Diagnosis And Troubleshooting; System Error Messages - Endress+Hauser Smartec CLD132 Operating Instructions Manual

Smartec CLD132/134 PROFIBUS PA/DP
NAMUR Error Description
class no.
Failure E001 Memory error
Failure E002 Data error in EEPROM
Failure E003 Invalid configuration
Failure E007 Faulty transmitter
Failure E008 Sensor or sensor
connection faulty
Failure E010 Temperature sensor
defective
Failure E025 Limit value for airset
offset exceeded
Failure E036 Calibration range of
sensor exceeded
Failure E037 Below calibration
range of sensor
Failure E045 Calibration aborted
Failure E049 Installation factor
exceeded
Failure E050 Installation factor
undershot
Failure E055 Measuring range of
the main parameter
undershot
Failure E057 Measuring range of
the main parameter
exceeded
Failure E059 Temperature range
undershot
Failure E061 Temperature range
exceeded
Failure E067 Limit switch set point
exceeded
Failure E077 Temperature not
within the α-value
table
Failure E078 Temperature not
within the
concentration table
Failure E079 Conductivity not
within the
concentration table
Funct. E101 Service function active
check
Endress+Hauser
9

Diagnosis and troubleshooting

9.1

System error messages

The DIAGNOSIS and DIAGNOSIS_EXTENSION parameters are generated from the device-
specific errors.
DIAGNOSIS
01 00 00 80 - DIA_HW_ELECTR
10 00 00 80 - DIA_MEM_CHKSUM
00 04 00 80 - DIA_CONF_INVAL
20 00 00 80 - DIA_MEASUREMENT
20 00 00 80 - DIA_MEASUREMENT
20 00 00 80 - DIA_MEASUREMENT
20 00 00 80 - DIA_MEASUREMENT
20 00 00 80 - DIA_MEASUREMENT
20 00 00 80 - DIA_MEASUREMENT
20 00 00 80 - DIA_MEASUREMENT
20 00 00 80 - DIA_MEASUREMENT
00 20 00 80 - DIA_MAINTENANCE
20 00 00 80 - DIA_MEASUREMENT
20 00 00 80 - DIA_MEASUREMENT
20 00 00 80 - DIA_MEASUREMENT
20 00 00 80 - DIA_MEASUREMENT
00 20 00 80 - DIA_MAINTENANCE
00 04 00 80 - DIA_CONF_INVAL
00 04 00 80 - DIA_CONF_INVAL
0 04 00 80 - DIA_CONF_INVAL
Diagnosis and troubleshooting
DIAGNOSIS_ Measured value status
EXTENSIO
Quality
01 00 00 00 00 00 BAD
02 00 00 00 00 00 BAD
04 00 00 00 00 00 BAD
08 00 00 00 00 00 BAD
10 00 00 00 00 00 BAD
20 00 00 00 00 00 BAD
40 00 00 00 00 00 BAD
80 00 00 00 00 00 BAD
00 01 00 00 00 00 BAD
00 02 00 00 00 00 BAD
00 04 00 00 00 00 BAD
00 08 00 00 00 00 BAD
00 10 00 00 00 00 UNCERT
AIN
00 20 00 00 00 00 UNCERT
AIN
00 40 00 00 00 00 UNCERT
AIN
00 80 00 00 00 00 UNCERT
AIN
00 00 00 04 00 00 UNCERT
AIN
00 00 01 00 00 00 BAD
00 00 02 00 00 00 BAD
00 00 04 00 00 00 BAD
-
1)
Sub-status Hex
device failure 0C
device failure 0C
device failure 0C
device failure 0C
sensor failure 10
sensor failure 10
configuration 04
error
configuration 04
error
configuration 04
error
configuration 04
error
configuration 04
error
configuration 5C
error
sensor 50
conversion not
accurate
sensor 50
conversion not
accurate
sensor 50
conversion not
accurate
sensor 50
conversion not
accurate
non-specific 40
configuration 04
error
configuration 04
error
configuration 04
error
-
35