Skan Holz Kumla 760749 Manual

Kumla 600 x 400cm
Important information
Please check the construction set for completeness using the position list in good time before starting con-
struction or commissioning your construction team. If individual parts are defective or missing, we will deliver
these as quickly as possible. However, we cannot refund the costs for any resulting construction delays to a construc-
tion company.
Please understand that we cannot assume any guarantee for the following defects:
- incorrect storage before assembly
- incorrect anchoring with the ground or inadequate foundation (foundation according to statics)
- damage due to erection errors, e. g. the house is not level or not right-angled
- damage through a higher level of snow burden than statically envisaged. Recommendation: lad relief of the roof
by removing the snow layer
- storm damage (insurance cases) or violent destruction
- damage through any alteration to the design by the client
- natural formation of cracks, branch holes, twisting, decolouration or similar modification (natural process; has no
influence on the statics)
Storage information until construction :
- store pallet on a level and dry surface.
- Protect from exposure to sunlight and the influences of weather ; wood can warp drastically in a loose condition!
Maintenance tips:
Please observe the attached information sheet "Care instructions/Colour treatment".
General tips:
-
The packaging foil can be used to keep moisture out of the house. It is laid according to the ground area of the hou-
se under the main bearing.
-
If a felt is used as a roof cover, we recommend two layers.
-
A possibly desired installation of a rain gutter must be done by the building contractor; for this the roofing boards must
be cut to the right length.
-
Foundation according to the structural calculations (not included in the scope of delivery): concrete C25/30, each
2 Ø 12 top and bottom, brace mat R188A (alternatively brace Ø 6/20cm). Anchoring of the floor beams (in the buil-
ding) on the strip foundation using bolts M12, e < 60cm. The base bearings in the storeroom of the house must be
entirely flush.
-
The wooden parts of the building kit are delivered with a residual moisture content of about 15%.
Wood "works"! This means that the wooden parts will swell during prolonged damp weather and shrink (dry out) du-
ring prolonged dry periods. This only occurs in height or width, not lengthwise.
The block planks are firmly screwed to the vertical corner post during installation. This will not change its length, but
the horizontally attached planks change their height. If damp weather persists, the block planks can swell slightly
after completion. It is therefore important to leave 1mm clearance between the planks when fitting. Use the enclosed
spacer (to avoid unnecessary strains in the structure).
-
If the door cannot be closed properly, this can be adjusted by turning the hinges.
-
In winter, make sure that too much snow is removed from the roof so that heavy snow loads do
not cause damage to the roof structures.
Tips for assembly:
- Make sure that the foundation is even and frost proof.
- The foundation timbers of the building are proofed, but we still recommend installing a strip of roofing felt
between the foundation timbers and the foundation itself to prevent moisture rising from the soil into the timber (felt
not included).
- To start assembly, arrange the parts in numerical order next to the assembly site. You can identify the parts needed
for each step of the assembly process by their measurements (please see the list of parts).
- Keep the small parts (screws, nails, fittings, etc.) in their bags during the assembly process to stop them from getting
lost.
- We recommend that you use protective gloves and eyewear during the assembly process.
- Reserve 1-3 days for the assembly process.
- Some steps of the assembly require two people.
- Paint the wooden surfaces of the structure soon after assembly to protect it, and install roofing cover or sheeting onto
its roof (e.g. roofing felt).
© SKAN HOLZ Europe GmbH / D-21227 Bendestorf. Technical modifications reserved. All dimensions are approximate dimensions. 02/2023
760749
1