Tips And Tricks; Environmental Protection; Technical Specifications - Metabo SXE 425 TurboTec Original Instructions Manual

en ENGLISH
- Replace the old braking ring (15) with the new
braking ring (see page 2), ensuring that the new
braking ring is in the same position as the old
braking ring. Ensure that the position of the
marking on the braking ring is correct.
- For proper functioning, apply a thin layer of grease
(see page 2) on the braking ring at its contact
surface to the support plate.
- Mount support plate (2) and rotate until it engages
on carrier disc.
- Insert locking screw (14) again and tighten.

9. Tips and Tricks

Do not press the device too firmly against the
surface being sanded. This does not improve, but
rather impairs, the sanding performance.
Empty the dust bag (12) in good time to optimise
dust extraction.
Use a suitable sanding disc to achieve the best
possible work results: Removal of old paint layers =
P 40
Pre-sanding of wood = P 60, P 80
Finishing of wood = P 100, P 120
Sanding of veneers, sealing primer, filler, paint = P
180, P 240, P 320, P 400
10. Accessories
Use only genuine Metabo accessories.
Note: Metabo accessories are adapted to suit the
machine's velcro-type fastening. This increases the
service life of the velcro-type fastening.
Use only accessories which fulfil the requirements
and specifications listed in these operating
instructions.
See www.metabo.com or the catalogue for a
complete range of accessories.
11. Repairs
Repairs to electrical tools must be carried out by
qualified electricians ONLY!
A defective mains cable must only be replaced with
a special, original mains cable from metabo, which
is available only from the Metabo service.
If the mains connection cable of this machine is
damaged, it must be replaced by the manufacturer or
an authorized service centre to avoid hazard.
If you have Metabo electrical tools that require
repairs, please contact your Metabo service centre.
For addresses see www.metabo.com.
You can download spare parts lists from
www.metabo.com.

12. Environmental Protection

Observe national regulations on environmentally
compatible disposal and on the recycling of disused
machines, packaging and accessories.
Only for EU countries: Never dispose of
power tools in your household waste! In
10
accordance with European Guideline
2012/19/EU on used electronic and electric
equipment and its implementation in national
legal systems, used power tools must be collected
separately and handed in for environmentally
compatible recycling.

13. Technical Specifications

Explanatory notes on the specifications on page 3.
Changes due to technological progress reserved.
D = Diameter of support plate
P = Nominal power input
1
P = Power output
2
n = Idle speed (setting wheel)
0
n = Idle speed (TurboBoost switch)
0, TB
n = Speed at rated load (TurboBoost
1, TB
switch)
s = Oscillating frequency at idle speed
0
(setting wheel)
s = Oscillating frequency at idle speed
0, TB
(TurboBoost switch)
s = Oscillating frequency at rated load
1, TB
(TurboBoost switch)
S = Oscillating circuit diameter
m = Weight without mains cable
Measured values determined in conformity with
EN 62841.
Machine in protection class II
~
AC Power
The technical specifications quoted are subject to
tolerances (in compliance with the relevant valid
standards).
Emission values
These values make it possible to assess the
emissions from the power tool and to compare
different power tools. The actual load may be higher
or lower depending on the operating conditions, the
condition of the power tool or the accessories.
Please allow for breaks and periods when the load
is lower for assessment purposes. Arrange
protective measures for the user e.g. organisational
measures based on the adjusted estimates.
Vibration total value (vector sum of three directions)
determined in accordance with EN 62841:
a = Vibration emission value (surface
h
grinding)
K = Uncertainty (vibration)
h
Typical A-effective perceived sound levels:
L = Sound-pressure level
pA
L = Acoustic power level
WA
K , K = Uncertainty
pA WA
The noise level can exceed 80 dB(A) during
operation.
Wear ear protectors!