Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Chauvet DJ EZLink Par Q6BT ILS
Summary of Contents for Chauvet DJ EZLink Par Q6BT ILS
- Page 1 EZLink Par Q6BT ILS User Manual...
-
Page 2: Table Of Contents
IRC-6 Infrared Remote Control ..............IRC-6 Operation ......................11 Bluetooth Control ..................Master/Slave Mode ..................Master/Slave Mode (D-Fi USB)..............ILS Mode....................... 5. Maintenance................Product Maintenance ..................6. Technical Specifications ............Contact Us ..................Warranty & Returns..................EZLink Par Q6BT ILS User Manual Rev. 1... -
Page 3: Before You Begin
Electronically published by Chauvet in the United States of America. CHAUVET, the Chauvet logo, and EZLink Par Q6BT ILS are registered trademarks or trademarks of Chauvet & Sons LLC. (d/b/a Chauvet and Chauvet Lighting) in the United States and other countries. -
Page 4: Safety Notes
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Keep this User Manual for future use. If you sell the product to someone else, be sure that they also receive this document. EZLink Par Q6BT ILS User Manual Rev. 1... -
Page 5: Introduction
3-pin DMX in/ out Fuse Holder Bracket Power in/ out adjustment knob (2x) Battery D-Fi USB Port Product Dimensions 8 in 207 mm 3.4 in 86 mm 6.7 in 170 mm 9.6in 244 mm EZLink Par Q6BT ILS User Manual Rev. 1... -
Page 6: Setup
3. Setup AC Power The EZLink Par Q6BT ILS has an auto-ranging power supply, and it can work with an input voltage range of 100 to 240 VAC, 50/60 Hz. To determine the product’s power requirements (circuit breaker, power outlet, and wiring), use the current value listed on the label affixed to the product’s back panel, or refer to the... -
Page 7: Power Linking
Additional EZLink Par Q6BT ILS It is possible to power link up to 17 EZLink Par Q6BT ILS products on 120 VAC or up to 31 EZLink Par Q6BT ILS products on 230 VAC. The power-linking diagram corresponds to the North American version of the... -
Page 8: Mounting
Before mounting the product, read and follow the safety recommendations indicated in the Safety Notes. Orientation The EZLink Par Q6BT ILS may be mounted in any position; however, make sure adequate ventilation is provided around the product. Rigging • Before deciding on a location for the product, always make sure there is easy access to the product for maintenance and programming purposes. -
Page 9: Operation
Choosing a starting address that is too high could restrict the access to some of the product’s channels. The EZLink Par Q6BT ILS uses up to 8 DMX channels in a 8Ch DMX mode, which defines the highest configurable address to 505. -
Page 10: D-Fi Usb Connectivity
D-Fi USB Connectivity The EZLink Par Q6BT ILS is able to become a D-Fi wireless receiver/transmitter with the use of the D-Fi USB from Chauvet DJ. Simply set the product's DMX Personality and DMX Address, set the DIP switch D- Fi receiving/transmitting channel, then plug it into the D-Fi USB port. -
Page 11: Dmx Values
DMX signals from the controller. Preset Color Mode To run the EZLink Par Q6BT ILS on a static color, follow the instructions below: 1. Press <MENU> repeatedly until C-- shows on the display. 2. Press <ENTER>. -
Page 12: Sound Sensitivity
Operation Sound Sensitivity To set the sound sensitivity on the EZLink Par Q6BT ILS , do the following: 1. Press <MENU> repeatedly until SEnS shows on the display. 2. Use <UP> or <DOWN> to increase or decrease the sound sensitivity, from u 0–100. -
Page 13: Irc-6 Infrared Remote Control
Operation IRC-6 Infrared Remote Control The EZLink Par Q6BT ILS can be operated with the CHAUVET IRC-6. To enable IR wireless control, follow the instructions below. 1. Press <MENU> repeatedly until SEt shows on the display. 2. Press <ENTER>. 3. Press <UP> repeatedly until ir shows on the display. -
Page 14: Master/Slave Mode
Master/Slave Mode (D-Fi USB) The D-Fi USB allows a single EZLink Par Q6BT ILS product (the “master”) to control the actions of one or more EZLink Par Q6BT ILS products (the “slaves”) without the need of a DMX controller or DMX cables. The master (transmitter) product will be set to operate in standalone mode, while the slave (receiver) products will be set to operate in DMX mode. -
Page 15: Maintenance
Softly drag any dirt or grime to the outside of the transparent surface. Gently polish the transparent surfaces until they are free of haze and lint. Always dry the transparent surfaces carefully after cleaning them. EZLink Par Q6BT ILS User Manual Rev. 1... -
Page 16: Technical Specifications
Maximum External Temperature Cooling System 104 °F (40 °C) Convection I/O Connector Channel Range 3-pin XLR 4 or 8 Ordering Product Name Item Code UPC Number EZLink Par Q6BT ILS 10032010 781462223588 EZLink Par Q6BT ILS User Manual Rev. 1... -
Page 17: Contact Us
For warranty terms and conditions and return information, please visit our website. For Customers in the United States and Mexico: www.chauvetlighting.com/warranty-registration. For Customers in the United Kingdom, Republic of Ireland, Belgium, the Netherlands, Luxembourg, France, and Germany: www.chauvetlighting.eu/warranty-registration. EZLink Par Q6BT ILS User Manual Rev. 1...