusting the Trimmer Head
-
NOTE The trimmer head must be
:
locked as Fig. I3.
- Trimming / Mowing
NOTE :
• For trimming/mowing Fig. J1,
please mount the wheels following
Fig. B2. For trimming in Fig. J2,
please mount the wheels following
Fig. B3.
• You could also use the machine
without the guide wheels on the
guard when trimming
.
Edging
- Main handle rotation
"Secure the lower housing and guard
in place (using your foot or hand).
Pull up on the telescopic shaft and
turn clockwise 90 degrees.
Release, and the shaft will automati-
cally lock into edging mode."
Changing the tool into the Edging
-
mode
Edging
-
Command feeding the line
NOTE Press as needed.
:
Manually feeding the line
Replacing the trimmer Spool
Manually winding the line
Cordless Grass Trimmer
LINE FEEDING/WINDING
INSTRUCTION
1. Automatic line feed system
When initially switching on the trimmer, a small
See Fig. E
length of line is fed out. Each time the tool is started
from rest it will advance about 0.25 inches of
trimmer line.
A 'clattering' noise will be heard when the lines hit
the Line Cutter. DO NOT BE ALARMED. This is quite
normal. After about 5 seconds the line will be cut to
See Fig. F
the correct length and the noise will reduce as the
motor gains full speed.
See Fig. G
If the noise of the line being cut can't be heard, more
line will need to be fed out.
See Fig.
To feed more line, it is first necessary to allow the
H1,H2
trimmer to stop completely; it must come to a
complete rest, then restart, allowing the motor to
reach full speed.
Repeat above until you hear the line hitting against
See Fig. I1, the Line Cutter.
I2, I3
2.
Your trimmer is equipped with a Command Feed
System. For efficiently feeding the line, just press the
command feed button while the machine is running
until you hear the 'clattering' noise of the line cutting.
The motor will shut off when pressing the Command
See Fig. J1, J2
Feed button and will restart when releasing the
button. During that process the line will automatically
feed additional line for cutting.
3. Manually feeding the line (See Fig. M)
Turn off the trimmer and remove the battery. If
required, line can be fed out manually. To operate,
press and release manual Line Feed Button, while
gently pulling out the line until it is long enough to
reach the Line Cutter. If the line extends past the Line
Cutter, too much line has been fed out. If too much
See Fig. K1,
line is fed out, remove the Spool Cap and turn Spool
K2
counter-clockwise until the line is at the desired
length.
4. Manually winding the line
See Fig. K3,
( See Fig. O1, O2, O3, O4)
K4, K5
Take approximately 10ft (3m) of line. Insert 5/8
inch (15mm) of line into the Spool holes and wind
See Fig. K6
line in the direction of the arrows on the top of the
Spool. Leave approximately 4 inches (100mm) of line
See Fig. L
unwound and place into the cleat. Ensure that the
line is neatly coiled on the Spool. Failure to do so will
See Fig. M
impair the efficiency of the automatic line feed. Then
fit the Spool as shown in Fig. N1, N2, N3
See Fig. N1,
N2, N3
See Fig. O1,

6. MAINTENANCE

O2, O3, O4
After use, disconnect the battery from the tool and
check for damage.
TM
(See Fig. L)
15
EN