Yeedi K700, K701G - Robot Vacuum Manual

Also See for K700:

Instruction manual (78 pages)

Instruction manual (150 pages)

Table of Contents

Contents

1 Package Contents
- 1.1 Package Contents
- 1.2 Product Diagram
2 Operating and Programming
3 Maintenance
4 Indicator Light
5 Troubleshooting
6 Technical Specifications
7 Documents / Resources
- 7.1 Download manual

Yeedi K700, K701G - Robot Vacuum Manual

Package Contents

Note: Figures and illustrations are for reference only and may differ from actual product appearance.
Product design and specifications are subject to changes without notice.

Product Diagram

Robot

Bottom View

Docking Station

Remote Control

Advanced Mopping System

Operating and Programming

Notes Before Cleaning

Do not use The robot on wet surfaces or surfaces with standing water.

Before using the product on a rug with tasseled edges, please fold the rug edges under.

It may be necessary to place a physical barrier at the edge of a drop to stop the unit from falling over the edge.

Tidy up the area to be cleaned by putting furniture, such as chairs, in their proper place.

Remove power cords and small objects from the floor that the robot could be obstructed by.

Preparation

Remove Protective Strip
Docking Station Placement
Install Side Brushes
Power ON
Charge The robot

Note: When the robot completes the cleaning cycle or when battery power gets low, The robot automatically returns to the Docking Station to recharge itself.

Selecting Cleaning Mode

AUTO Cleaning Mode
A Programmed Cleaning Pattern (optimized for hard floors) will be selected by default.
Return to Docking Station
Edge Cleaning Mode
Spot Cleaning Mode (Less than 3 minutes)

Switch vacuum power

Pause, Wake Up, Power Off

Pause

Note: The robot's Control Panel stops glowing after the robot is paused for a few minutes. Press the AUTO Mode Button on the robot to wake up the robot.
Wake Up
Power OFF

Note: When the robot is not working, it is recommended to keep it switched ON and charging.

Optional Mopping System

Note: Empty the Reservoir and remove the Cleaning Cloth Plate before cleaning on carpet.
When using the mopping system, fold area rug edges under themselves so The robot will avoid the rug.
Be sure to use only water, and do not put washer fluid or any other cleaning solution in the Reservoir.

Optional Mopping System Operation

Note: After The robot finishes mopping, empty any remaining water from the Reservoir.

Maintenance

Before performing cleaning and maintenance tasks on The robot, turn the robot OFF and unplug the Charging Dock.

Optional Mopping System

Optional Mopping System Maintenance

Before performing cleaning and maintenance tasks on The robot, turn the robot OFF and unplug the Docking Station.

Dust Bin and Filters

Dust Bin

Dust Bin and Filters Maintenance

Main Brush and Side Brushes

Note: A Multi-Function Cleaning Tool is provided for easy maintenance. Handle with care, this cleaning tool has sharp edges.

Main Brush

Main Brush Maintenance

Side Brushes

Note: A Multi-Function Cleaning Tool is provided for easy maintenance. Handle with care, this cleaning tool has sharp edges.

Side Brushes Maintenance

Other Components

Other Components Maintenance

Note: Before cleaning the robot's Charging Contacts and Docking Station Pins, turn the robot OFF and unplug the Docking Station.

Regular Maintenance

To keep The robot running at peak performance, perform maintenance tasks and replace parts with the following frequencies:

Robot Part	Maintenance Frequency	Replacement Frequency
Side Brush	Once every 2 weeks	Every 3-6 months
Main Brush	Once per week	Every 6-12 months
Sponge Filter/ High Efficiency Filter	Once per week	Every 3-6 months
Universal Wheel Anti-Drop Sensors Bumper Charging Contacts Docking Station Pins	Once per week	/

A multi-function Cleaning Tool is provided for easy maintenance. Handle with care, this cleaning tool has sharp edges.

Note: YEEDI manufactures various replacement parts and fittings Please contact Customer Service for more information on replacement parts

Indicator Light

Scenario	Indicator Light
The robot is cleaning	AUTO Mode Button glows a solid WHITE
The robot is charging	AUTO Mode Button flashes WHITE
The robot has low battery	AUTO Mode Button glows a solid RED
The robot has a problem	AUTO Mode Button flashes RED
Programmed Cleaning Pattern is enabled	Cleaning Mode Switch Indicator lights up

Troubleshooting

No.	Malfunction	Possible Causes	Solutions
1	The robot is not charging	The robot is not switched ON	Switch ON the robot
		The robot has not connected to the Docking Station	Be sure that the robot's Charging Contacts have connected to the Docking Station Pins
		The battery is completely discharged	Re-activate the battery Switch ON the robot Place the robot on the Docking Station by hand, remove after charging for 3 minutes, repeat 3 times; then charge normally
2	The robot cannot return to the Docking Station	The Docking Station is not correctly placed	Please refer to Section "Preparation" to place the Docking Station correctly
		The Docking Station is unplugged or moved manually during the cleaning	Please make sure the Docking Station is plugged in and avoid move the Docking Station manually when the robot is cleaning
		The robot is working in a dark environment	Make sure the rooms to be cleaned are well illuminated
		The robot is stuck by obstacles (including wires, carpet tassels, or electric fan bases, etc ), or the door of the room where the Docking Station is placed is closed	Please refer to Section "Notes Before Cleaning" to tidy up the space before using the robot
		The robot is paused for more than 60 minutes, or manually moved out of 1-meter radius of the original position during the cleaning	It is suggested to pause the robot for no more than 60 minutes When moving the robot, keep the robot within 1-meter radius of the original position To ensure the cleaning efficiency, please try to avoid pausing or moving the robot during the cleaning
		The robot did not start cleaning from the Docking Station	It is suggested to start the robot from the Docking Station
3	The robot gets stuck while working and stops	The robot is tangled with something on the floor (electrical wires, curtains, carpet fringing, etc)	The robot will try various ways to free itself If it is unsuccessful, manually remove the obstacles and restart
4	The robot returns to the Docking Station before it has finished cleaning	When the battery gets low, The robot automatically switches to Return to Charger Mode and returns to the Docking Station to recharge itself	This is normal No solution necessary
4		Working time varies according to floor surface, room complexity and the Cleaning Mode selected	This is normal No solution necessary
5	The robot does not clean the whole area	The cleaning area is not tidy	Remove small objects from the floor and tidy up the cleaning area before The robot starts cleaning

Technical Specifications

Model	K701G
Working Voltage	144V DC
Docking Station Model	CH1630RC
Rated Input	100-240 V AC, 50-60 Hz, 25 W	Rated Output	20 V DC, 08 A
Remote Control Model	RC1633	Working Voltage	3 V DC
Remote Control Battery Type	AAA	Nominal Voltage	15 V DC
Off/Standby Mode Power	Less than 050 W
Networked Standby Power	Less than 200 W

Note: Technical and design specifications may be changed for continuous product improvement.
This equipment should be operated with a minimum distance of 20cm between the radiator and your body.