Subscribe to Our Youtube Channel
Related Manuals for BIOS Diagnostics BD252
Summary of Contents for BIOS Diagnostics BD252
- Page 1 BLOOD PRESSURE MONITOR Insight Instruction Manual Model: BD252 Go to biosmedical.com for a FREE Log Book! Advancing Home Monitoring Since 1973 biosmedical.com 10.17.22...
- Page 2 Excellence from Angelique Berg, CEO of Hypertension Canada Trusted by Canadians for 3 Generations At BIOS Diagnostics™, we are proud of our legacy in blood pressure monitoring in Canada. From the early 1930s to 1987 we manufactured “Tycos” brand professional blood pressure equipment for doctors and hospitals in Canada.
-
Page 3: Table Of Contents
Blood Pressure Monitor - Insight Instruction Manual Table of Contents 1. Introduction 1.1 Features 1.2 Important Information 1.2A Safety Information 1.2B Care of the Device 1.2C Comparing Readings to Other Blood Pressure Devices 1.2D Calibration 1.3 What Do Your Numbers Mean? 1.4 Normal Blood Pressure Values 1.5 Common Blood Pressure Questions and Answers 2. -
Page 4: Introduction
Indications for Use: This blood pressure monitor (BD252) is intended to measure the systolic/diastolic pressure, and pulse rate of an adult individual by using a non-invasive oscillometric technology. This device is designed to be portable, and used in both home and professional environments for every day blood pressure monitoring. - Page 5 • If you are undergoing medical treatment and receiving medication, consult your doctor to determine the most appropriate time to measure your blood pressure. Never alter the dosages of any medication without direction from your doctor. • Your blood pressure depends on several factors, such as age, gender, weight and physical condition. It also depends on the environment and your state of mind at the time of measurement.
-
Page 6: B Care Of The Device
1.2B Care of the Device For prolonged life of your blood pressure monitor, note the following instructions: • Do not drop or bang the unit. Prevent sudden jerks, jars, or shocks to the device to prevent damage. • Do not insert any foreign objects in any device openings or vents. •... -
Page 7: What Do Your Numbers Mean
1.3 What do your Numbers Mean? Blood pressure is the pressure in your blood vessels while blood circulates throughout your body. High blood pressure or “Hypertension” is the pressure at which ones normal average blood pressure is considered too high and other health risks including: heart attack, stroke, dementia, kidney failure, heart disease and erectile dysfunction may occur. -
Page 8: Common Blood Pressure Questions And Answers
1.5 Common Blood Pressure Questions and Answers a) Why is my blood pressure reading always different? Your blood pressure changes constantly. It is quite normal for blood pressure to fluctuate as much as 50 mmHg throughout the day. Blood pressure is normally lowest at night, but increases during waking hours when the stress and activities of everyday life are highest. -
Page 9: About The Lcd Screen
Upper Arm Cuff: Wide range cuff for arm circumference 24 - 43 cm or 9.4” - 17”. Cuff Connection: Insert the cuff connector into the opening provided on the left side of the monitor as shown in the diagram. 2.2 About the LCD Screen The LCD screen displays the systolic and diastolic blood pressure measurements along with your heart rate. -
Page 10: Using The Ac/Dc Power Adapter
2.4 Using the AC/DC Power Adapter You may also operate this monitor using the included AC/DC adapter. Use only the included adapter to avoid damaging the unit. 1. Ensure that the AC/DC adapter and cable are not damaged. 2. Plug the adapter cable into the AC/DC adapter port on the top of the blood pressure monitor. -
Page 11: Obtaining Accurate Measurements
3.3 Obtaining Accurate Measurements Your blood pressure can vary based on numerous factors, physiological conditions, and your surroundings. Follow these guidelines to obtain accurate and error-free measurements of your blood pressure and pulse rate. 3.3A Tips on Taking Accurate Measurements In the morning before breakfast, 2 hours after dinner, before taking Empty bladder (if necessary). -
Page 12: C Fitting The Wide Range Cuff
3.3C Fitting the Wide Range Cuff NOTE: Visit www.biosmedical.com for a video that illustrates how to properly fit the cuff. a) Putting the cuff velcro side down on a table, the words on the cuff should Metal Ring be facing right side up. Put the end of the cuff (with fastener) through the metal ring, making the cuff a cylinder. -
Page 13: Protocol Software (7D Mode)
h) For those who cannot put the cuff on the left arm, put it on the right arm as shown. More than 6 consecutive measurements will cause blood accumulation in the lower arm which will affect the measuring results. To improve reading accuracy, raise the arm being measured, squeeze and relax your hand several times, then take another measurement. - Page 14 Take: 2 measurements, 1 minute apart • Empty bladder (If necessary) • 2 hours after dinner, before taking medication • Sit with back supported and measurement arm resting on a table. Sit with feet flat on the floor. • Avoid coffee and smoking within the hour, and no exercise 30 minutes before measuring.
-
Page 15: General Mode
3.5 General Mode In General Mode, a user can take blood pressure measurements outside of the Protocol Software (7D Mode). 1. When the monitor is OFF, press the SET button, 7D Mode will appear on the monitor. Press the MEM button to switch between 7D Mode and General Mode. Press SET to confirm. 2. -
Page 16: Memory Recall
3. Open the MediLink App. You will need to register and create a password. 4. With the app open to the blood pressure and heart rate tab select ‘Add Bluetooth BP Monitor’. (Figure 1) 5. Select your device from the list of monitors. (Figure 2) 6. -
Page 17: A Recalling Memory In General Mode
3.9A Recalling Memory in General Mode First select General Mode, then turn the monitor OFF by pressing the START/STOP button. While the monitor is OFF, press the MEM button to see the most recent measurement value. Subsequent measurements can be displayed one after the other by continuously pressing the MEM button. -
Page 18: Clear Measurements From Memory
Reasons why the Protocol Software is displaying Not enough measurements have been saved in memory. For the Protocol Software to work correctly there needs to be 28 measurements saved in memory, 4 measurements taken for 7 days. 3.10 Clear Measurements From Memory If you are sure that you want to permanently remove all stored memories, first choose the mode you want to delete the memory from, then press the SET button 14 times until “... -
Page 19: Error Messages / Malfunctions
4. Error Messages / Malfunctions If an error occurs during a measurement the LCD displays the corresponding error code. Error Possible Cause Remedy Ensure that the cuff is worn correctly and measure Weak signal or a sudden change in again. Avoid movement or talking when the cuff is being pressure inflated. -
Page 20: Care And Maintenance
6. Lifetime Limited Warranty This BIOS Diagnostics blood pressure monitor has a lifetime limited warranty to be free of defects from the date of purchase. Only applicable to the original owner. This warranty does not include the inflation system including the cuff and inflation bladder. -
Page 21: Technical Specifications
Should repair be necessary, return the unit with all component pieces. Enclose proof of purchase and $5.00 for return shipping and insurance. Ship the unit prepaid and insured (at owners option) to: THERMOR LTD. Repair Department 16975 Leslie Street Newmarket, ON L3Y 9A1 www.biosmedical.com Email: support@biosmedical.com Please include your name, return address, phone number, and email address.
Need help?
Do you have a question about the BD252 and is the answer not in the manual?
Questions and answers