Eaton EWFFSC15 Quick Start Manual

EATON SMART HOME
Quick Start
Guide
Smart Fan Speed Control
EWFFSC15
Amazon, Alexa and all related logos are trademarks of Amazon.com,
Inc. or its affiliates. Google and Google Play are trademarks of Google
LLC. Wi-Fi CERTIFIED logo is a trademark of the Wi-Fi Alliance.
www.eaton.com
www.eaton.com/wiringdevices EIS-0279-E (REV. D)
Tools needed
Tools required for installation (not included) for the
Wi-Fi Smart Fan speed control (EWFFSC15):
Phillips-head Wire cutters
Screwdriver
Additional system requirements
A 2.4GHz Wi-Fi network with
high-speed internet
IOS 12.0 or later or Android 8.0 or later
mobile device. Note: Must be
connected to Wi-Fi and Bluetooth
A Brightlayer Home account set-up
through the Brightlayer Home App
Eaton's Wi-Fi Smart Devices
Eaton's broad selection of Wi-Fi Smart Devices offer reliability with unbeatable ease of setup.
Every device sets up quickly and easily with the Brightlayer Home App–no hubs or controllers
are necessary. You can add voice-control using any Alexa or Google device.
EWFD30 EWFSW15 EWFTRCR15
For more information on the complete Wi-Fi smart product portfolio please visit Eaton.com/smarthome
Set up and control Voice control
in the Brightlayer with Alexa and installation
Home App Hey Google
Prior to installation
Requires neutral for installation
WARNINGS AND CAUTIONS:
• Turn OFF circuit breaker or remove fuse(s) and test that power is
OFF before installation process
• Never wire any electrical device with power turned ON Wiring
fan speed control HOT may cause permanent
damage to fan speed control and void warranty
• If you are not sure about any part of these instructions, please
contact a licensed electrician
CAUTION
• Use only with 120V/AC 60Hz
• Do not exceed maximum rating of fan speed control as
indicated on the device
• Must be installed and used in accordance with all
national and local electrical codes
• If a bare copper or green ground connection is not
available in the wallbox, contact a licensed electrician
for installation
• Use only #14 or #12 copper wire rated for at least 75ºC with these
devices
DO NOT USE WITH ALUMINUM WIRE
IMPORTANT: Wi-Fi Smart Fan speed control (EWFFSC15) will
not work or will be damaged if wired incorrectly and warranty will
be voided. Refer to wiring instructions provided.
NOTE: The Wi-Fi Smart Fan speed control (EWFFSC15) is
wired directly to the ceiling fan fixture.
EWACD EWFFSC15
Easy No hub Set schedules,
required groups, and
scenes
Amazon, Alexa and all related logos are trademarks of Amazon.com, Inc.
or its affiliates. Google and Google Play are trademarks of Google LLC.
Wi-Fi CERTIFIED logo is a trademark of the Wi-Fi Alliance.
Single location installation
Neutral
Black Hot
120V
Load
Ceiling
Fan
Neutral
Can be wired with standard 3-way switch where traveler
wire exists for 3-way.
Your Wi-Fi Smart Fan Speed Control
Control your fans from anywhere with Eaton's Wi-Fi Smart
Fan Speed Control (EWFFSC15) which replaces standard
switches and features ON/OFF and DIM/BRIGHT control.
The Wi-Fi Smart Fan Speed Control (EWFFSC15) can be
remotely controlled using the Brightlayer Home App.
Neutral is required
Single pole & 3-way 3 Preset fan speeds
High, Medium, Low
Fan Speed Controller Rating - EWFFSC15
Load Type Single Gang
EWFFSC15
Ceiling fan 1.5A
Operation instructions
• Press ON button to turn fan ON at previously selected level
• Press the OFF button to turn the fan OFF
• The bottom LED indicates the fan speed controller
is turned ON
• When fan is OFF, press and hold the ON button for 2 seconds
until LED blinks green for full fan speed
FACTORY RESET: The fan speed controller can be reset which will
exclude the device from its network and restore all factory defaults.
• Turn ON the fan speed controller
• Press and hold the ON button for 30 seconds until the LED indicator
blinks red
• Release the button
• LED indicator will start flashing fast while it is being reset
• The LED indicator will then start blinking magenta at a normal rate
indicating the fan speed controller is not part of a Wi-Fi network
Scan for more advanced features
including adjusting the brightness level
of the LED indicators and additional
wiring configurations
For color change kit installation
instructions, see back page
Features
Eaton's Wi-Fi Smart Fan Speed Control has additional
features such as a selection of 3 fan speed controls
(High, Medium, Low).
Air gap
switch
ON button
Press to
speed up
LED speed
Status
level indicator
indicator
Status
indicator
OFF button
Press to
slow down
End User license agreement
Software included with the Eaton product is hereby
licensed to you, and Eaton retains for itself (or, if applica-
ble, its suppliers) all title and ownership to any software
delivered hereunder. Without Eaton's authorization, you shall
not copy, disclose or display the software, or otherwise make
it available to others, and shall not attempt any sale, transfer,
sublicense, reverse compilation or disassembly or redistribu-
tion of the software. By using the software, you agree to the
terms of Eaton's End User license agreement at:
https://www.eaton.com/WiFiSmartEULA
Contact us:
www.eaton.com/smarthome
Eaton.com/chat
TechSupport@eaton.com
Phone (Toll Free): 877-386-2273
Device support: Option 5 then Option 3
App support: Option 2 then Option 9
Fax (Toll Free): 800-329-3055