Yeedi Vac 2 PRO - Robot Vacuum and Mop Manual

Package Contents

Note: Figures and illustrations are for reference only and may differ from actual product appearance. Product design and specifications are subject to changes without notice.

Product Diagram

Main Unit

Bottom View

Dust Bin

Docking Station

Oscillating Mopping

Operating and Programming

Notes Before Cleaning

Tidy up the area to be cleaned by putting furniture, such as chairs, in their proper place.

During the first use, make sure each room door is open to help Robot fully explore your house.

It may be necessary to place a physical barrier at the edge of a drop to stop the unit from falling over the edge.

Put away objects including wires, cloths and slippers, etc. on the floor to improve the cleaning efficiency.

Before using the product on a rug with tasseled edges, please fold the rug edges under.

Please do not stand in narrow spaces, such as hallways, and make sure not to block the Detection Sensor.

Preparation

Please remove all protection materials on Robot and Docking Station before use.

1. Assemble Docking Station
   
2. Docking Station Placement
   
3. Install Edge Brush
   
4. Power ON
   
5. Charge Robot
   

Note: When Robot completes the cleaning cycle or when the battery gets low, Robot automatically returns to the Docking Station to recharge itself. Robot can also be sent back to the Docking Station at any time by using the yeedi App or by pressing the AUTO Button on the robot for 3 seconds.
Empty remaining water from the Reservoir before charging Robot.

yeedi App

To enjoy all available features, it is recommended to control your Robot via the yeedi App.

Before you start, make sure that:

• Your mobile phone is connected to a Wi-Fi network.
• The 2.4GHz band wireless signal is enabled on your router.
• The Wi-Fi indicator light on Robot is slowly flashing.

Wi-Fi Indicator Light

	Slowly flashing	Disconnected to Wi-Fi or waiting for Wi-Fi connection
	Rapidly flashing	Connecting to Wi-Fi
	Solid	Connected to Wi-Fi

Tips:
If you have any problems during the Wi-Fi setup process, refer to the Troubleshooting > Wi-Fi Connection section in this manual.

Start, Pause, Wake Up, Power Off

During the first cleaning:
Please supervise Robot and assist it should there be a problem.

1. Start
   Press
   
2. Pause
   
   Note: The robot's Control Panel stops glowing after the robot is paused for a few minutes. Press the AUTO Mode Button on Robot to wake it up.
3. Wake Up
   Press the AUTO button on Robot to wake it up
   
4. Power OFF
   
   Note: When Robot is not working, it is recommended to keep it switched ON and charging.

Oscillating Mopping

Note:

1. lnstall Oscillating Mopping for floor scrubbing.
2. With electric oscillating mopping up to 480 times per minute, Oscillating Mopping is applicable for area of highly concentrated dirt or dust.
3. Before installing Oscillating Mopping, please make sure the contacts are thoroughly dry.
4. Please avoid using Oscillating Mopping on the carpet.

1. Remove the Substitute Module
   
2. Add Water
   
3. Dry Contacts Thoroughly
   
4. Install Oscillating Mopping
   
5. Start Cleaning
   

* To prolong the service life of Oscillating Mopping, it is recommended to use purified water or softened water.
* Do not soak Oscillating Mopping in water.

Maintenance

Oscillating Mopping

1. Remove Oscillating Mopping
   
   * After Robot finishes mopping, please empty the reservoir.
2. Wipe Oscillating Mopping Clean
   
   * Wipe Oscillating Mopping with a clean, dry cloth. Do not soak into water.
3. Washable Mopping Pad (Oscillating Mopping)
   

Dust Bin and Filters

Note:

1. Please rinse the filter with water as shown above.
2. Do not use finger or brush to clean the filter.
3. Be sure to dry out the filter for at least 24 hours after washing.

Main Brush

Note: A Multi-Function Cleaning Tool is provided for easy maintenance. Handle with care, this cleaning tool has sharp edges.

Edge Brush

Mapping Sensor

Other Components

Note: Before cleaning the robot's Charging Contacts and Docking Station Pins, turn the robot OFF and unplug the Docking Station.

Regular Maintenance

To keep Robot running at peak performance, perform maintenance tasks and replace parts with the following frequencies:

A multi-function Cleaning Tool is provided for easy maintenance. Handle with care, this cleaning tool has sharp edges.
Note: yeedi manufactures various replacement parts and fittings. Please contact Customer Service for more information on replacement parts.

Indicator Light

Robot
Robot will tell you something is wrong with an indicator light and voice report. More detailed support is available through the yeedi app and online website.

Troubleshooting

Wi-Fi Connection

Before Wi-Fi setup, make sure Robot, mobile phone, and Wi-Fi network meet the following requirements.

Robot and Mobile Phone Requirements

• Robot is fully charged and the power switch of Robot is turned on.
• Wi-Fi status light slowly flashes.
• Turn off mobile phone's cellular data (you can turn it back on after setup).

Wi-Fi Network Requirements

• You are using a 2.4GHz or 2.4/5 GHz mixed network.
• Your router supports 802.11b/g/n and IPv4 protocol.
• Do not use a VPN (Virtual Private Network) or Proxy Server.
• Do not use a hidden network.
• WPA and WPA2 using TKIP, PSK, AES/CCMP encryption.
• WEP EAP (Enterprise Authentication Protocol) is not supported.
• Use Wi-Fi channels 1-11 in North America and channels 1-13 outside North America (refer to local regulatory agency).
• If you are using a network extender/repeater, the network name (SSID) and password are the same as your primary network.

Product Specifications

Model	YDVN11
Rated Input	20V 1A
Docking Station Model	CH1822		CH1918*
	Rated Input	100-240V 50-60Hz 0.5A	Rated Input (Charging)	For European Union Only	220-240V ~ 50-60Hz 0.3A
				For Russia Only	220V ~ 50-60Hz 0.3A
	Rated Output	20V 1A	Rated Output		20V 1A
	/		Power (Auto-Emptying)		1000W
Frequency bands	2400-2483.5MHz
Off Mode Power	Less than 0.50W
Networked Standby Power	Less than 2.00W

Output power of the Wi-Fi module is less than 100mW.
Note: Technical and design specifications may be changed for continuous product improvement.
* CH1918 is an Self-empty Station sold separately that automatically empties your Robot's dustbin.
Explore more accessories at https://www.yeedi.com.

Documents / Resources

References

• App Store - Apple
• Google Play
• yeedi | Self-Cleaning Robot Vacuum and Mop | Robot Vacuums – yeedi US

Download manual

Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.

Download Yeedi Vac 2 PRO - Robot Vacuum and Mop Manual