1. Manuals
  2. Brands
  3. Cal-Royal Manuals
  4. Door locks
  5. PL2S-2
  6. User manual

Cal-Royal PL2S-2 - Touchpad Electronic Deadbolt Lock Manual

Also See for PL2S-2:

Advertisement

Table of Contents
Contents
Cal-Royal PL2S-2 - Touchpad Electronic Deadbolt Lock Manual

Operational Interface

Operational Interface

  1. Programming Button
    Programming button is for setting function.
  2. Lock Buttons
    Lock Button is for lock and unlock function.
  3. Cylinder
    To lock/unlock the lockset by key from outside.
  4. Washer
    Prevents water from permeating into lockset.
  5. Battery Lid
    Slide the lid to change the batteries.
  6. Battery Holder
    Four AA (1.5 V) alkaline batteries.
  7. R Button (Reset)
    Restore default settings.
  8. Turn-piece
    To lock/unlock the lockset from inside.

Operating Instructions

Keep the door open while programming to avoid being locked out accidentally. The lock contains one factory-preset user code but can be programmed to store up to a total of thirty additional unique user codes.

Codes can be added and deleted at any time. For first-time programming, use factory default programming code. It's recommended to change the default programming code and default user code right after you install the lock.

Every programming step should be done within 6 seconds.

Operation Indicator Sounds and Lights

Sounds Lights Meaning
1 Beep Successful Operation
2 Long Beeps Successful Programming
3 Beeps Operation Error
5 Beeps Code Input Error; System Shuts Down
10 Rapid Beeps Low Battery Power
3 Long Beeps Default Setting Restored
Lock button flashes slowly In Programming Mode

Default programming code (PC): 0000
Default user code (UC): 1234
Your new programming code (PC) ____________
Your new user code (UC) ___________________
The same programming code and user code cannot be accepted.
The lock will cease operation if unauthorized codes are entered over 5 times.
The system will unfreeze after 45 seconds.

  1. Door Handing Identification Process
    The lock needs to learn if your door is a right-handed or left-handed.
    warningDO THIS FIRST
    Operating Instructions - Step 1
  2. Change Programming Code
    Operating Instructions - Step 2
  3. Add New User Code
    Operating Instructions - Step 3
    Note: Up to 30 sets of user codes can be saved. User codes should be 4–10 digits in length.
  4. Delete an Existing User Code
    Operating Instructions - Step 4
  5. Delete All User Codes at Once
    Operating Instructions - Step 5
    Note: Auto-locking and keypad locking functions will be invalid when user codes are deleted. The lock can only be operated by key during that time.
  6. Toggle Auto-Lock On/Off
    Operating Instructions - Step 6
    Note: The preset delay-time is 30 seconds, you can change the time by following instructions #7.
    Repeat the steps in #6 to cancel the auto-locking function.
  7. Set Auto-Lock Time Delay
    Operating Instructions - Step 7
  8. Enable/Disable All User Codes
    Operating Instructions - Step 8
    Note: Auto-locking and keypad locking functions will be invalid when user codes are disabled. The lock can only be operated by key during the time. Repeat the steps to enable the user codes again.
  9. Create a One-Time User Code 4–10 Digits Long
    Operating Instructions - Step 9
    Note: The one-time user code will automatically cancel after it is used one time.
  10. Restore Default Settings

    Press
    Note: Press the button for more than 5 seconds; the programming is reset back to the original factory codes once you hear 3 long beeps. After restoring default settings, you must run the door handing identifying process (#1) again before programming any other functions.

Troubleshooting

PROBLEM POSSIBLE CAUSE CORRECTIVE ACTION
After installing the lockset and batteries, the door can't be locked and three short beeps are emitted when you press the lock button. The door-handing identification process isn't yet complete. Refer to step1.
You've installed the lockset and batteries, but you still get no response when you press any button. Batteries were installed incorrectly and cable connect incorrectly. Check to see if the battery polarities have been reversed or if the battery is dead. If so, re-install or change the battery. If not, please check to see if the cable is properly connected.
When you are in the door-handing identifying process, you get the red light flashing three times, and three short beeps. Wrong door-handing or change of the door-handing in the memory. Press the R button to restore the system to factory default setting and re-execute door-handing identifying process ( Refer to step 1)
Although you succeeded in the first execution of the door-handing identifying process, the latch still doesn't work. (i.e. You can feel the motor attempting to run.) Low battery. Replace with new alkaline batteries.
The door can be locked normally, but when you try to unlock it, you hear three short beeps and the lock won't unlock when you enter the user code and press the lock button. The functioning of the micro-switch is abnormal. Call our customer service department.
While the door is locked, you hear the latch bolt coming out when you press the to lock the door; however, three short beeps are emitted. Conversely, while the door is open, no beeps are emitted when locking the latch bolt.
  1. The depth of the latch bolt hole is insufficient.
  2. The latch bolt is not aimed at the opening of the strike.
  1. Dig the latch bolt hole for the strike deeper. The minimum depth is 1" (2.5 cm).
  2. Adjust the strike to the appropriate position.

Documents / Resources

Download manual

Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.

Download Cal-Royal PL2S-2 - Touchpad Electronic Deadbolt Lock Manual

Advertisement

Need help?

Need help?

Do you have a question about the PL2S-2 and is the answer not in the manual?

Questions and answers

Related Manuals for Cal-Royal PL2S-2

Save Article as PDF

Table of Contents