Table of Contents
Advertisement
Quick Links
TMG-1500PML
PRODUCT MANUAL
v2023.06.18
1500-LB PORTABLE
MOTORCYCLE/ATV LIFT
1,5
Please read and understand the product manual completely before assembly
Check against the parts list to make sure all parts are received
Wear proper safety goggles or other protective gears while in assembly
Do not return the product to dealer. They are not equipped to handle your requests.
Missing parts or questions on assembly?
Please call: 1-877-761-2819 or email: cs@tmgindustrial.com
Advertisement
Table of Contents
Related Manuals for TMG TMG-1500PML
Summary of Contents for TMG TMG-1500PML
- Page 1 TMG-1500PML PRODUCT MANUAL v2023.06.18 1500-LB PORTABLE MOTORCYCLE/ATV LIFT Please read and understand the product manual completely before assembly Check against the parts list to make sure all parts are received Wear proper safety goggles or other protective gears while in assembly Do not return the product to dealer.
-
Page 2: Important Notice
IMPORTANT NOTICE Do not attempt to install this lift if you have never been trained on basic motorcycle lift installation procedures. Never attempt to lift components without proper lifting tools such as a forklift or crane. Stay clear of any moving parts that can fall and cause injury. -
Page 3: Installer / Operator Protective Equipment
INSTALLER / OPERATOR PLEASE READ AND FULLY UNDERSTAND. BY PROCEEDING YOU AGREE TO THE FOLLOWING. I have visually inspected the site where the lift is to be installed and verified the concrete to be in good condition and free of cracks or other defects. I under- stand that installing a lift on cracked or defective concrete could cause lift failure resulting in personal injury or death. -
Page 4: Important Safety Instructions
IMPORTANT SAFETY INSTRUCTIONS IMPORTANT SAFETY INSTRUCTIONS Read these safety instructions entirely. Do not attempt to install this lift if you have never been trained on basic motorcycle lift installation procedures. Never attempt to lift components without proper lifting tools such as forklifts or equipment, basic safety cranes. -
Page 5: Tools Required
TOOLS REQUIRED Open-End Wrench Set: Metric Socket And Ratchet Set: Metric IMPORTANT NOTICE THESE INSTRUCTIONS MUST BE FOLLOWED TO ENSURE PROPER INSTALLATION AND OPERATION OF YOUR LIFT. FAILURE TO COMPLY WITH THESE INSTRUCTIONS CAN RESULT IN SERIOUS BODILY HARM AND VOID PRODUCT WARRANTY. MANUFACTURER WILL ASSUME NO LIABILITY FOR LOSS OR DAMAGE OF ANY KIND, EXPRESSED OR IMPLIED, RESULTING FROM IMPROPER INSTALLATION OR USE OF THIS PRODUCT. - Page 6 TO LOWER LIFT: 1. Raise the lift slightly and lift the safety latch and lower to next position or to the floor. VISUALLY CONFIRM THAT SAFETY LOCK IS ENGAGED BEFORE ENTERING WORK AREA. REMAIN CLEAR OF ELEVATED LIFT UNLESS VISUAL CONFIRMATION IS MADE THAT SAFETY LOCK IS FULLY ENGAGED AND THE LIFT IS LOWERED ONTO THE SAFETY LOCK, REFER TO INSTALLATION / OPERATION MANUAL FOR PROPER SAFETY LOCK PROCEDURES AND / OR FURTHER INSTRUCTION.
-
Page 7: Locking Mechanism
LOCKING MECHANISM 1. The lock release mechanism is located on the left side of the lift if facing it as you would push your bike onto the lift. 2. There are two positions for the lock release lever. The upper position is the unlocked position and the lower position is the locked position. - Page 8 Safe Lift Operation Continued All maintenance and repairs of the lift should be completed by following the manufacturer’s requirements. Lift repair parts should meet or exceed OEM specifications. Repairs should only be completed by a qualified lift technician. The vehicle manufacturer’s recommendations should be used for spotting and lifting the vehicle. LIFT OPERATION SAFETY It is important that you know the load limit.
-
Page 9: Main Parts Breakdown
MAIN PARTS BREAKDOWN MAIN PARTS PARTS LIST PART NO. DESCRIPTION PART NO. DESCRIPTION Deck plate Roll pin 16x70 Adjustable vise arm M16 retainer ring Tire stop M16X80mm bolt Stationary vise arm M16 nylon lock nut Rubber plate Center axis Ø16 X620 Side extensions ( Right &... - Page 10 CYLINDER BREAKDOWN CYLINDER PARTS LIST PART NO. DESCRIPTION PART NO. DESCRIPTION Cylinder end cap M45x25 Steel ball Ø6 Flow regulator valve Piston Ø34x343 Y-ring 42x32x6 Hydraulic cylinder tube Flow regulator valve connect Compound gasket Ø14 Piston head Exhaust filter mesh...
-
Page 11: Pump Breakdown
PUMP BREAKDOWN B42 B41 B35 B36... -
Page 12: Pump Parts List
PUMP PARTS LIST PART NO. DESCRIPTION PART NO. DESCRIPTION Plunger pump body Cylinder head spring Ø9.5x16 Overflow washer Ø10 Back cover Overflow valve body Pump cover seal washer Overflow one-way valve Reservoir cover Overflow ball holder Oil outlet O-ring Ø30x3.3 Overflow spring Ø12x8 Air vent O-ring Ø18x3.3 Adjust plug...
Need help?
Do you have a question about the TMG-1500PML and is the answer not in the manual?
Questions and answers