Advertisement
Quick Links
Utilizing field and introduction
PD-MV1005-Z is a moving object sensor that can detect range of 360°and it's working frequency is 5.8G.The
advantage of this product is stable working state (stable working temperature: -15°C~+70°C), PD-MV1005-Z
adopts a microwave sensor(high-frequency output<0.2mW),so that it is safe and performs better than infrared
sensor.
It uses the MCU to accurately calculate the switch information, and accurately controls the relay to be turned on at the
zero point of the sine wave, so that each load is turned on. At the zero point of the sine wave, the inrush current problem
caused by the conventional control mode when the sine wave high voltage is turned on is avoided, especially the large
current damage relay generated by the large-capacity capacitor under the impact of the high voltage under the load.Due
to the diversification of current electrical loads, especially LED lamps, energy-saving lamps, and fluorescent lamps all
have capacitors with different capacitances. This is a disaster for relays. Sometimes a 50W LED lamp can generate
surge currents of 80 to 120A. The 10A ordinary relay can only withstand 3 times of the inrush current, and it is likely that
the relay will be broken in a few days or several times. This is why the conventional sensor on the market has a short life
and a small load current.
In order to overcome this problem, this product adopts advanced digital precision calculation to turn on the load when
the sine wave is at zero potential, thus solving the load surge current problem, greatly enhancing the load capacity and
prolonging the service life of the product. The latest control method of mass production sensor technology can easily
control any load. It is a medium and high-end product. Although the cost is increased compared with the conventional
version, the reliability and life of the product are greatly increased. This product is equal to choosing peace of mind, and
choosing safety.
Note:
the high-frequency output of this sensor is
<0.2mW- that is just one 5000 of the transmission
power of a mobile phone or the output of a
microwave oven.
Specifications
Power source: 220-240VAC 50/60Hz
Transmission power: <0.2mW
Rated load:1200W. any load
Installation sit: indoors, ceiling mounting
Detection angle: 360°
Microwave Sensor
th
PD-MV1005-Z instruction
42.00mm
Transmission power<0.2mW
Detection range（22℃）: 2-10m(radii.) (adjustable)
Time setting: 8sec to 12min ( (adjustable)
Light-control: 2~2000LUX (adjustable)
Working temperature: -15°C~+70°C
HF system: 5.8GHz CW Electric wave,ISM band
42.00mm
Advertisement
Related Manuals for pdlux PD-MV1005-Z
Summary of Contents for pdlux PD-MV1005-Z
- Page 1 42.00mm Utilizing field and introduction PD-MV1005-Z is a moving object sensor that can detect range of 360°and it’s working frequency is 5.8G.The advantage of this product is stable working state (stable working temperature: -15°C~+70°C), PD-MV1005-Z adopts a microwave sensor(high-frequency output<0.2mW),so that it is safe and performs better than infrared sensor.
- Page 2 Utilized in ceiling light This product can be utilized in more fields than the above examples. You can also install a PD-MV1005-Z in the ceiling directly to control an aisle. There is no problem. Warning! Non-metal material The product can not work normally if there is when the sensor is installed inside the ceiling floor, metal material behind the Installed place.
- Page 3 TIME If you want PD-MV1005-Z to detect small zone, you can just adjust the sense knob SENS to the range that you need (You may need to adjust some times untill you think it is suitable).If you want that the light can be turned...
- Page 4 If you want use PD-MV1005-Z as a single, you can also order the shell which is especially manufactured for the product to be installed in, or you can select the product PD-MV1005-Z-A directly. The protection grade of PD-MV1005-Z-A is IP55, so PD-MV1005-Z-A is better than PD-MV1005-Z with the higher water proof quality.