Step 16 Connect Power Supply - GE HDA2100HCC Installation Instructions Manual

CONNECT POWER SUPPLY
STEP 16
If a power cord with plug is already installed
proceed to Step 17.
WARNING
If house wiring is not 2-wire with ground, a ground
must be provided by the installer.
When house wiring is aluminum, be sure to use
UL-Listed anti-oxidant compound and aluminum-to-
copper connectors.
ADVERTENCIA
Si el cableado doméstico no cuenta con un cable
de 2 hilos con conexión a tierra, un instalador debe
realizar una conexión a tierra.
Cuando el cableado doméstico es de aluminio,
asegúrese de usar un compuesto antioxidante y
conectores de aluminio a cobre aprobados por UL.
• Secure house wiring to the back of the junction box
with a strain relief.
• Locate the 3 dishwasher wires, (white, black and green)
with the stripped ends coming out of the AC jumper. Use
UL-listed wire nuts of appropriate size to connect incoming
ground to green, white to white and black to black.
Home Wiring with Strain Relief
Ground
Junction
(Green)
Box
Bracket
Cover
Dishwasher Harness Wires
CAUTION
The Current Sensing Module (CSM) is a current-
sensing device located behind the toekick. It is
possible for the CSM to trip during shipping. If
that occurs, the installer can reset the CSM during
installation. If the CSM trips after the appliance
is installed and energized, DO NOT RESET THE
CSM. CALL SERVICE. Failure to have a qualified
service technician examine an installed dishwasher
after the CSM trips can result in personal injury or
damage to the appliance or property.
Dishwasher Installation
White
Black
CONNECT POWER SUPPLY
STEP 16
(CONT.)
PRECAUCIÓN
El Módulo de Detección Actualizada (Current
Sensing Module, CSM) es un dispositivo de
detección actualizada ubicado detrás del tope de
pie. Existe la posibilidad de que el CSM se caiga
durante el envío. Si esto ocurre, el instalador puede
reiniciar el CSM durante la instalación. Si el CSM se
cae luego de que el electrodoméstico fue instalado
y conectado, NO REINICIE EL CSM. LLAME AL
SERVICIO TÉCNICO. Si el lavavajillas ya instalado
no es examinado por un técnico calificado del
servicio técnico luego de una caída del CSM, se
podrán producir lesiones personales o daños sobre
el electrodoméstico o la propiedad.
STEP 17
INSTALL JUNCTION BOX
COVER
If junction box cover is already installed, skip to
Step 18.
WARNING
To reduce the risk of electric shock, fire, or injury to
persons, the installer should check to ensure that wires
are not pinched or damaged, the house wiring is attached
to the junction box bracket through a strain relief, and
all electrical connections made at the time of install (wire
nuts) are contained inside of the junction box cover.
ADVERTENCIA
Para reducir el riesgo de descarga eléctrica, incendio
o lesiones a personas, el instalador deberá realizar un
control para asegurar que los cables no estén pellizcados
ni dañados, que el cableado del hogar esté conectado a la
ficha de la caja de empalmes a través de un amortiguador
de refuerzo, y que todas las conexiones eléctricas realizadas
en el momento de la instalación (tuercas para cables) estén
dentro de la tapa de la caja de empalmes.
• In this step you will need the junction box cover and
the #10 Hex head screw from the screws set aside in
Step 1.
• Install the junction box cover using #10 hex head screw.
Check to be sure that wires are not pinched under the
cover and that all wire nuts are inside the cover.
13