Setting The Auto Measurement Interval; Recording Altitude Readings - Casio G-Shock GG-B100 Operation Manual

4.
Hold down (L) for at least two seconds to
set your current location's altitude as the
reference altitude.
This causes [DIFF CLR] to stop flashing
and displays the altitude at your current
location.
The second hand (Altitude Differential
●
Indicator) will indicate the difference
between the reference altitude and the
current altitude reading. At this time the
second hand should indicate ±0 m (±0
feet).
Altitude differential indicator
Current location altitude
5.
While comparing the difference between
the altitude you found on the map and the
altitude differential indicated by the
watch's second hand, advance towards
your destination.
When the altitude differential you found
●
on the map is the same as that indicated
by the second hand, it means you are
close to your destination.
Example: Altitude differential of -30 m (-98
feet) (-300 m (-984 feet))
Unit: m
100 50
Range:
±100 m (1000 m)
0
(±328 feet (3280 feet))
Altitude differential
indicator
−100 −50
Note
If the altitude differential is outside of
●
the specified range, the second hand
will indicate [OVER] or [UNDER].
If either of these is indicated while
using the ±100 m (328 feet)
measurement range, change the
range setting to ±1000 m (3280 feet).
The second hand will move to 9 o'clock
●
if a reading is outside the allowable
altitude measurement range (-700 m to
10,000 m (-2,300 to 32,800 feet)), or if
a reading error occurs.
Operation Guide 5594
Setting the Auto
Measurement Interval
You can select an auto measurement interval
of either five seconds or two minutes.
1.
Enter the Altimeter Mode.
Navigating Between Modes
l
2.
Hold down (D) for at least two seconds.
Release the button when [SET] starts to
flash and then disappears from the
display.
This displays the altitude for your current
location.
3.
Press (E).
This causes the auto measurement
interval to appear on the display.
4.
Press (A) to toggle the auto measurement
interval between [0'05] and [2'00].
[0'05]: Readings taken every second for
the first three minutes, and then every five
seconds for about the next one hour.
[2'00]: Readings taken every second for
the first three minutes, and then every two
minutes for about the next 12 hours.
5.
Press (D) to exit the setting screen.
Note
The watch will automatically return to
●
the Timekeeping Mode if you do not
perform any operation in the Altimeter
Mode for about one hour while [0'05] is
selected as the measurement interval
or about 12 hours while [2'00] is
selected.

Recording Altitude Readings

Use the procedure below to record altitude
measurements manually. Auto
measurements are also recorded
automatically.
Use the Altitude Record Recall Mode to
●
view or delete records.
Viewing Altitude Records
l
Recording Altitude Data Manually
●
1.
Enter the Timekeeping Mode or Altimeter
Mode.
Navigating Between Modes
l
2.
Hold down (A) for at least two seconds
until [REC] stops flashing on the display.
This records the current altitude, date,
and time.
There is enough memory to hold up to
●
14 altitude records.
Recording data when there are already
●
14 records in memory will automatically
delete the oldest record to make room
for the new one.
Note
If Mission Log is disabled, the watch
●
will automatically return to normal
Altitude Mode operation following
recording of altitude data.
If Mission Log is enabled and altitude
●
data is recorded, the watch will
connect with the phone and transfers
the data to it.
When a connection is established
between the watch and phone, [REC]
will change to [OK], and the second
hand will move from [R] to [C].
Recording Waypoints and Their
l
Altitudes (Mission Log)
[ERR] will appear on the display if
●
connection fails for some reason.
21