Advertisement
Canopy
Screw
Canopy
Screw
Setscrew
Push the two canopy halves
Tighten the setcrew.
from the kit together around
the hanging system. Make sure
that the receiver is tucked inside.
Partially install the canopy screws
from the kit into the screw holes.
Slide the canopy up close to the
ceiling. Tighten all four screws.
Safe-Exit
Troubleshooting
The Safe-Exit Program gives
Fan will not start
you about thirty seconds of light
• Make sure the power is on at the
when you turn the lights off to
circuit breaker and the wall switch.
exit the room before the lights
• Make sure the battery is working.
go out. To use Safe-Exit:
• Make sure that the transmitter and
receiver are paired.
• Press the fan OFF button for at
• Check wire connections inside of
least three seconds to initiate the
the canopy.
Safe-Exit Mode.
Remote control of fan is erratic
• The lights will flash for visual
• Make sure the battery is installed
confirmation.
correctly.
• The lights will stay on 50%
• Install a fresh battery.
brightness for 15 seconds and
then begin to dim. After a total
Transmitter only works when held
of 30 seconds, the lights will be
at close range
completely off.
• Change battery.
Note: For CFL lighting, the lights
Lights do not dim
will stay on 100% brightness
for 30 seconds. After a total of
• Check to see if a CFL bulb is
30 seconds, the lights will be
installed. The control has a feature
completely off.
that automatically detects CFL bulbs
and turns off dimming if a CFL bulb
is installed.
CFL bulbs flicker
• Turn the light switch off and back
on. Within three minutes, hold down
the Fan Off button while pressing
the Light Off button twice. If the
problem is not corrected, repeat the
process up to three times.
Battery
Door
Phillips
ON
ON
Head
Screw
Installing or changing the
IMPORTANT
battery
To access the battery
Use the pull-chain switch
compartment remove the small
on the fan to set the
Phillips head screw that secures
fan speed to the HIGH
the battery door to the transmitter
position before operation.
assembly. Replace with a CR2032
battery when necessary. The
battery should be installed with
the positive (+) side up.
HUNTER FAN COMPANY CONTROL LIMITED WARRANTY
The Hunter Fan Company makes the following limited warranty to the original purchaser
of the Control ("Control"): Your Control is warranted to be free from defects in material and
workmanship for a period of one year from the date of sale. If the Control malfunctions or fails
within the warranty period due to a defect in material or workmanship we will replace it free
of charge. IF THE ORIGINAL PURCHASER CEASES TO OWN THE CONTROL, THIS WARRANTY
AND ANY IMPLIED WARRANTY, INCLUDING BUT NOT LIMITED TO ANY IMPLIED WARRANTY OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, ARE VOIDED. THIS WARRANTY
IS IN LIEU OF ALL OTHER EXPRESS WARRANTIES. THE DURATION OF ANY IMPLIED WARRANTY,
INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR
FITNESS FOR A PARTICULAR PURPOSE, IN RESPECT TO ANY CONTROL, IS EXPRESSLY LIMITED
TO THE PERIOD OF THE EXPRESS WARRANTY SET FORTH ABOVE FOR SUCH CONTROL. This
warranty excludes malfunctions or failures which were caused by repairs by persons not
authorized by us, mishandling, improper installation, modifications, or damage to the Control
while in your possession, or unreasonable use. This warranty does not apply to batteries or
to deterioration or damage to the product caused by the use of faulty batteries. To obtain a
replacement, return your Control postage prepaid along with proof of purchase to Hunter
Fan Company Service Department at 7130 Goodlett Farms Pkwy., Memphis, TN 38016. IN
NO EVENT SHALL HUNTER FAN COMPANY BE LIABLE FOR CONSEQUENTIAL OR INCIDENTAL
DAMAGES. SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED
WARRANTY LASTS OR THE EXCLUSION OR LIMITATIONS OF INCIDENTAL OR CONSEQUENTIAL
DAMAGES SO THE ABOVE LIMITATIONS OR EXCLUSIONS MAY NOT APPLY TO YOU. THIS
WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS AND YOU MAY ALSO HAVE OTHER RIGHTS
WHICH VARY FROM STATE TO STATE.
If you have problems installing or operating your fan, do not return this
product to the dealer. Call our Consumer Affairs Hotline.
1-888-830-1326
M0093-01 • 06/17/20 • © 2020 Hunter Fan Company
Pairing
Cradle
High
Fan Off
To install the transmitter cradle,
Note: The remote must be paired
remove the two screws holding
before the fan will operate.
your switch cover plate. Do not
Within 3 minutes of restoring
remove the cover plate. Orient
power to the fan, press both
the cradle by lining up the two
the Fan Off button and the High
mounting holes with those on the
button for at least 4 seconds. Your
cover plate. Insert and tighten the
fan will turn on low to indicate
screws. Do not over tighten.
successful syncing. If it does not,
turn off power to your fan, wait
1 minute then try again. If using
the transmitter with multiple fans,
repeat this process for each fan.
This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation.
This device complies with RSS-210 of Industry Canada. Operation is subject to
the following two conditions: (1) this device may not cause interference, and (2)
this device must accept any interference, including interference that may cause
undesired operation of the device.
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However there is no
guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following
measures: Reorient or relocate the receiving antenna, Increase the separation
between the equipment and receiver, Connect the equipment into an outlet on
a circuit different from that to which the receiver is connected. Consult the
dealer or an experienced radio/TV technician for help. Note: Any changes or
modifications to the transmitter or receiver not expressly approved by Hunter
Fan Company may void one's authority to operate this remote control.
www.HunterFan.com
1.888.830.1326
If your fan has a
Operation
light kit:
High
Medium
Low
Fan Off
The Fan Off button only turns the
Quickly press the Light button
fan off. To turn the fan on, press
to turnthe lights off and on. Hold
one of the fan speed buttons.
the Light button to raise and dim
the light level.
ooo
High
oo
Medium
o
Low
Read and Save These Instructions
This product conforms to UL Standard 507.
WARNINGS
Light
Advertisement
