Advertisement
Installation
OFF
Before installing the
Remove the canopy. If uncertain
Universal Remote Control
how to remove it, reference the fan's
Receiver, use the pull chains
owner's manual. With wiring exposed,
to set the fan speed to HIGH
it may be helpful to note existing wire
and the light to ON. Be
connections or take a digital photo for
sure power is OFF before
reference. Remove the wire connectors
proceeding with installation.
that connect the wires from the outlet
box to the fan, leaving the grounding
wires connected.
Wiring
blue (light out)
black (fan out)
white (common out)
CONNECT WIRES FROM RECEIVER TO FAN -Using the blue wire connectors connect the white wire from the receiver
(marked "common out") to the white wire from fan. Connect the black wire from the receiver (marked "fan out") to the
black wire from the fan. Connect the blue wire from the receiver (marked "light out") to the blue wire (or possibly black
with white stripe) from the fan.
If you're uncertain about wire colors or connections, please contact a qualified electrician.
Turn the splices upward and push them carefully back through the hanger bracket
into the outlet box. Spread the wires apart, with the grounded wires on one side of
the outlet box and the ungrounded wires on the other side of the outlet box.
Universal Ceiling
Fan Remote Control
Model #99110
Receiver
OR
Canopy
Choose the hanging system that most closely resembles the one used by your fan and install the receiver and wire as directed.
Note: Some fans may have considerable excess lead wire. For easier canopy installation, cut the excess wire, leaving a minimum of 8" remaining. Re-strip the fan lead wires 1/2" . Place remaining excess
wire into the ceiling electrical box. The bracket and fan must remain properly grounded.
You may have installation issues if the fan is installed on an angled ceiling.
blue
black
white
M0032-01 • 10/22/12 • © Hunter Fan Company
Receiver
Ceiling
Plate
OR
Receiver
Canopy
Canopy
black (live in)
black (ungrounded)
white (neutral in)
white (grounded)
CONNECT WIRES FROM RECEIVER TO WIRES FROM OUTLET BOX - Using an orange wire connector connect
the black wire (ungrounded) from the ceiling to the black wire from the receiver (marked "live in"). Connect
the white wire (grounded) from the ceiling to the white wire from the receiver (marked "neutral in").
AFTER ALL WIRES ARE CONNECTED and secured with wire connectors, re-install the canopy.
To avoid possible electrical shock, before installing or servicing your fan, disconnect
the power by turning off the circuit breakers to the outlet box and associated wall switch
location. If you cannot lock the circuit breakers in the off position, securely fasten a
prominent warning device, such as a tag, to the service panel.
www.HunterFan.com
1.888.830.1326
For low pro le fans, the receiver should
be secured to the hanger bracket with
a cable tie.
Cable Tie
Ceiling
Bracket
OR
Receiver
Fan Body
Advertisement
Table of Contents
Related Manuals for Hunter 99110
Summary of Contents for Hunter 99110
- Page 1 If you cannot lock the circuit breakers in the off position, securely fasten a the outlet box and the ungrounded wires on the other side of the outlet box. prominent warning device, such as a tag, to the service panel. M0032-01 • 10/22/12 • © Hunter Fan Company...
- Page 2 • Make sure the power is on at the This product conforms to UL Standard 507. The Hunter Fan Company makes the following limited warranty to the original purchaser light when you turn the lights circuit breaker and the wall switch.
Need help?
Do you have a question about the 99110 and is the answer not in the manual?
Questions and answers
How do you pair the remote for the 99110 model
To pair the remote for the Hunter 99110 model, follow these steps:
1. Install a fresh battery in the remote with the positive (+) side up.
2. Turn off the circuit breaker or wall switch to the fan.
3. Turn the power back on.
4. Press and hold the pairing button on the remote.
5. The fan will alternate speeds, indicating that the pairing process is complete.
6. If using the remote with multiple fans, repeat the process for each fan.
This answer is automatically generated
@Mr. Anderson there is no pairing button
i just put a new battery in my hunter ceiling **** and it stiill doesn't work
Your Hunter ceiling fan with part number 99110 may not be working after replacing the battery due to the following reasons:
1. Incorrect Battery Installation – Ensure the battery is installed correctly with the correct polarity.
2. Dead or Faulty Battery – Try installing a fresh battery.
3. Remote Control Pairing Issue – The remote may need to be re-paired with the fan. Hold the fan off button for three seconds, then try holding the light button to activate the dim setting.
4. Interference or Signal Disruption – Other electronic devices may be causing interference.
5. Faulty Receiver or Wiring Issue – If the fan still does not respond, check the receiver and wiring connections.
If the issue persists, consider consulting a qualified electrician.
This answer is automatically generated
how to program 99110 remote
The provided context does not contain detailed programming instructions for the Hunter remote model 99110. However, it mentions that the pairing procedure is not included in the instructions that come with the remote and can be found in a hidden PDF on Hunter's website. Additionally, users have reported difficulty in pairing multiple remotes with receivers. For accurate programming steps, refer to the official Hunter documentation or manual.
This answer is automatically generated
I have remote #99110. Its not doing its job so I have been trying to open the remote to check and change batteries. It's IMPOSSIBLE to get it opened. I'm a senior so I asked some younger folks to help, but non one can get the back thing open to check the battery. Can I get another remote and how???