Pentair Pool Products Hydromatic TRST Installation And Service Manual
  1. Manuals
  2. Brands
  3. Pentair Pool Products Manuals
  4. Water Pump
  5. Hydromatic TRST
  6. Installation and service manual

Pentair Pool Products Hydromatic TRST Installation And Service Manual

Low pressure sewage system
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
TRST
LOW PRESSURE SEWAGE SYSTEM
R
LISTED
NOTE! To the installer: Please make sure you provide
this manual to the owner of the pumping equipment or to
the responsible party who maintains the system.
Pump Installation and Service Manual

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Hydromatic TRST and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Pentair Pool Products Hydromatic TRST

Summary of Contents for Pentair Pool Products Hydromatic TRST

  • Page 1 Pump Installation and Service Manual TRST LOW PRESSURE SEWAGE SYSTEM LISTED NOTE! To the installer: Please make sure you provide this manual to the owner of the pumping equipment or to the responsible party who maintains the system.

  • Page 2: General Information

    for all Hydromatic pumps when Systems Description: General adjusting, dismantling, or repairing basic models Information the pump. Hydromatic TRST grinder systems are covered by these instructions: Inspection: Thank you for purchasing your 1. FBTRSTSG Factory built Check to be sure that all items for Hydromatic pump.

  • Page 3: Pump Installation

    Step 2 Step 4 Pump Apply pipe thread sealant to Attach lifting chain, cable or rope Installation discharge piping threads and screw as supplied to the lifting bail assembly into the pump discharge. shackle. Tighten threaded shackle vertical pump discharge pin with pliers.
  • Page 4 Step 2 Step 6 Pump An inlet grommet is the standard Close shut-off valve and make Installation supplied influent connection discharge line connection. It is device. If another type of inlet hub recommended that an additional is used, refer to the directions shut-off valve and redundant check Step 3 included with the hub.
  • Page 5 and panel. Mount sealing block Control Panel Wiring: and panel to pedestal with hardware provided. Ensure WARNING: To reduce risk pedestal gasket seals against electric shock, electric panel, and tighten all cord nuts installations shall while leaving approximately 3" of accordance with the National play in the cords from the tank.
  • Page 6 TYPICAL SIMPLEX – 230 VOLTS – SINGLE PHASE SCHEMATIC NOTE: Use copper, 60˚C. wire insulation for all field wiring terminals. WARNING: Disconnect power supply before servicing. WARNING: Metal back panel is to be connected to a good ground in accordance with local electrical codes. Figure 4...
  • Page 7 TYPICAL DUPLEX – 230 VOLTS – SINGLE PHASE SCHEMATIC NOTE: Use copper, 60˚C. wire insulation for all field wiring terminals. WARNING: Disconnect power supply before servicing. WARNING: Metal back panel is to be connected to a good ground in accordance with local electrical codes. Figure 5...

  • Page 8: Pump Operations

    Final Backfill for Fiberglass Basin Systems: Pump Refer to section “Excavation” for proper backfill materials. Ensure Operations backfill material is free of rocks, clods, and debris. See Figure 6. CAUTION: In freezing conditions the backfill must be dry and free Preoperation: of ice.

  • Page 9: Pump Troubleshooting

    CAUTION: Step 7 Pump excessive force when operating Float Adjustment for Troubleshooting the shutoff valve or damage to Simplex Systems: the valve or valve handle may Adjust floats so that the pump occur. The valve is closed when starts when the water level is just a noticeable stop is felt upon WARNING: Hazardous moving above the pump motor housing,...
  • Page 10 3. Start component(s) failure. end – nothing should happen. Pump While keeping the Off float Check start capacitor and start Troubleshooting tilted, tilt the On float in the relay for failure. same manner – the pump should come on. Suspend the On float 4.

  • Page 11: Parts List

    TRST Parts List ORDERING REPLACEMENT PARTS: Product improvements are made from time to time. The latest part design will be furnished as long as it is interchangeable with the old part.When ordering replacement parts, always furnish the following information: (1) pump serial number, (2) pump model and size, (3) part description, (4) part number, (5) impeller diameter (if ordering impeller), (6) quantity required, and (7) shipping instructions.

  • Page 12: Warranty

    WARRANTY Hydromatic warrants to the original purchaser of each Hydromatic product(s) that any part ® thereof that proves to be defective in material or workmanship within one year from date of installation or 18 months from manufacture date, whichever comes first, will be replaced at no charge with a new or remanufactured part, F.O.B.

Table of Contents