Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Pentair Pool Products Hydromatic S4LRC-3450 RPM
Summary of Contents for Pentair Pool Products Hydromatic S4LRC-3450 RPM
- Page 1 Pump Installation and Service Manual S4LRC-3450 RPM Submersible Sewage Pump Recessed Impeller NOTE! To the installer: Please make sure you provide this manual to the owner of the pumping equipment or to the responsible party who maintains the system.
-
Page 2: General Information
Pumps Operating control cord. Longer cable lengths General in Storage: can be furnished but must be Information specified at time of order. Power Pumps with carbon ceramic seals cable is 3 & 4 wire with separate must have impellers manually wire for ground. - Page 3 set at turn-on for one pump, and third pump in case of failure of with all pumps as proper starter one set for turn-on for two pumps. either or both of the first two heaters and connections for heat Pumps alternate operation on each pumps.
-
Page 4: Pump Installation
manually. Impeller may be slightly NEMA Junction Pump stuck due to factory test water (Optional): Information so it must be broken loose with If electrical control panel is to be small bar or screwdriver in edge set remote from the sump pump, of vanes. -
Page 5: Pump Operations
can cause considerable trouble. Installing 3900 Mercury Pump Switch Controls: (See Fig. 1.) Operations The controls are supported by a mounting bracket that is attached IMPORTANT: If equipment is to sump wall or cover or to the not properly wired and protected Starting System: NEMA 4 junction box. -
Page 6: Pump Maintenance
precautions per latest OSHA Pump Pump requirements; do not enter sump Operations Maintenance until these precautions strictly adhered to. Failure to heed above cautions lights on panel; pumps should As the motors are oil filled no could result in injury or death. alternate on each successive lubrication or other maintenance cycle of operation. - Page 7 4. Set assembly on bench and necessary completely BE SURE SEAL FAILURE remove connection box. When dismantle pump to change WIRE CONNECTED box is lifted off, connection bearings. If bearings are BEFORE HOUSING wires motor will damaged with dirt or heat, they ASSEMBLED.
- Page 8 on end of socket bolt to break face of bearing when replacing. Pump impeller loose from taper Pressing on outer face can Maintenance shaft. damage the bearing. Bearings are standard size that can be 6. Remove key and pry on each obtained from any bearing supply side of shoulder of shaft sleeve house or can be obtained from...
-
Page 9: Pump Troubleshooting
Auto position and turn off Total head is discharge gauge Pump main power. Put a jump wire pressure converted to feet Troubleshooting between 2 and 3 on terminal plus vertical height from strip. Turn on power and water level in sump to center if pump starts, trouble is in line of pressure gauge in Below is a list of common problems... -
Page 10: Parts List
S4LRC-3450 RPM Parts List ORDERING REPLACEMENT PARTS: Product improvements are made from time to time. The latest part design will be furnished as long as it is interchangeable with the old part.When ordering replacement parts, always furnish the following information: (1) pump serial number, (2) pump model and size, (3) part description, (4) part number, (5) impeller diameter (if ordering impeller), (6) quantity required, and (7) shipping instructions. -
Page 11: Wiring Diagrams
Wiring Diagrams... -
Page 12: Warranty
WARRANTY Hydromatic warrants to the original purchaser of each Hydromatic product(s) that any part ® thereof that proves to be defective in material or workmanship within one year from date of installation or 18 months from manufacture date, whichever comes first, will be replaced at no charge with a new or remanufactured part, F.O.B.
Need help?
Do you have a question about the Hydromatic S4LRC-3450 RPM and is the answer not in the manual?
Questions and answers