1. Manuals
  2. Brands
  3. Speco Manuals
  4. Security Camera
  5. O4B9M
  6. User manual

Speco O4B9M User Manual

4mp ip camera
Hide thumbs Also See for O4B9M:
Table of Contents

Advertisement

Quick Links

Download this manual
User Manual
4MP IP Camera
O4B9M / O4B9/O4D9/ O4D9M/ O4T9/ O4T9M
Please read this manual carefully before operating the unit and keep it for further reference

Advertisement

Table of Contents
loading

Related Manuals for Speco O4B9M

Summary of Contents for Speco O4B9M

  • Page 1 User Manual 4MP IP Camera O4B9M / O4B9/O4D9/ O4D9M/ O4T9/ O4T9M Please read this manual carefully before operating the unit and keep it for further reference...
  • Page 2 Important Safeguards and Warnings 1. Electrical safety All installation and operation here should conform to local electrical safety codes. Use a certified/listed 12VDC Class2 power supply only. Please note: Do not connect two power supplying sources to the device at the same time; it may result in device damage! The product must be grounded to reduce the risk of electric shock.
  • Page 3 Statement This guide is for reference only. Product, manuals, and specifications may be modified without prior notice. Speco Technologies reserves the right to modify these without notice and without incurring any obligation. Speco Technologies is not liable for any loss caused by improper operation.

  • Page 4: Table Of Contents

    Table of Contents Introduction ..........................................2 Web Access and Login ......................................3 Live View..........................................5 Camera Configuration ......................................7 System Configuration ................................7 4.1.1 System Information ..............................7 4.1.2 Date and Time ................................7 4.1.3 Local Recording ................................7 4.1.4 Storage ..................................
  • Page 5 4.6.1 User Admin ................................42 4.6.2 Online User ................................44 4.6.3 Block and Allow Lists ..............................44 4.6.4 Security Management...............................45 Maintenance Configuration ..............................46 4.7.1 Backup and Restore ..............................46 4.7.2 Reboot ..................................46 4.7.3 Upgrade ..................................46 4.7.4 Operation Log ................................47 Search ............................................ 48 Image Search ..................................48 Video Search ..................................50 5.2.1 Local Video Search ..............................50...

  • Page 6: Introduction

    Thank you for purchasing this network camera! Please read this manual carefully before operating the unit and retain it for further reference. Should you require any technical assistance, please contact Speco Technologies Technical Support at 1-800-645-5516. Main Features  Built-in PoE (Power over Ethernet) ...

  • Page 7: Web Access And Login

    2 Web Access and Login The IP camera settings can be accessed via a web browser through the LAN. Available web browser: IE (plug-in required)/ Firefox/Edge/Safari/Google Chrome It is recommended to use the latest version of these web browsers. The menu display and operation of the camera may be slightly different by using the browser with plug-in or without plug-in. Installing plug-in will display more functions of the camera.
  • Page 8 If this is the first time for you to log in, the password prompt may only change the admin password. To change ONVIF password, you either have to check the “Match Onvif Password” box (if available) or go to the the ONVIF section to change the password. (ConfigNetworkPorts/ConnectionsOnvif)

  • Page 9: Live View

    3 Live View The window below will be shown after logging in. The following table describes the icons on the live view interface Icon Description Icon Description Original size of resolution Rule information display Fit (correct scale) SD card recording indicator Auto (fill the window) Abnormal color indicator Full screen (show video only)
  • Page 10 Icon Description Icon Description Start/stop local recording Sensor alarm indicator Zoom in (for motorized models) Motion alarm indicator Zoom (for motorized Face detection indicator models) Zoom/Focus control (for Face detection motorized models) *Plug-in free live view: Two-way audio and local recording are not supported. ...

  • Page 11: Camera Configuration

    4 Camera Configuration Press the “Setup” button to go to the configuration interface. Note: Wherever applicable, click the “Save” button to save the settings. 4.1 System Configuration 4.1.1 System Information In the “System Information” interface, the system information of the device is listed. 4.1.2 Date and Time To set the time and date, go to SystemDate and Time.

  • Page 12: Storage

    Additionally, the snapshots triggered by smart events (including face detection, line crossing detection and intrusion detection) can be selected to save to the local PC. Rendering Mode: High-efficient mode, compatible mode or low-efficient mode can be optional. If the performance of your computer is not compatible with the web client or your computer has no graphics card, low-efficient mode is suggested.
  • Page 13 Weekly schedule Set the alarm time from Monday to Sunday for a single week. Each day is divided in one-hour increments. Green means scheduled. Blank means unscheduled. “Add”: Add the schedule for a special day. Drag the mouse to set the time on the timeline. “Erase”: Delete the schedule.

  • Page 14: Video Configuration

    same as the schedule recording (See Schedule Recording). 4.2 Video Configuration Video Configuration includes Image Settings, Video/Audio Setup, OSD, Privacy Mask and Region of Interest. 4.2.1 Image Configuration In the Image Settings interface as shown below, various settings can be adjusted, such as brightness, contrast, hue, and saturation and so on.
  • Page 15 Backlight Compensation (BLC): Off: disables the backlight compensation function. It is the default mode.  WDR: WDR can adjust the camera to provide a better image when there are both very bright and very dark areas simultaneously  in the field of the view by lowering the brightness of the bright area and increasing the brightness of the dark area. Recording will be stopped for a few seconds while the mode is changing from non-WDR to WDR mode.

  • Page 16: Video / Audio Configuration

    schedule. 4.2.2 Video / Audio Configuration Go to ImageVideo / Audio interface as shown below. In this interface, set the resolution, frame rate, bitrate type, video quality and so on subject to the actual network condition. Three video streams can be adjustable. Resolution: The size of image.

  • Page 17: Osd Configuration

    Audio Encoding: G711A and G711U are selectable. Audio Type: LIN. Some models may support MIC type. LIN IN/MIC IN Volume: LIN IN Volume can be set here. If MIC is selected, MIC IN volume can be set. (Only some models support MIC) Audio Out Volume: This function is available for the model with audio out interface.

  • Page 18: Roi Configuration

    To set up video mask: 1. Enable video mask. 2. Click the “Draw Area” button and then drag the mouse to draw the video mask area. 3. Click the “Save” button to save the settings. 4. Return to the live to verify that the area have been drawn as shown as blocked out in the image. To clear the video mask: Click the “Clear”...

  • Page 19: Zoom/Focus

    1. Check “Enable” and then click the “Draw Area” button. 2. Drag the mouse to set the ROI area. 3. Set the level. 4. Click the “Save” button to save the settings. 4.2.6 Zoom/Focus This function is only available for the model with motorized zoom lens. Within this section, zoom and focus can be controlled. If the image is out of focus after a manual adjustment, one key focus can be used to set the focus automatically.
  • Page 20 1. Check “Enable” check box to activate motion-based alarms. If unchecked, the camera will not send out any signals to trigger motion-based recording to the NVR or CMS, even if there is motion in the video. Alarm Holding Time: it refers to the interval time between the adjacent motion detections. For instance, if the alarm holding time is set to 20 seconds, once the camera detects a motion, it will go to alarm and would not detect any other motion in 20 seconds.

  • Page 21: Other Alarms

    4.3.2 Other Alarms  SD Card Full 1. Go to AlarmAnomalySD Card Full. 2. Click “Enable” and set the alarm holding time. 3. Set alarm trigger options. The setup steps are the same as motion detection. Please refer to motion detection chapter for details. ...

  • Page 22: Alarm In (Sensor Input)

    2. Click “Enable” and set the alarm holding time. 3. Trigger alarm out. When the IP address of the camera conflicts with the IP address of other devices, the system will trigger the alarm out.  Cable Disconnection This function is only available for the models with Alarm Out interface. 1.

  • Page 23: Alarm Out

    1. Click “Enable” and set the alarm type, alarm holding time and sensor name. 2. Set alarm trigger options. The setup steps are the same as motion detection. Please refer to motion detection chapter for details. 3. Click “Save” button to save the settings. 4.

  • Page 24: Alarm Server

    4.3.5 Alarm Server Go to AlarmAlarm Server interface as shown below. Set the server address, port, heartbeat, and heartbeat interval. When an alarm occurs, the camera will transfer the alarm event to the alarm server. If an alarm server is not needed, there is no need to configure this section. 4.4 Analytics Configuration This series of IP cameras supports certain smart functions, such as line crossing detection, region intrusion detection, etc.
  • Page 25 1. Enable object removal detection and then select the detection type. Enable Left Detection: Alarms will be triggered if there are items left in the pre-defined area. Enable Item Missing Detection: Alarms will be triggered if there are items missing in the pre-defined area. Shortest Holding Time: it is the alarm delay time of the object left in the region or removed from the region (ranges from 10~3600s).

  • Page 26: Exception

    ※ The configuration requirements of camera and surrounding areas 1. The range of the detection object should occupy from 1/50 to 1/3 of the entire image. 2. The detection time of objects in the camera shall be from 3 to 5 seconds. 3.

  • Page 27: Line Crossing

    of the scene change. The sensitivity value of Video Blur Detection: The higher the value is, the more sensitive the system responds to the blurriness of the image. The sensitivity value of Video Cast Detection: The higher the value is, the more sensitive the system responds to the color shift of the image.

  • Page 28: Intrusion

    4. Click “Save” button to save the settings. 5. Set area and sensitivity of the line crossing alarm. Click the “Area and Sensitivity” tab to go to the interface as shown below. Set the alarm line number and direction. Up to 4 lines can be added. Multiple lines cannot be added simultaneously. Direction：A<->B, A->B and A<-B optional.
  • Page 29 1. Enable intrusion alarm and select the snapshot type and the detection target. 2. Set the alarm holding time. 3. Set alarm trigger options. The setup steps are the same as motion detection. Please refer to motion detection chapter for details. 4.

  • Page 30: Face Detection

    1. Auto-focusing function should not be enabled for intrusion detection. 2. Avoid the scenes with many trees or the scenes with various light changes (like many flashing headlights). The ambient brightness of the scenes shouldn’t be too low. 3. Cameras should be mounted at a height of 10ft or above. 4.
  • Page 31 Use this to draw the approximate size of the face that you want the camera to capture. This is useful when there are multiple faces in the background or foreground that are not needed to be captured. To enable, Click “Draw Area” and drag the border lines of the rectangle to modify its size.

  • Page 32: Region Entrance

    4. The object distance depends on the focal-length of the lens mounted in the camera. 5. In order to guarantee the captured face recognition rate, the requirement for face capture are: left or right face turn angle is less than about 30°; pitching angle is less than 20°. 6.

  • Page 33: Region Exiting

    4.4.7 Region Exiting Region Exiting: Alarms will be triggered if the target exits from the pre-defined areas. Go to ConfigEventRegion Exiting interface as shown below. 1. Enable region exiting detection and select the snapshot type and the detection target. 2. Set the alarm holding time and alarm trigger options. 3.
  • Page 34 2. Enable target counting and select the snapshot type and the detection target. Detection Target: Select the target to calculate. Human, motor vehicle and motorcycle/bicycle can be selected. Staying Threshold: When the targets (human/vehicle) staying in the specified area exceed the threshold, alarms will be triggered. Counting Reset: The current number of the target counting can be reset.

  • Page 35: Region Statistics

    Set the alarm line number and direction. Only one alarm line can be added. Direction：A->B and A<-B can be optional. The direction of the arrow is entrance. Statistics: If enabled, you can see the statistical information in the live view interface. If disabled, the statistical information will not be displayed in the live view interface.
  • Page 36 2. Enable region statistics, select the snapshot type, the detection target, counting reset and alarm linkages. The setup steps are the same as the target counting by line. 3. Set the statistic area. Click the “Area” tab to go to the interface as shown below. Select the alarm area number on the right side.

  • Page 37: Heat Map

    6. View the statistical information of region statistics. Click ChartRegion Statistics to enter the following interface. Please select report type, count type and start time as needed. Then click “Count” to search the statistic result. Click “Chart” to view the statistic result intuitively. 4.4.10 Heat Map Heat Map is to display the flow distribution of people/vehicles in pre-defined areas by different colors.

  • Page 38: Network Configuration

    Click the “Draw Area” button and then click around the area where you want to set as the alarm area in the image on the left side (the alarm area should be a closed area). Click the “Stop Draw” button to stop drawing. Click the “Clear” button to delete the alarm area.

  • Page 39: Port

    Use IP address (take IPv4 for example)-obtain a local IP address automatically through DHCP. A typical router has a DHCP server built in, and therefore is able to assign an IP address to the camera. Use PPPoE-Click the “PPPoE Config” tab to go to the interface as shown below. Enable PPPoE and then enter the user name and password from your ISP.

  • Page 40: Server Configuration

    HTTP Port: The default HTTP port is 80. It can be changed to any port which is not occupied. HTTPS Port: The default HTTPs port is 443. It can be changed to any port which is not occupied. Data Port: The default data port is 9008. Please change it as necessary. RTSP Port: The default port is 554.

  • Page 41: Ddns

    Note: when adding the device to the third-party platform with ONVIF/RTSP protocol, please enter the username and password created in the above interface. 4.5.5 DDNS If the camera is set up with a DHCP connection, DDNS should be set for accessing the camera from the internet. 1.

  • Page 42: 802.1X

    2. Check the corresponding version checkbox (Enable SNMPv1, Enable SNMPv2, Enable SNMPv3) according to the version of the SNMP software that will be used. 3. Set the values for “Read SNMP Community”, “Write SNMP Community”, “Trap Address”, “Trap Port” and so on. Please make sure the settings are the same as that of the SNMP software.

  • Page 43: Rtsp

    authentication system to identify the device in a local network. If the camera connected to the network interface of the switch has passed the authentication of the switch, it can be accessed via the local network. Protocol type and EAPOL version: Please use the default settings. User name and password: The user name and password must be the same with the user name and password applied for and registered in the authentication server.

  • Page 44: Upnp

    Check “Enable”, select stream type, set the reconnection time after timeout and server address as needed. Server address: Enter the server address allocated by the third party server. After that, click “Save” to save the settings. Then click “Refresh” to view the connection status. 4.5.10 UPNP If this function is enabled, the camera can be quickly accessed through the LAN.

  • Page 45: Https

    Server Name: The name of the FTP server. Server Address: The IP address or domain name of the FTP. Upload Path: The directory where files will be uploaded to. Port: The port of the FTP server. Use Name and Password: The username and password that are used to login to the FTP server. 4.5.13 HTTPS HTTPs provides authentication of the web site and protects user privacy.

  • Page 46: Qos

    Click the “Create” button to create a private certificate. Enter the country (only two letters available), domain (camera’s IP address/domain), validity date, password, province/state, region and so on. Then click “OK” to save the settings. * Click “Create a certificate request” to enter the following interface. Click “Create”...
  • Page 47 Add user: 1. Click “Add” to pop up the following textbox. 2. Enter user name in “User Name” textbox. 3. Enter letters or numbers in “Password” and “Confirm Password” textbox. Please set the password according to the requirement of the password security level (Go to SetupSecuritySecurity ManagementPassword Security interface to set the security level). 4.

  • Page 48: Online User

    3. Enter the old password of the user in the “Old Password” text box. 4. Enter the new password in the “New password” and “Confirm Password” text box. 5. Modify the permission as necessary. 6. Click the “OK” button to save the settings. Note: To change the access level of a user, the user must be deleted and added again with the new access level.

  • Page 49: Security Management

    The setup steps are as follows: Check the “Enable address filtering” check box. Select “Block/Allow the following address”, IPv4/IPv6 and then enter IP address in the address box and click the “Add” button. 4.6.4 Security Management Go to SecuritySecurity Management as shown below. In order to prevent against malicious password unlocking, “locking once illegal login”...

  • Page 50: Maintenance Configuration

    4.7 Maintenance Configuration 4.7.1 Backup and Restore Go to MaintenanceBackup & Restore. Import & Export Settings  Configuration settings of the camera can be exported form a camera into another camera. 1. Click “Browse” to select the save path for import or export information on the PC. 2.

  • Page 51: Operation Log

    4.7.4 Operation Log To query and export log: 1. Go to MaintenanceOperation Log. 2. Select the main type, sub type, start and end time. 3. Click “Search” to view the operation log. 4. Click “Export” to export the operation log.

  • Page 52: Search

    5 Search 5.1 Image Search In the Setup interface, click Search to go to the interface as shown below. Images that are saved on the PC or SD card can be found here.  Local Image Search 1. Choose “Picture”—“Local”. 2.
  • Page 53 Click to return to the previous interface.  SD Card Image Search 1. Choose “Picture”—“SD Card”. 2. Set time: Select date and choose the start and end time. 3. Choose the alarm events at the bottom of the interface. 4. Click to search the images.

  • Page 54: Video Search

    Icon Description Icon Description Close: Select an image and click Close all: Click this button to close all this button to close the image. images. Save: Click this button to select the Save all: Click this button to select the path for saving the image on the path for saving all pictures on the PC.

  • Page 55: Sd Card Video Search

    Icon Description Icon Description Play button. After pausing the video, Pause button click this button to continue playing. Stop button Speed down Speed up Watermark display Enable / disable audio; drag the slider to adjust the volume after enabling audio. 5.2.2 SD Card Video Search Click Search to go to the interface as shown below.
  • Page 56 4. Select the alarm events at the bottom of the interface. 5. Select mix stream (video and audio stream) or video stream as needed. 6. Double click on a file name in the list to start playback. The time table can be shown in 24H/12H/2H/1H format by clicking the corresponding buttons. Video clip and downloading 1.
  • Page 57 Click “Set up” to set the storage directory of the video files. Click “Open” to play the video. Click “Clear List” to clear the downloading list. Click “Close” to close the downloading window.

  • Page 58: Appendix

    Appendix Appendix 1 Troubleshooting IP Scanner does not show any device. Make sure that the PC that’s running IP Scanner is on the same local network as the devices. Internet Explorer cannot download ActiveX control. IE browser may be set up to block ActiveX. Follow the steps below. 1.
  • Page 59 Models: O4B9M / O4B9/O4D9/ O4D9M/ O4T9/ O4T9M Federal Communications Commission (FCC) Statements This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.

This manual is also suitable for:

O4b9O4d9O4d9mO4t9O4t9m

Table of Contents