Page 3
VERS.2015.05.19 Kit CDR 133 + CDM 163_MAN_EN Declaration of conformity The undersigned manufacturer: SAINT - GOBAIN ABRASIVES S.A. 190, BD. J. F. KENNEDY L-4930 BASCHARAGE Declares that this product: KIT CDR 133 + CDM 163 70184694704 « Drill Rigs »: Code : is in conformity with the following Directives : ...
VERS.2015.05.19 Kit CDR 133 + CDM 163_MAN_EN 1 BASIC SAFETY INSTRUCTIONS The core drill rig CDR 133 is exclusively designed for the drilling of construction products mainly within a construction site. Uses other than the manufacturer's instructions shall be considered as contravening the regulations. The manufacturer shall not be held responsible for any resulting damage.
VERS.2015.05.19 Kit CDR 133 + CDM 163_MAN_EN 1.2 Machine plate Important data can be found on the following plate located on the machine: Machine Model Machine Code Weight Year of production Serial number Machine type...
Immediately remove damaged or badly worn core bits, as they endanger the operator whilst rotating. Only fit NORTON diamond core bits to the machine! The use of other tools can damage the machine! Read the core bits’ specifications carefully to choose the adequate tool to your application.
As with all other NORTON products, the operator will immediately appreciate the attention given to detail and quality of materials used in construction. The machine and its component parts are assembled to high standards assuring long life and minimum maintenance.
VERS.2015.05.19 Kit CDR 133 + CDM 163_MAN_EN 2.4 Technical Data Max. drill bit diameter 130mm Movement 540mm Tilting Weight 8.9 kg Dimensions(Length x width x height) 375x250x870mm You can find the code number on the machine plate. If you bought a complete kit, your machine is composed of a column with combined base, a motor.
VERS.2015.05.19 Kit CDR 133 + CDM 163_MAN_EN 2.5 Statement regarding the vibration emission Declared value of vibration emission following EN 12096. Machine Measured value of vibration Uncertainty K Tool used Model / code emission at m/s Model / code KIT CDR 133 + CDM 163 <...
VERS.2015.05.19 Kit CDR 133 + CDM 163_MAN_EN 2.6 Statement regarding noise emission Declared value of noise emission following EN ISO 11201 and NF EN ISO 3744. Machine Sound Uncertainty K Sound power Uncertainty K Model / code Pressure level (Sound level (Sound power level Pressure level...
Retighten the screw so the motor cannot move in the collar. 3.2 Tool assembly Only NORTON core bit can be used with the CDR 133. All tools used must be selected with regard to their maximum permitted cutting speed for the machine’s maximum permitted rotation speed.
VERS.2015.05.19 Kit CDR 133 + CDM 163_MAN_EN This device works also as NVR (“No Volt Release”). It stops the electrical supply of the machine during a power cut. Therefore, when electricity returns, the machine will not start. You have to reengage the P.R.C.D.
VERS.2015.05.19 Kit CDR 133 + CDM 163_MAN_EN 4 TRANSPORT AND STORING Take the following measures in order to transport the CDR 133 securely. 4.1 Securing for transport Dismount the core bit, separate the motor from the rig, and the motor from electrical supply. 4.2 Transport procedure Use only surface transport to move the CDR 133.
Apply cooling water continuously whilst drilling and in good time! 5.2.2 Fixing the rig Only use NORTON tools to fix the rig. Always fix the rig before assembling the motor on the rig. When drilling overhead or horizontally into a wall, extra safety provision should be made with the...
Page 17
VERS.2015.05.19 Kit CDR 133 + CDM 163_MAN_EN Fixation with a dowel To fix the drill rig, you need a 15mm-dowel, a 30cm-long threaded rod, a washer and a wing nut. Bore a 15mm-diameter and 50mm-depth hole and clean it. ...
Page 18
VERS.2015.05.19 Kit CDR 133 + CDM 163_MAN_EN You are going through the steel rods for reinforced concrete. Follow these instructions: If possible, select a lower gear. Remember that you must firstly take the core bit out of the hole and switch the motor off in order to change from gear.
VERS.2015.05.19 Kit CDR 133 + CDM 163_MAN_EN 6 MAINTENANCE AND SERVICING To ensure a long-term quality from the cutting with the CDR 133, please follow the maintenance plan below: Whole machine Visual control (general aspect, watertightness) Clean Motor cooling fans Blow the dirt and dust Switch, cables and extension cables Inspect...
VERS.2015.05.19 Kit CDR 133 + CDM 163_MAN_EN 7 FAULTS: CAUSES AND CURES Fault-finding procedures Should any fault occur during the use of the machine, turn it off, and isolate it from the electric supply. Works dealing with the electric system or supply of the machine can only be done by a qualified electrician.
This machine has been manufactured by Saint-Gobain Abrasives S.A. 190, Bd. J.F. Kennedy L- 4930 BASCHARAGE Grand-Duché de Luxembourg. Tel. : 00352-50401-1 Fax : 00352- 50 16 33 http://www.construction.norton.eu e-mail: sales.nlx@saint-gobain.com...
Page 22
VERS.2015.05.19 Kit CDR 133 + CDM 163_MAN_EN Guarantee can be claimed and technical support obtained from your local distributor where machines, spare parts and consumables can be ordered as well:...