Related Manuals for Norton clipper CDR 353
Summary of Contents for Norton clipper CDR 353
- Page 1 Kit CDR 353 + NBM 351 OPERATING INSTRUCTIONS Translation of the original instructions...
- Page 2 VERS.2015.05.19 Kit CDR 353 + NBM 351_MAN_EN...
- Page 3 VERS.2015.05.19 Kit CDR 353 + NBM 351_MAN_EN Declaration of conformity The undersigned manufacturer: SAINT - GOBAIN ABRASIVES S.A. 190, BD. J. F. KENNEDY L-4930 BASCHARAGE Declares that this product: Kit CDR 353 + NBM 351 70184694707 « Drill Rigs »: Code : is in conformity with the following Directives : ...
- Page 4 VERS.2015.05.19 Kit CDR 353 + NBM 351_MAN_EN...
-
Page 5: Table Of Contents
VERS.2015.05.19 Kit CDR 353 + NBM 351_MAN_EN Kit CDR 353 + NBM 351 : OPERATING INSTRUCTIONS 1 BASIC SAFETY INSTRUCTIONS 1.1 Symbols 1.2 Machine plate 1.3 Safety instructions for particular operating phases 2 MACHINE DESCRIPTION 2.1 Short description 2.2 Purpose of use 2.3 Layout 2.4 Technical Data 2.5 Statement regarding the vibration emission... -
Page 6: Basic Safety Instructions
VERS.2015.05.19 Kit CDR 353 + NBM 351_MAN_EN BASIC SAFETY INSTRUCTIONS The core drill rig CDR 353 is exclusively designed for the drilling of construction products mainly within a Construction Site. Uses other than the manufacturer's instructions shall be considered as contravening the regulations. -
Page 7: Machine Plate
VERS.2015.05.19 Kit CDR 353 + NBM 351_MAN_EN Machine plate Important data can be found on the following plate located on the machine: Machine Model Machine Code Weight Year of production Serial number Machine type... -
Page 8: Safety Instructions For Particular Operating Phases
Immediately remove damaged or badly worn core bits, as they endanger the operator whilst rotating. Only fit NORTON diamond core bits to the machine! The use of other tools can damage the machine! Read the core bits’ specifications carefully to choose the adequate tool to your application. -
Page 9: Machine Description
As with all other NORTON products, the operator will immediately appreciate the attention given to detail and quality of materials used in construction. The machine and its component parts are assembled to high standards assuring long life and minimum maintenance. -
Page 10: Technical Data
VERS.2015.05.19 Kit CDR 353 + NBM 351_MAN_EN 2.4 Technical Data Max. drill bit diameter 350mm Movement 642mm Tilting 0 to 45° Weight of the rig 23.4 kg Dimensions (Length x width x 550x375x1080 mm height) You can find the code number on the machine plate. If you bought a complete kit, your machine is composed of a column with combined base, a motor and a motor assembling plate. -
Page 11: Statement Regarding The Vibration Emission
VERS.2015.05.19 Kit CDR 353 + NBM 351_MAN_EN Statement regarding the vibration emission Declared value of vibration emission following EN 12096. Machine Measured value of vibration Uncertainty K Tool used Model / code emission at m/s Model / code KIT CDR 353 + NBM 351 <... -
Page 12: Statement Regarding Noise Emission
VERS.2015.05.19 Kit CDR 353 + NBM 351_MAN_EN Statement regarding noise emission Declared value of noise emission following EN ISO 11201 and NF EN ISO 3744. Machine Sound Uncertainty K Sound power Uncertainty K Model / code Pressure level (Sound level (Sound power level Pressure level EN ISO 11201... -
Page 13: Assembly And Commissioning
Tighten the plate on the rig using the handle. 3.2 Tool assembly Only NORTON core bit can be used with the CDR 353. All tools used must be selected with regard to their maximum permitted cutting speed for the machine’s maximum permitted rotation speed. -
Page 14: Changing Motor Speed
VERS.2015.05.19 Kit CDR 353 + NBM 351_MAN_EN Security Device P.R.C.D. This circuit breaker must be connected to an electrical supply having the neutral connector and the earth connector separated. If there is a connection between these two connectors anywhere on the electrical net, the P.R.C.D. will automatically cut the circuit. Therefore, check with a qualified electrician, that this separation is correctly made on your electrical system. -
Page 15: Transport And Storing
VERS.2015.05.19 Kit CDR 353 + NBM 351_MAN_EN TRANSPORT AND STORING Take the following measures in order to transport the CDR 353 securely. 4.1 Securing for transport Dismount the core bit, separate the motor from the rig, and the motor from electrical supply. 4.2 Transport procedure Use only surface transport to move the CDR 353. -
Page 16: Operating The Machine
Apply cooling water continuously whilst drilling and in good time! 5.2.2 Fixing the rig Only use NORTON tools to fix the rig. Always fix the rig before assembling the motor on the rig. When drilling overhead or horizontally into a wall, only use dowels to fix the rig. Extra safety provision should be made with the use of a support sling to the drilling rig, in case of failure of anchor. - Page 17 VERS.2015.05.19 Kit CDR 353 + NBM 351_MAN_EN Fixation with a dowel To fix the drill rig, you need a 15mm-dowel, a 30cm-long threaded rod, a washer and a wing nut. Bore a 15mm-diameter and 50mm-depth hole and clean it. ...
- Page 18 VERS.2015.05.19 Kit CDR 353 + NBM 351_MAN_EN The core bit goes ahead very slowly. The force you have to make on the hand wheel increases. The water going out of the hole is clear and there are some metallic splints in it. You are going through the steel rods for reinforced concrete.
- Page 19 VERS.2015.05.19 Kit CDR 353 + NBM 351_MAN_EN 5.2.11 Drilling using an extension rod To make hole deeper than the tool length: Make the hole for the full depth of the bit. Take the bit out of the hole and switch the motor off. ...
-
Page 20: Maintenance And Servicing
VERS.2015.05.19 Kit CDR 353 + NBM 351_MAN_EN MAINTENANCE AND SERVICING To ensure a long-term quality from the cutting with the CDR 353, please follow the maintenance plan below: Whole machine Visual control (general aspect, watertightness) Clean Motor cooling fans Blow the dirt and dust Switch, cables and extension cables Inspect Water hoses and nozzles... -
Page 21: Faults: Causes And Cures
VERS.2015.05.19 Kit CDR 353 + NBM 351_MAN_EN FAULTS: CAUSES AND CURES Fault-finding procedures Should any fault occur during the use of the machine, turn it off, and isolate it from the electric supply. Works dealing with the electric system or supply of the machine can only be done by a qualified electrician. -
Page 22: Customer Service
Spare parts for the motor can be ordered with the manufacturer of the motor or with their dealer, which is often quicker and cheaper. This machine has been manufactured by Saint-Gobain Abrasives S.A. 190, Bd. J.F. Kennedy L- 4930 BASCHARAGE Grand-Duché de Luxembourg. Tel.: 00352-50401-1 Fax: 00352- 50 16 33 http://www.constructions.norton.eu e-mail: sales.nlx@saint-gobain.com... - Page 23 VERS.2015.05.19 Kit CDR 353 + NBM 351_MAN_EN Guarantee can be claimed and technical support obtained from your local distributor where machines, spare parts and consumables can be ordered as well:...
-
Page 24: Appendix
VERS.2015.05.19 Kit CDR 353 + NBM 351_MAN_EN APPENDIX Ideal rotation speed of the core bit in relation to the hole diameter... - Page 25 VERS.2015.05.19 Kit CDR 353 + NBM 351_MAN_EN...
- Page 26 VERS.2015.05.19 Kit CDR 353 + NBM 351_MAN_EN...
- Page 27 VERS.2015.05.19 Kit CDR 353 + NBM 351_MAN_EN...
- Page 28 VERS.2015.05.19 Kit CDR 353 + NBM 351_MAN_EN www.construction.norton.eu Saint-Gobain Abrasives 190, Bd. J. F. Kennedy L-4930 BASCHARAGE LUXEMBOURG Tel: ++352 50401-1 Fax: ++352 501633 e-mail: sales.nlx@saint-gobain.com...