Hunter 85095 Instruction Supplement

®
Transmitter Model: 85095
Transmitter Battery: 12 V, Type 23A, MN-21 or equivalent
Receiver Model: 85069
Ratings: 120 VAC, 60 Hz,1.0 Amp Fan
Receiver Weight: 8 oz.
240 Watts incandescent light
Read and Save these Instructions
Caution: Risk of Electrical Shock!
All wiring must be performed in accordance with national and local electri-
cal codes. If you are unfamiliar with the wiring codes, you should use a
qualified electrician.
To avoid overheating and possible damage to other equipment, do not
install to control a receptacle, fluorescent light fixture, motor operated ap-
pliance, or transformer-supplied appliance. Use only to control one paddle-
blade ceiling fan and incandescent light fixture.
This device complies with part 15 of the FCC rules. Changes or modifica-
tions not expressly approved by Hunter Fan Company could void your au-
thority to operate this equipment!
Operation Is Subject To The Following Two Conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including interfer-
ence that may cause undesired operation.
Note: Any changes or modifications to the transmitter or receiver not ex-
pressly approved by Hunter Fan Company may void one's authority to oper-
ate this remote control.
Your fan is equipped to be operated by remote control. A receiver device is
mounted inside the fan switch housing. A hand-held transmitter is packed
in the fan box. The transmitter requires a 12-volt battery (included). The
operating range is 15-30 feet.
Setting The Code
When two or more fans are located near each other, you may desire to have
each of them set to a different code, so that the operation of one fan will
not affect another. This is accomplished by changing the position of any
one or more of a group of 3 jumpers grouped together in the transmitter.
The receiver located in the switch housing has the same set of 3 jumpers
which must also be changed to match the transmitter settings.
These jumpers are very small and can best be operated by using a small pair
of pliers or tweezers.
In the transmitter, the jumpers are readily accessible from the battery com-
partment. The switches in the receiver are located at the bottom of the
receiver device in the switch housing. See Figures 1 and 2.
To set the jumpers in the receiver, remove the receiver from the switch housing
and set the jumpers in the same positions as the jumpers in the transmitter.
See Figure 2.
Replace the receiver, making sure the mounting holes at the top of the
switch housing line up with the matching slots in the top of the receiver.
Figure 1 - Transmitter Jumper Switches
Form # 41476-01 Rev. 2-23-2001
Downloaded from www.Manualslib.com
Hunter Fan Company
Integrated Remote Control
Instruction Supplement
Jumper
Switch
Transmitter
Back
manuals search engine
Receiver
Bottom
Lower Switch Housing
Figure 2 - Receiver Jumper Switches
Assembling The Switch Housing
Assemble the lower switch housing to the upper housing. See Figure 3.
First insert the plug from the upper housing into the plug receptacle in the
receiver module.
NOTE: The plug is polarized and will only go together one way. Make sure
you have correctly aligned plug and receptacle.
Next, line up the lower switch housing with the upper housing and as-
semble together with the (3) screws and lockwashers provided. See Figure
3.
Assembly
Screw
Plug Connector
Figure 3 - Lower Switch Housing Assembly
If the two pieces are difficult to assemble, check the alignment of the (3)
slots in the top of the receiver module and the mounting holes in the lower
switch housing. They should align together.
Tighten the (3) assembly screws.
CAUTION: Make sure the screws are snug, otherwise the assembly could
separate during operation.
Mounting the Remote Holder
A holder is supplied with the transmitter which can be mounted to a exist-
ing toggle switch wall plate. The holder will help prevent misplacement of
your transmitter by providing a permanent receptacle. See Figure 4.
If desired, the holder can be mounted to a convenient location on a wall.
Figure 4 - Remote Holder Assembly
Jumper
Switch
Pull receiver out
of switch housing.
Upper Switch
Housing
Lower Switch
Housing